Subversion Repositories Kolibri OS

 

                           Üßßß

                         ÜÜÛÜÜ ÜÜÜÜ    ÜÜÜÜÜ ÜÜÜ ÜÜ

                           Û       Û  Û      Û  Û  Û

                           Û  ÜßßßßÛ   ßßßßÜ Û  Û  Û

                           Û  ßÜÜÜÜÛÜ ÜÜÜÜÜß Û  Û  Û

 

                              flat assembler 1.73

                              Programmer's Manual

 

 

Table of contents

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

 

Chapter 1  Introduction

 

        1.1  Compiler overview

        1.1.1  System requirements

        1.1.2  Executing compiler from command line

        1.1.3  Compiler messages

        1.1.4  Output formats

 

        1.2  Assembly syntax

        1.2.1  Instruction syntax

        1.2.2  Data definitions

        1.2.3  Constants and labels

        1.2.4  Numerical expressions

        1.2.5  Jumps and calls

        1.2.6  Size settings

 

Chapter 2  Instruction set

 

        2.1  The x86 architecture instructions

        2.1.1  Data movement instructions

        2.1.2  Type conversion instructions

        2.1.3  Binary arithmetic instructions

        2.1.4  Decimal arithmetic instructions

        2.1.5  Logical instructions

        2.1.6  Control transfer instructions

        2.1.7  I/O instructions

        2.1.8  Strings operations

        2.1.9  Flag control instructions

        2.1.10  Conditional operations

        2.1.11  Miscellaneous instructions

        2.1.12  System instructions

        2.1.13  FPU instructions

        2.1.14  MMX instructions

        2.1.15  SSE instructions

        2.1.16  SSE2 instructions

        2.1.17  SSE3 instructions

        2.1.18  AMD 3DNow! instructions

        2.1.19  The x86-64 long mode instructions

        2.1.20  SSE4 instructions

        2.1.21  AVX instructions

        2.1.22  AVX2 instructions

        2.1.23  Auxiliary sets of computational instructions

        2.1.24  AVX-512 instructions

        2.1.25  Other extensions of instruction set

 

        2.2  Control directives

        2.2.1  Numerical constants

        2.2.2  Conditional assembly

        2.2.3  Repeating blocks of instructions

        2.2.4  Addressing spaces

        2.2.5  Other directives

        2.2.6  Multiple passes

 

        2.3  Preprocessor directives

        2.3.1  Including source files

        2.3.2  Symbolic constants

        2.3.3  Macroinstructions

        2.3.4  Structures

        2.3.5  Repeating macroinstructions

        2.3.6  Conditional preprocessing

        2.3.7  Order of processing

 

        2.4  Formatter directives

        2.4.1  MZ executable

        2.4.2  Portable Executable

        2.4.3  Common Object File Format

        2.4.4  Executable and Linkable Format

 

 

 

Chapter 1  Introduction

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

 

This chapter contains all the most important information you need to begin

using the flat assembler. If you are experienced assembly language programmer,

you should read at least this chapter before using this compiler.

 

 

1.1  Compiler overview

 

Flat assembler is a fast assembly language compiler for the x86 architecture

processors, which does multiple passes to optimize the size of generated

machine code. It is self-compilable and versions for different operating

systems are provided. All the versions are designed to be used from the system

command line and they should not differ in behavior.

 

 

1.1.1  System requirements

 

All versions require the x86 architecture 32-bit processor (at least 80386),

although they can produce programs for the x86 architecture 16-bit processors,

too. DOS version requires an OS compatible with MS DOS 2.0 and either true

real mode environment or DPMI. Windows version requires a Win32 console

compatible with 3.1 version.

 

 

1.1.2  Executing compiler from command line

 

To execute flat assembler from the command line you need to provide two

parameters - first should be name of source file, second should be name of

destination file. If no second parameter is given, the name for output

file will be guessed automatically. After displaying short information about

the program name and version, compiler will read the data from source file and

compile it. When the compilation is successful, compiler will write the

generated code to the destination file and display the summary of compilation

process; otherwise it will display the information about error that occurred.

  The source file should be a text file, and can be created in any text

editor. Line breaks are accepted in both DOS and Unix standards, tabulators

are treated as spaces.

  In the command line you can also include "-m" option followed by a number,

which specifies how many kilobytes of memory flat assembler should maximally

use. In case of DOS version this options limits only the usage of extended

memory. The "-p" option followed by a number can be used to specify the limit

for number of passes the assembler performs. If code cannot be generated

within specified amount of passes, the assembly will be terminated with an

error message. The maximum value of this setting is 65536, while the default

limit, used when no such option is included in command line, is 100.

It is also possible to limit the number of passes the assembler

performs, with the "-p" option followed by a number specifying the maximum

number of passes.

  There are no command line options that would affect the output of compiler,

flat assembler requires only the source code to include the information it

really needs. For example, to specify output format you specify it by using

the "format" directive at the beginning of source.

 

 

1.1.3  Compiler messages

 

As it is stated above, after the successful compilation, the compiler displays

the compilation summary. It includes the information of how many passes was

done, how much time it took, and how many bytes were written into the

destination file.

The following is an example of the compilation summary:

 

flat assembler  version 1.72 (16384 kilobytes memory)

38 passes, 5.3 seconds, 77824 bytes.

 

In case of error during the compilation process, the program will display an

error message. For example, when compiler can't find the input file, it will

display the following message:

 

flat assembler  version 1.72 (16384 kilobytes memory)

error: source file not found.

 

If the error is connected with a specific part of source code, the source line

that caused the error will be also displayed. Also placement of this line in

the source is given to help you finding this error, for example:

 

flat assembler  version 1.72 (16384 kilobytes memory)

example.asm [3]:

        mob     ax,1

error: illegal instruction.

 

It means that in the third line of the "example.asm" file compiler has

encountered an unrecognized instruction. When the line that caused error

contains a macroinstruction, also the line in macroinstruction definition

that generated the erroneous instruction is displayed:

 

flat assembler  version 1.72 (16384 kilobytes memory)

example.asm [6]:

        stoschar 7

example.asm [3] stoschar [1]:

        mob     al,char

error: illegal instruction.

 

It means that the macroinstruction in the sixth line of the "example.asm" file

generated an unrecognized instruction with the first line of its definition.

 

 

1.1.4  Output formats

 

By default, when there is no "format" directive in source file, flat

assembler simply puts generated instruction codes into output, creating this

way flat binary file. By default it generates 16-bit code, but you can always

turn it into the 16-bit or 32-bit mode by using "use16" or "use32" directive.

Some of the output formats switch into 32-bit mode, when selected - more

information about formats which you can choose can be found in 2.4.

  All output code is always in the order in which it was entered into the

source file.

 

 

1.2  Assembly syntax

 

The information provided below is intended mainly for the assembly language

programmers that have been using some other assembly compilers before.

If you are beginner, you should look for the assembly programming tutorials.

  Flat assembler by default uses the Intel syntax for the assembly

instructions, although you can customize it using the preprocessor

capabilities (macroinstructions and symbolic constants). It also has its own

set of the directives - the instructions for compiler.

  All symbols defined inside the sources are case-sensitive.

 

 

1.2.1  Instruction syntax

 

Instructions in assembly language are separated by line breaks, and one

instruction is expected to fill the one line of text. If a line contains

a semicolon, except for the semicolons inside the quoted strings, the rest of

this line is the comment and compiler ignores it. If a line ends with "\"

character (eventually the semicolon and comment may follow it), the next line

is attached at this point.

  Each line in source is the sequence of items, which may be one of the three

types. One type are the symbol characters, which are the special characters

that are individual items even when are not spaced from the other ones.

Any of the "+-*/=<>()[]{}:,|&~#`" is the symbol character. The sequence of

other characters, separated from other items with either blank spaces or

symbol characters, is a symbol. If the first character of symbol is either a

single or double quote, it integrates any sequence of characters following it,

even the special ones, into a quoted string, which should end with the same

character, with which it began (the single or double quote) - however if there

are two such characters in a row (without any other character between them),

they are integrated into quoted string as just one of them and the quoted

string continues then. The symbols other than symbol characters and quoted

strings can be used as names, so are also called the name symbols.

  Every instruction consists of the mnemonic and the various number of

operands, separated with commas. The operand can be register, immediate value

or a data addressed in memory, it can also be preceded by size operator to

define or override its size (table 1.1). Names of available registers you can

find in table 1.2, their sizes cannot be overridden. Immediate value can be

specified by any numerical expression.

  When operand is a data in memory, the address of that data (also any

numerical expression, but it may contain registers) should be enclosed in

square brackets or preceded by "ptr" operator. For example instruction

"mov eax,3" will put the immediate value 3 into the EAX register, instruction

"mov eax,[7]" will put the 32-bit value from the address 7 into EAX and the

instruction "mov byte [7],3" will put the immediate value 3 into the byte at

address 7, it can also be written as "mov byte ptr 7,3". To specify which

segment register should be used for addressing, segment register name followed

by a colon should be put just before the address value (inside the square

brackets or after the "ptr" operator).

 

   Table 1.1  Size operators

  ÚÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÂÄÄÄÄÄÄÄ¿

  ³ Operator ³ Bits ³ Bytes ³

  ÆÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍØÍÍÍÍÍÍ͵

  ³ byte     ³ 8    ³ 1     ³

  ³ word     ³ 16   ³ 2     ³

  ³ dword    ³ 32   ³ 4     ³

  ³ fword    ³ 48   ³ 6     ³

  ³ pword    ³ 48   ³ 6     ³

  ³ qword    ³ 64   ³ 8     ³

  ³ tbyte    ³ 80   ³ 10    ³

  ³ tword    ³ 80   ³ 10    ³

  ³ dqword   ³ 128  ³ 16    ³

  ³ xword    ³ 128  ³ 16    ³

  ³ qqword   ³ 256  ³ 32    ³

  ³ yword    ³ 256  ³ 32    ³

  ³ dqqword  ³ 512  ³ 64    ³

  ³ zword    ³ 512  ³ 64    ³

  ÀÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÁÄÄÄÄÄÄÄÙ

 

   Table 1.2  Registers

  ÚÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿

  ³ Type    ³ Bits ³                                                ³

  ÆÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͵

  ³         ³ 8    ³ al    cl    dl    bl    ah    ch    dh    bh   ³

  ³ General ³ 16   ³ ax    cx    dx    bx    sp    bp    si    di   ³

  ³         ³ 32   ³ eax   ecx   edx   ebx   esp   ebp   esi   edi  ³

  ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ Segment ³ 16   ³ es    cs    ss    ds    fs    gs               ³

  ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ Control ³ 32   ³ cr0         cr2   cr3   cr4                    ³

  ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ Debug   ³ 32   ³ dr0   dr1   dr2   dr3               dr6   dr7  ³

  ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ FPU     ³ 80   ³ st0   st1   st2   st3   st4   st5   st6   st7  ³

  ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ MMX     ³ 64   ³ mm0   mm1   mm2   mm3   mm4   mm5   mm6   mm7  ³

  ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ SSE     ³ 128  ³ xmm0  xmm1  xmm2  xmm3  xmm4  xmm5  xmm6  xmm7 ³

  ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ AVX     ³ 256  ³ ymm0  ymm1  ymm2  ymm3  ymm4  ymm5  ymm6  ymm7 ³

  ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ AVX-512 ³ 512  ³ zmm0  zmm1  zmm2  zmm3  zmm4  zmm5  zmm6  zmm7 ³

  ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ Opmask  ³ 64   ³ k0    k1    k2    k3    k4    k5    k6    k7   ³

  ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ Bounds  ³ 128  ³ bnd0  bnd1  bnd2  bnd3                         ³

  ÀÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

 

 

1.2.2  Data definitions

 

To define data or reserve a space for it, use one of the directives listed in

table 1.3. The data definition directive should be followed by one or more of

numerical expressions, separated with commas. These expressions define the

values for data cells of size depending on which directive is used. For

example "db 1,2,3" will define the three bytes of values 1, 2 and 3

respectively.

  The "db" and "du" directives also accept the quoted string values of any

length, which will be converted into chain of bytes when "db" is used and into

chain of words with zeroed high byte when "du" is used. For example "db 'abc'"

will define the three bytes of values 61, 62 and 63.

  The "dp" directive and its synonym "df" accept the values consisting of two

numerical expressions separated with colon, the first value will become the

high word and the second value will become the low double word of the far

pointer value. Also "dd" accepts such pointers consisting of two word values

separated with colon, and "dt" accepts the word and quad word value separated

with colon, the quad word is stored first. The "dt" directive with single

expression as parameter accepts only floating point values and creates data in

FPU double extended precision format.

  Any of the above directive allows the usage of special "dup" operator to

make multiple copies of given values. The count of duplicates should precede

this operator and the value to duplicate should follow - it can even be the

chain of values separated with commas, but such set of values needs to be

enclosed with parenthesis, like "db 5 dup (1,2)", which defines five copies

of the given two byte sequence.

  The "file" is a special directive and its syntax is different. This

directive includes a chain of bytes from file and it should be followed by the

quoted file name, then optionally numerical expression specifying offset in

file preceded by the colon, and - also optionally - comma and numerical

expression specifying count of bytes to include (if no count is specified, all

data up to the end of file is included). For example "file 'data.bin'" will

include the whole file as binary data and "file 'data.bin':10h,4" will include

only four bytes starting at offset 10h.

  The data reservation directive should be followed by only one numerical

expression, and this value defines how many cells of the specified size should

be reserved. All data definition directives also accept the "?" value, which

means that this cell should not be initialized to any value and the effect is

the same as by using the data reservation directive. The uninitialized data

may not be included in the output file, so its values should be always

considered unknown.

 

   Table 1.3  Data directives

  ÚÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄ¿

  ³ Size    ³ Define ³ Reserve ³

  ³ (bytes) ³ data   ³ data    ³

  ÆÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍ͵

  ³ 1       ³ db     ³ rb      ³

  ³         ³ file   ³         ³

  ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄ´

  ³ 2       ³ dw     ³ rw      ³

  ³         ³ du     ³         ³

  ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄ´

  ³ 4       ³ dd     ³ rd      ³

  ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄ´

  ³ 6       ³ dp     ³ rp      ³

  ³         ³ df     ³ rf      ³

  ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄ´

  ³ 8       ³ dq     ³ rq      ³

  ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄ´

  ³ 10      ³ dt     ³ rt      ³

  ÀÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÙ

 

 

1.2.3  Constants and labels

 

In the numerical expressions you can also use constants or labels instead of

numbers. To define the constant or label you should use the specific

directives. Each label can be defined only once and it is accessible from the

any place of source (even before it was defined). Constant can be redefined

many times, but in this case it is accessible only after it was defined, and

is always equal to the value from last definition before the place where it's

used. When a constant is defined only once in source, it is - like the label -

accessible from anywhere.

  The definition of constant consists of name of the constant followed by the

"=" character and numerical expression, which after calculation will become

the value of constant. This value is always calculated at the time the

constant is defined. For example you can define "count" constant by using the

directive "count = 17", and then use it in the assembly instructions, like

"mov cx,count" - which will become "mov cx,17" during the compilation process.

  There are different ways to define labels. The simplest is to follow the

name of label by the colon, this directive can even be followed by the other

instruction in the same line. It defines the label whose value is equal to

offset of the point where it's defined. This method is usually used to label

the places in code. The other way is to follow the name of label (without a

colon) by some data directive. It defines the label with value equal to

offset of the beginning of defined data, and remembered as a label for data

with cell size as specified for that data directive in table 1.3.

  The label can be treated as constant of value equal to offset of labeled

code or data. For example when you define data using the labeled directive

"char db 224", to put the offset of this data into BX register you should use

"mov bx,char" instruction, and to put the value of byte addressed by "char"

label to DL register, you should use "mov dl,[char]" (or "mov dl,ptr char").

But when you try to assemble "mov ax,[char]", it will cause an error, because

fasm compares the sizes of operands, which should be equal. You can force

assembling that instruction by using size override: "mov ax,word [char]", but

remember that this instruction will read the two bytes beginning at "char"

address, while it was defined as a one byte.

  The last and the most flexible way to define labels is to use "label"

directive. This directive should be followed by the name of label, then

optionally size operator (it can be preceded by a colon) and then - also

optionally "at" operator and the numerical expression defining the address at

which this label should be defined. For example "label wchar word at char"

will define a new label for the 16-bit data at the address of "char". Now the

instruction "mov ax,[wchar]" will be after compilation the same as

"mov ax,word [char]". If no address is specified, "label" directive defines

the label at current offset. Thus "mov [wchar],57568" will copy two bytes

while "mov [char],224" will copy one byte to the same address.

  The label whose name begins with dot is treated as local label, and its name

is attached to the name of last global label (with name beginning with

anything but dot) to make the full name of this label. So you can use the

short name (beginning with dot) of this label anywhere before the next global

label is defined, and in the other places you have to use the full name. Label

beginning with two dots are the exception - they are like global, but they

don't become the new prefix for local labels.

  The "@@" name means anonymous label, you can have defined many of them in

the source. Symbol "@b" (or equivalent "@r") references the nearest preceding

anonymous label, symbol "@f" references the nearest following anonymous label.

These special symbol are case-insensitive.

 

 

1.2.4  Numerical expressions

 

In the above examples all the numerical expressions were the simple numbers,

constants or labels. But they can be more complex, by using the arithmetical

or logical operators for calculations at compile time. All these operators

with their priority values are listed in table 1.4. The operations with higher

priority value will be calculated first, you can of course change this

behavior by putting some parts of expression into parenthesis. The "+", "-",

"*" and "/" are standard arithmetical operations, "mod" calculates the

remainder from division. The "and", "or", "xor", "shl", "shr", "bsf", "bsr"

and "not" perform the same bit-logical operations as assembly instructions of

those names. The "rva" and "plt" are special unary operators that perform

conversions between different kinds of addresses, they can be used only with

few of the output formats and their meaning may vary (see 2.4).

  The arithmetical and bit-logical calculations are processed as if they

operated on infinite precision 2-adic numbers, and assembler signalizes an

overflow error if because of its limitations it is not table to perform the

required calculation, or if the result is too large number to fit in either

signed or unsigned range for the destination unit size.

  The numbers in the expression are by default treated as a decimal, binary

numbers should have the "b" letter attached at the end, octal number should

end with "o" letter, hexadecimal numbers should begin with "0x" characters

(like in C language) or with the "$" character (like in Pascal language) or

they should end with "h" letter. Also quoted string, when encountered in

expression, will be converted into number - the first character will become

the least significant byte of number.

  The numerical expression used as an address value can also contain any of

general registers used for addressing, they can be added and multiplied by

appropriate values, as it is allowed for the x86 architecture instructions.

The numerical calculations inside address definition by default operate with

target size assumed to be the same as the current bitness of code, even if

generated instruction encoding will use a different address size.

  There are also some special symbols that can be used inside the numerical

expression. First is "$", which is always equal to the value of current

offset, while "$$" is equal to base address of current addressing space. The

other one is "%", which is the number of current repeat in parts of code that

are repeated using some special directives (see 2.2) and zero anywhere else.

There's also "%t" symbol, which is always equal to the current time stamp.

  Any numerical expression can also consist of single floating point value

(flat assembler does not allow any floating point operations at compilation

time) in the scientific notation, they can end with the "f" letter to be

recognized, otherwise they should contain at least one of the "." or "E"

characters. So "1.0", "1E0" and "1f" define the same floating point value,

while simple "1" defines an integer value.

 

   Table 1.4  Arithmetical and bit-logical operators by priority

  ÚÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿

  ³ Priority ³ Operators    ³

  ÆÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍ͵

  ³ 0        ³ +  -         ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ 1        ³ *  /         ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ 2        ³ mod          ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ 3        ³ and  or  xor ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ 4        ³ shl  shr     ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ 5        ³ not          ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ 6        ³ bsf  bsr     ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ 7        ³ rva  plt     ³

  ÀÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

 

 

1.2.5  Jumps and calls

 

The operand of any jump or call instruction can be preceded not only by the

size operator, but also by one of the operators specifying type of the jump:

"short", "near" or "far". For example, when assembler is in 16-bit mode,

instruction "jmp dword [0]" will become the far jump and when assembler is

in 32-bit mode, it will become the near jump. To force this instruction to be

treated differently, use the "jmp near dword [0]" or "jmp far dword [0]" form.

  When operand of near jump is the immediate value, assembler will generate

the shortest variant of this jump instruction if possible (but will not create

32-bit instruction in 16-bit mode nor 16-bit instruction in 32-bit mode,

unless there is a size operator stating it). By specifying the jump type

you can force it to always generate long variant (for example "jmp near 0")

or to always generate short variant and terminate with an error when it's

impossible (for example "jmp short 0").

 

 

1.2.6  Size settings

 

When instruction uses some memory addressing, by default the smallest form of

instruction is generated by using the short displacement if only address

value fits in the range. This can be overridden using the "word" or "dword"

operator before the address inside the square brackets (or after the "ptr"

operator), which forces the long displacement of appropriate size to be made.

In case when address is not relative to any registers, those operators allow

also to choose the appropriate mode of absolute addressing.

  Instructions "adc", "add", "and", "cmp", "or", "sbb", "sub" and "xor" with

first operand being 16-bit or 32-bit are by default generated in shortened

8-bit form when the second operand is immediate value fitting in the range

for signed 8-bit values. It also can be overridden by putting the "word" or

"dword" operator before the immediate value. The similar rules applies to the

"imul" instruction with the last operand being immediate value.

  Immediate value as an operand for "push" instruction without a size operator

is by default treated as a word value if assembler is in 16-bit mode and as a

double word value if assembler is in 32-bit mode, shorter 8-bit form of this

instruction is used if possible, "word" or "dword" size operator forces the

"push" instruction to be generated in longer form for specified size. "pushw"

and "pushd" mnemonics force assembler to generate 16-bit or 32-bit code

without forcing it to use the longer form of instruction.

 

 

Chapter 2  Instruction set

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

 

This chapter provides the detailed information about the instructions and

directives supported by flat assembler. Directives for defining labels were

already discussed in 1.2.3, all other directives will be described later in

this chapter.

 

 

2.1  The x86 architecture instructions

 

In this section you can find both the information about the syntax and

purpose the assembly language instructions. If you need more technical

information, look for the Intel Architecture Software Developer's Manual.

  Assembly instructions consist of the mnemonic (instruction's name) and from

zero to three operands. If there are two or more operands, usually first is

the destination operand and second is the source operand. Each operand can be

register, memory or immediate value (see 1.2 for details about syntax of

operands). After the description of each instruction there are examples

of different combinations of operands, if the instruction has any.

  Some instructions act as prefixes and can be followed by other instruction

in the same line, and there can be more than one prefix in a line. Each name

of the segment register is also a mnemonic of instruction prefix, altough it

is recommended to use segment overrides inside the square brackets instead of

these prefixes.

 

 

2.1.1  Data movement instructions

 

"mov" transfers a byte, word or double word from the source operand to the

destination operand. It can transfer data between general registers, from

the general register to memory, or from memory to general register, but it

cannot move from memory to memory. It can also transfer an immediate value to

general register or memory, segment register to general register or memory,

general register or memory to segment register, control or debug register to

general register and general register to control or debug register. The "mov"

can be assembled only if the size of source operand and size of destination

operand are the same. Below are the examples for each of the allowed

combinations:

 

    mov bx,ax       ; general register to general register

    mov [char],al   ; general register to memory

    mov bl,[char]   ; memory to general register

    mov dl,32       ; immediate value to general register

    mov [char],32   ; immediate value to memory

    mov ax,ds       ; segment register to general register

    mov [bx],ds     ; segment register to memory

    mov ds,ax       ; general register to segment register

    mov ds,[bx]     ; memory to segment register

    mov eax,cr0     ; control register to general register

    mov cr3,ebx     ; general register to control register

 

  "xchg" swaps the contents of two operands. It can swap two byte operands,

two word operands or two double word operands. Order of operands is not

important. The operands may be two general registers, or general register

with memory. For example:

 

    xchg ax,bx      ; swap two general registers

    xchg al,[char]  ; swap register with memory

 

  "push" decrements the stack frame pointer (ESP register), then transfers

the operand to the top of stack indicated by ESP. The operand can be memory,

general register, segment register or immediate value of word or double word

size. If operand is an immediate value and no size is specified, it is by

default treated as a word value if assembler is in 16-bit mode and as a double

word value if assembler is in 32-bit mode. "pushw" and "pushd" mnemonics are

variants of this instruction that store the values of word or double word size

respectively. If more operands follow in the same line (separated only with

spaces, not commas), compiler will assemble chain of the "push" instructions

with these operands. The examples are with single operands:

 

    push ax         ; store general register

    push es         ; store segment register

    pushw [bx]      ; store memory

    push 1000h      ; store immediate value

 

  "pusha" saves the contents of the eight general register on the stack.

This instruction has no operands. There are two version of this instruction,

one 16-bit and one 32-bit, assembler automatically generates the appropriate

version for current mode, but it can be overridden by using "pushaw" or

"pushad" mnemonic to always get the 16-bit or 32-bit version. The 16-bit

version of this instruction pushes general registers on the stack in the

following order: AX, CX, DX, BX, the initial value of SP before AX was pushed,

BP, SI and DI. The 32-bit version pushes equivalent 32-bit general registers

in the same order.

  "pop" transfers the word or double word at the current top of stack to the

destination operand, and then increments ESP to point to the new top of stack.

The operand can be memory, general register or segment register. "popw" and

"popd" mnemonics are variants of this instruction for restoring the values of

word or double word size respectively. If more operands separated with spaces

follow in the same line, compiler will assemble chain of the "pop"

instructions with these operands.

 

    pop bx          ; restore general register

    pop ds          ; restore segment register

    popw [si]       ; restore memory

 

  "popa" restores the registers saved on the stack by "pusha" instruction,

except for the saved value of SP (or ESP), which is ignored. This instruction

has no operands. To force assembling 16-bit or 32-bit version of this

instruction use "popaw" or "popad" mnemonic.

 

 

2.1.2  Type conversion instructions

 

The type conversion instructions convert bytes into words, words into double

words, and double words into quad words. These conversions can be done using

the sign extension or zero extension. The sign extension fills the extra bits

of the larger item with the value of the sign bit of the smaller item, the

zero extension simply fills them with zeros.

  "cwd" and "cdq" double the size of value AX or EAX register respectively

and store the extra bits into the DX or EDX register. The conversion is done

using the sign extension. These instructions have no operands.

  "cbw" extends the sign of the byte in AL throughout AX, and "cwde" extends

the sign of the word in AX throughout EAX. These instructions also have no

operands.

  "movsx" converts a byte to word or double word and a word to double word

using the sign extension. "movzx" does the same, but it uses the zero

extension. The source operand can be general register or memory, while the

destination operand must be a general register. For example:

 

    movsx ax,al         ; byte register to word register

    movsx edx,dl        ; byte register to double word register

    movsx eax,ax        ; word register to double word register

    movsx ax,byte [bx]  ; byte memory to word register

    movsx edx,byte [bx] ; byte memory to double word register

    movsx eax,word [bx] ; word memory to double word register

 

 

2.1.3  Binary arithmetic instructions

 

"add" replaces the destination operand with the sum of the source and

destination operands and sets CF if overflow has occurred. The operands may

be bytes, words or double words. The destination operand can be general

register or memory, the source operand can be general register or immediate

value, it can also be memory if the destination operand is register.

 

    add ax,bx       ; add register to register

    add ax,[si]     ; add memory to register

    add [di],al     ; add register to memory

    add al,48       ; add immediate value to register

    add [char],48   ; add immediate value to memory

 

  "adc" sums the operands, adds one if CF is set, and replaces the destination

operand with the result. Rules for the operands are the same as for the "add"

instruction. An "add" followed by multiple "adc" instructions can be used to

add numbers longer than 32 bits.

  "inc" adds one to the operand, it does not affect CF. The operand can be a

general register or memory, and the size of the operand can be byte, word or

double word.

 

    inc ax          ; increment register by one

    inc byte [bx]   ; increment memory by one

 

  "sub" subtracts the source operand from the destination operand and replaces

the destination operand with the result. If a borrow is required, the CF is

set. Rules for the operands are the same as for the "add" instruction.

  "sbb" subtracts the source operand from the destination operand, subtracts

one if CF is set, and stores the result to the destination operand. Rules for

the operands are the same as for the "add" instruction. A "sub" followed by

multiple "sbb" instructions may be used to subtract numbers longer than 32

bits.

  "dec" subtracts one from the operand, it does not affect CF. Rules for the

operand are the same as for the "inc" instruction.

  "cmp" subtracts the source operand from the destination operand. It updates

the flags as the "sub" instruction, but does not alter the source and

destination operands. Rules for the operands are the same as for the "sub"

instruction.

  "neg" subtracts a signed integer operand from zero. The effect of this

instructon is to reverse the sign of the operand from positive to negative or

from negative to positive. Rules for the operand are the same as for the "inc"

instruction.

  "xadd" exchanges the destination operand with the source operand, then loads

the sum of the two values into the destination operand. The destination operand

may be a general register or memory, the source operand must be a general

register.

  All the above binary arithmetic instructions update SF, ZF, PF and OF flags.

SF is always set to the same value as the result's sign bit, ZF is set when

all the bits of result are zero, PF is set when low order eight bits of result

contain an even number of set bits, OF is set if result is too large for a

positive number or too small for a negative number (excluding sign bit) to fit

in destination operand.

  "mul" performs an unsigned multiplication of the operand and the

accumulator. If the operand is a byte, the processor multiplies it by the

contents of AL and returns the 16-bit result to AH and AL. If the operand is a

word, the processor multiplies it by the contents of AX and returns the 32-bit

result to DX and AX. If the operand is a double word, the processor multiplies

it by the contents of EAX and returns the 64-bit result in EDX and EAX. "mul"

sets CF and OF when the upper half of the result is nonzero, otherwise they

are cleared. Rules for the operand are the same as for the "inc" instruction.

  "imul" performs a signed multiplication operation. This instruction has

three variations. First has one operand and behaves in the same way as the

"mul" instruction. Second has two operands, in this case destination operand

is multiplied by the source operand and the result replaces the destination

operand. Destination operand must be a general register, it can be word or

double word, source operand can be general register, memory or immediate

value. Third form has three operands, the destination operand must be a

general register, word or double word in size, source operand can be general

register or memory, and third operand must be an immediate value. The source

operand is multiplied by the immediate value and the result is stored in the

destination register. All the three forms calculate the product to twice the

size of operands and set CF and OF when the upper half of the result is

nonzero, but second and third form truncate the product to the size of

operands. So second and third forms can be also used for unsigned operands

because, whether the operands are signed or unsigned, the lower half of the

product is the same. Below are the examples for all three forms:

 

    imul bl         ; accumulator by register

    imul word [si]  ; accumulator by memory

    imul bx,cx      ; register by register

    imul bx,[si]    ; register by memory

    imul bx,10      ; register by immediate value

    imul ax,bx,10   ; register by immediate value to register

    imul ax,[si],10 ; memory by immediate value to register

 

  "div" performs an unsigned division of the accumulator by the operand.

The dividend (the accumulator) is twice the size of the divisor (the operand),

the quotient and remainder have the same size as the divisor. If divisor is

byte, the dividend is taken from AX register, the quotient is stored in AL and

the remainder is stored in AH. If divisor is word, the upper half of dividend

is taken from DX, the lower half of dividend is taken from AX, the quotient is

stored in AX and the remainder is stored in DX. If divisor is double word,

the upper half of dividend is taken from EDX, the lower half of dividend is

taken from EAX, the quotient is stored in EAX and the remainder is stored in

EDX. Rules for the operand are the same as for the "mul" instruction.

  "idiv" performs a signed division of the accumulator by the operand.

It uses the same registers as the "div" instruction, and the rules for

the operand are the same.

 

 

2.1.4  Decimal arithmetic instructions

 

Decimal arithmetic is performed by combining the binary arithmetic

instructions (already described in the prior section) with the decimal

arithmetic instructions. The decimal arithmetic instructions are used to

adjust the results of a previous binary arithmetic operation to produce a

valid packed or unpacked decimal result, or to adjust the inputs to a

subsequent binary arithmetic operation so the operation will produce a valid

packed or unpacked decimal result.

  "daa" adjusts the result of adding two valid packed decimal operands in

AL. "daa" must always follow the addition of two pairs of packed decimal

numbers (one digit in each half-byte) to obtain a pair of valid packed

decimal digits as results. The carry flag is set if carry was needed.

This instruction has no operands.

  "das" adjusts the result of subtracting two valid packed decimal operands

in AL. "das" must always follow the subtraction of one pair of packed decimal

numbers (one digit in each half-byte) from another to obtain a pair of valid

packed decimal digits as results. The carry flag is set if a borrow was

needed. This instruction has no operands.

  "aaa" changes the contents of register AL to a valid unpacked decimal

number, and zeroes the top four bits. "aaa" must always follow the addition

of two unpacked decimal operands in AL. The carry flag is set and AH is

incremented if a carry is necessary. This instruction has no operands.

  "aas" changes the contents of register AL to a valid unpacked decimal

number, and zeroes the top four bits. "aas" must always follow the

subtraction of one unpacked decimal operand from another in AL. The carry flag

is set and AH decremented if a borrow is necessary. This instruction has no

operands.

  "aam" corrects the result of a multiplication of two valid unpacked decimal

numbers. "aam" must always follow the multiplication of two decimal numbers

to produce a valid decimal result. The high order digit is left in AH, the

low order digit in AL. The generalized version of this instruction allows

adjustment of the contents of the AX to create two unpacked digits of any

number base. The standard version of this instruction has no operands, the

generalized version has one operand - an immediate value specifying the

number base for the created digits.

  "aad" modifies the numerator in AH and AL to prepare for the division of two

valid unpacked decimal operands so that the quotient produced by the division

will be a valid unpacked decimal number. AH should contain the high order

digit and AL the low order digit. This instruction adjusts the value and

places the result in AL, while AH will contain zero. The generalized version

of this instruction allows adjustment of two unpacked digits of any number

base. Rules for the operand are the same as for the "aam" instruction.

 

 

2.1.5  Logical instructions

 

"not" inverts the bits in the specified operand to form a one's complement

of the operand. It has no effect on the flags. Rules for the operand are the

same as for the "inc" instruction.

  "and", "or" and "xor" instructions perform the standard logical operations.

They update the SF, ZF and PF flags. Rules for the operands are the same as

for the "add" instruction.

  "bt", "bts", "btr" and "btc" instructions operate on a single bit which can

be in memory or in a general register. The location of the bit is specified

as an offset from the low order end of the operand. The value of the offset

is the taken from the second operand, it either may be an immediate byte or

a general register. These instructions first assign the value of the selected

bit to CF. "bt" instruction does nothing more, "bts" sets the selected bit to

1, "btr" resets the selected bit to 0, "btc" changes the bit to its

complement. The first operand can be word or double word.

 

    bt  ax,15        ; test bit in register

    bts word [bx],15 ; test and set bit in memory

    btr ax,cx        ; test and reset bit in register

    btc word [bx],cx ; test and complement bit in memory

 

  "bsf" and "bsr" instructions scan a word or double word for first set bit

and store the index of this bit into destination operand, which must be

general register. The bit string being scanned is specified by source operand,

it may be either general register or memory. The ZF flag is set if the entire

string is zero (no set bits are found); otherwise it is cleared. If no set bit

is found, the value of the destination register is undefined. "bsf" scans from

low order to high order (starting from bit index zero). "bsr" scans from high

order to low order (starting from bit index 15 of a word or index 31 of a

double word).

 

    bsf ax,bx        ; scan register forward

    bsr ax,[si]      ; scan memory reverse

 

  "shl" shifts the destination operand left by the number of bits specified

in the second operand. The destination operand can be byte, word, or double

word general register or memory. The second operand can be an immediate value

or the CL register. The processor shifts zeros in from the right (low order)

side of the operand as bits exit from the left side. The last bit that exited

is stored in CF. "sal" is a synonym for "shl".

 

    shl al,1         ; shift register left by one bit

    shl byte [bx],1  ; shift memory left by one bit

    shl ax,cl        ; shift register left by count from cl

    shl word [bx],cl ; shift memory left by count from cl

 

  "shr" and "sar" shift the destination operand right by the number of bits

specified in the second operand. Rules for operands are the same as for the

"shl" instruction. "shr" shifts zeros in from the left side of the operand as

bits exit from the right side. The last bit that exited is stored in CF.

"sar" preserves the sign of the operand by shifting in zeros on the left side

if the value is positive or by shifting in ones if the value is negative.

  "shld" shifts bits of the destination operand to the left by the number

of bits specified in third operand, while shifting high order bits from the

source operand into the destination operand on the right. The source operand

remains unmodified. The destination operand can be a word or double word

general register or memory, the source operand must be a general register,

third operand can be an immediate value or the CL register.

 

    shld ax,bx,1     ; shift register left by one bit

    shld [di],bx,1   ; shift memory left by one bit

    shld ax,bx,cl    ; shift register left by count from cl

    shld [di],bx,cl  ; shift memory left by count from cl

 

  "shrd" shifts bits of the destination operand to the right, while shifting

low order bits from the source operand into the destination operand on the

left. The source operand remains unmodified. Rules for operands are the same

as for the "shld" instruction.

  "rol" and "rcl" rotate the byte, word or double word destination operand

left by the number of bits specified in the second operand. For each rotation

specified, the high order bit that exits from the left of the operand returns

at the right to become the new low order bit. "rcl" additionally puts in CF

each high order bit that exits from the left side of the operand before it

returns to the operand as the low order bit on the next rotation cycle. Rules

for operands are the same as for the "shl" instruction.

  "ror" and "rcr" rotate the byte, word or double word destination operand

right by the number of bits specified in the second operand. For each rotation

specified, the low order bit that exits from the right of the operand returns

at the left to become the new high order bit. "rcr" additionally puts in CF

each low order bit that exits from the right side of the operand before it

returns to the operand as the high order bit on the next rotation cycle.

Rules for operands are the same as for the "shl" instruction.

  "test" performs the same action as the "and" instruction, but it does not

alter the destination operand, only updates flags. Rules for the operands are

the same as for the "and" instruction.

  "bswap" reverses the byte order of a 32-bit general register: bits 0 through

7 are swapped with bits 24 through 31, and bits 8 through 15 are swapped with

bits 16 through 23. This instruction is provided for converting little-endian

values to big-endian format and vice versa.

 

    bswap edx        ; swap bytes in register

 

 

2.1.6  Control transfer instructions

 

"jmp" unconditionally transfers control to the target location. The

destination address can be specified directly within the instruction or

indirectly through a register or memory, the acceptable size of this address

depends on whether the jump is near or far (it can be specified by preceding

the operand with "near" or "far" operator) and whether the instruction is

16-bit or 32-bit. Operand for near jump should be "word" size for 16-bit

instruction or the "dword" size for 32-bit instruction. Operand for far jump

should be "dword" size for 16-bit instruction or "pword" size for 32-bit

instruction. A direct "jmp" instruction includes the destination address as

part of the instruction (and can be preceded by "short", "near" or "far"

operator), the operand specifying address should be the numerical expression

for near or short jump, or two numerical expressions separated with colon for

far jump, the first specifies selector of segment, the second is the offset

within segment. The "pword" operator can be used to force the 32-bit far call,

and "dword" to force the 16-bit far call. An indirect "jmp" instruction

obtains the destination address indirectly through a register or a pointer

variable, the operand should be general register or memory. See also 1.2.5 for

some more details.

 

    jmp 100h         ; direct near jump

    jmp 0FFFFh:0     ; direct far jump

    jmp ax           ; indirect near jump

    jmp pword [ebx]  ; indirect far jump

 

  "call" transfers control to the procedure, saving on the stack the address

of the instruction following the "call" for later use by a "ret" (return)

instruction. Rules for the operands are the same as for the "jmp" instruction,

but the "call" has no short variant of direct instruction and thus it not

optimized.

  "ret", "retn" and "retf" instructions terminate the execution of a procedure

and transfers control back to the program that originally invoked the

procedure using the address that was stored on the stack by the "call"

instruction. "ret" is the equivalent for "retn", which returns from the

procedure that was executed using the near call, while "retf" returns from

the procedure that was executed using the far call. These instructions default

to the size of address appropriate for the current code setting, but the size

of address can be forced to 16-bit by using the "retw", "retnw" and "retfw"

mnemonics, and to 32-bit by using the "retd", "retnd" and "retfd" mnemonics.

All these instructions may optionally specify an immediate operand, by adding

this constant to the stack pointer, they effectively remove any arguments that

the calling program pushed on the stack before the execution of the "call"

instruction.

  "iret" returns control to an interrupted procedure. It differs from "ret" in

that it also pops the flags from the stack into the flags register. The flags

are stored on the stack by the interrupt mechanism. It defaults to the size of

return address appropriate for the current code setting, but it can be forced

to use 16-bit or 32-bit address by using the "iretw" or "iretd" mnemonic.

  The conditional transfer instructions are jumps that may or may not transfer

control, depending on the state of the CPU flags when the instruction

executes. The mnemonics for conditional jumps may be obtained by attaching

the condition mnemonic (see table 2.1) to the "j" mnemonic,

for example "jc" instruction will transfer the control when the CF flag is

set. The conditional jumps can be short or near, and direct only, and can be

optimized (see 1.2.5), the operand should be an immediate value specifying

target address.

 

   Table 2.1  Conditions

  ÚÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿

  ³ Mnemonic ³ Condition tested      ³ Description            ³

  ÆÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͵

  ³ o        ³ OF = 1                ³ overflow               ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ no       ³ OF = 0                ³ not overflow           ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ c        ³                       ³ carry                  ³

  ³ b        ³ CF = 1                ³ below                  ³

  ³ nae      ³                       ³ not above nor equal    ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ nc       ³                       ³ not carry              ³

  ³ ae       ³ CF = 0                ³ above or equal         ³

  ³ nb       ³                       ³ not below              ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ e        ³ ZF = 1                ³ equal                  ³

  ³ z        ³                       ³ zero                   ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ ne       ³ ZF = 0                ³ not equal              ³

  ³ nz       ³                       ³ not zero               ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ be       ³ CF or ZF = 1          ³ below or equal         ³

  ³ na       ³                       ³ not above              ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ a        ³ CF or ZF = 0          ³ above                  ³

  ³ nbe      ³                       ³ not below nor equal    ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ s        ³ SF = 1                ³ sign                   ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ ns       ³ SF = 0                ³ not sign               ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ p        ³ PF = 1                ³ parity                 ³

  ³ pe       ³                       ³ parity even            ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ np       ³ PF = 0                ³ not parity             ³

  ³ po       ³                       ³ parity odd             ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ l        ³ SF xor OF = 1         ³ less                   ³

  ³ nge      ³                       ³ not greater nor equal  ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ ge       ³ SF xor OF = 0         ³ greater or equal       ³

  ³ nl       ³                       ³ not less               ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ le       ³ (SF xor OF) or ZF = 1 ³ less or equal          ³

  ³ ng       ³                       ³ not greater            ³

  ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ g        ³ (SF xor OF) or ZF = 0 ³ greater                ³

  ³ nle      ³                       ³ not less nor equal     ³

  ÀÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

 

  The "loop" instructions are conditional jumps that use a value placed in

CX (or ECX) to specify the number of repetitions of a software loop. All

"loop" instructions automatically decrement CX (or ECX) and terminate the

loop (don't transfer the control) when CX (or ECX) is zero. It uses CX or ECX

whether the current code setting is 16-bit or 32-bit, but it can be forced to

us CX with the "loopw" mnemonic or to use ECX with the "loopd" mnemonic.

"loope" and "loopz" are the synonyms for the same instruction, which acts as

the standard "loop", but also terminates the loop when ZF flag is set.

"loopew" and "loopzw" mnemonics force them to use CX register while "looped"

and "loopzd" force them to use ECX register. "loopne" and "loopnz" are the

synonyms for the same instructions, which acts as the standard "loop", but

also terminate the loop when ZF flag is not set. "loopnew" and "loopnzw"

mnemonics force them to use CX register while "loopned" and "loopnzd" force

them to use ECX register. Every "loop" instruction needs an operand being an

immediate value specifying target address, it can be only short jump (in the

range of 128 bytes back and 127 bytes forward from the address of instruction

following the "loop" instruction).

  "jcxz" branches to the label specified in the instruction if it finds a

value of zero in CX, "jecxz" does the same, but checks the value of ECX

instead of CX. Rules for the operands are the same as for the "loop"

instruction.

  "int" activates the interrupt service routine that corresponds to the

number specified as an operand to the instruction, the number should be in

range from 0 to 255. The interrupt service routine terminates with an "iret"

instruction that returns control to the instruction that follows "int".

"int3" mnemonic codes the short (one byte) trap that invokes the interrupt 3.

"into" instruction invokes the interrupt 4 if the OF flag is set.

  "bound" verifies that the signed value contained in the specified register

lies within specified limits. An interrupt 5 occurs if the value contained in

the register is less than the lower bound or greater than the upper bound. It

needs two operands, the first operand specifies the register being tested,

the second operand should be memory address for the two signed limit values.

The operands can be "word" or "dword" in size.

 

    bound ax,[bx]    ; check word for bounds

    bound eax,[esi]  ; check double word for bounds

 

 

2.1.7  I/O instructions

 

  "in" transfers a byte, word, or double word from an input port to AL, AX,

or EAX. I/O ports can be addressed either directly, with the immediate byte

value coded in instruction, or indirectly via the DX register. The destination

operand should be AL, AX, or EAX register. The source operand should be an

immediate value in range from 0 to 255, or DX register.

 

    in al,20h        ; input byte from port 20h

    in ax,dx         ; input word from port addressed by dx

 

  "out" transfers a byte, word, or double word to an output port from AL, AX,

or EAX. The program can specify the number of the port using the same methods

as the "in" instruction. The destination operand should be an immediate value

in range from 0 to 255, or DX register. The source operand should be AL, AX,

or EAX register.

 

    out 20h,ax       ; output word to port 20h

    out dx,al        ; output byte to port addressed by dx

 

 

2.1.8  Strings operations

 

The string operations operate on one element of a string. A string element

may be a byte, a word, or a double word. The string elements are addressed by

SI and DI (or ESI and EDI) registers. After every string operation SI and/or

DI (or ESI and/or EDI) are automatically updated to point to the next element

of the string. If DF (direction flag) is zero, the index registers are

incremented, if DF is one, they are decremented. The amount of the increment

or decrement is 1, 2, or 4 depending on the size of the string element. Every

string operation instruction has short forms which have no operands and use

SI and/or DI when the code type is 16-bit, and ESI and/or EDI when the code

type is 32-bit. SI and ESI by default address data in the segment selected

by DS, DI and EDI always address data in the segment selected by ES. Short

form is obtained by attaching to the mnemonic of string operation letter

specifying the size of string element, it should be "b" for byte element,

"w" for word element, and "d" for double word element. Full form of string

operation needs operands providing the size operator and the memory addresses,

which can be SI or ESI with any segment prefix, DI or EDI always with ES

segment prefix.

  "movs" transfers the string element pointed to by SI (or ESI) to the

location pointed to by DI (or EDI). Size of operands can be byte, word, or

double word. The destination operand should be memory addressed by DI or EDI,

the source operand should be memory addressed by SI or ESI with any segment

prefix.

 

    movs byte [di],[si]        ; transfer byte

    movs word [es:di],[ss:si]  ; transfer word

    movsd                      ; transfer double word

 

  "cmps" subtracts the destination string element from the source string

element and updates the flags AF, SF, PF, CF and OF, but it does not change

any of the compared elements. If the string elements are equal, ZF is set,

otherwise it is cleared. The first operand for this instruction should be the

source string element addressed by SI or ESI with any segment prefix, the

second operand should be the destination string element addressed by DI or

EDI.

 

    cmpsb                      ; compare bytes

    cmps word [ds:si],[es:di]  ; compare words

    cmps dword [fs:esi],[edi]  ; compare double words

 

  "scas" subtracts the destination string element from AL, AX, or EAX

(depending on the size of string element) and updates the flags AF, SF, ZF,

PF, CF and OF. If the values are equal, ZF is set, otherwise it is cleared.

The operand should be the destination string element addressed by DI or EDI.

 

    scas byte [es:di]          ; scan byte

    scasw                      ; scan word

    scas dword [es:edi]        ; scan double word

 

  "stos" places the value of AL, AX, or EAX into the destination string

element. Rules for the operand are the same as for the "scas" instruction.

  "lods" places the source string element into AL, AX, or EAX. The operand

should be the source string element addressed by SI or ESI with any segment

prefix.

 

    lods byte [ds:si]          ; load byte

    lods word [cs:si]          ; load word

    lodsd                      ; load double word

 

  "ins" transfers a byte, word, or double word from an input port addressed

by DX register to the destination string element. The destination operand

should be memory addressed by DI or EDI, the source operand should be the DX

register.

 

    insb                       ; input byte

    ins word [es:di],dx        ; input word

    ins dword [edi],dx         ; input double word

 

  "outs" transfers the source string element to an output port addressed by

DX register. The destination operand should be the DX register and the source

operand should be memory addressed by SI or ESI with any segment prefix.

 

    outs dx,byte [si]          ; output byte

    outsw                      ; output word

    outs dx,dword [gs:esi]     ; output double word

 

  The repeat prefixes "rep", "repe"/"repz", and "repne"/"repnz" specify

repeated string operation. When a string operation instruction has a repeat

prefix, the operation is executed repeatedly, each time using a different

element of the string. The repetition terminates when one of the conditions

specified by the prefix is satisfied. All three prefixes automatically

decrease CX or ECX register (depending whether string operation instruction

uses the 16-bit or 32-bit addressing) after each operation and repeat the

associated operation until CX or ECX is zero. "repe"/"repz" and

"repne"/"repnz" are used exclusively with the "scas" and "cmps" instructions

(described below). When these prefixes are used, repetition of the next

instruction depends on the zero flag (ZF) also, "repe" and "repz" terminate

the execution when the ZF is zero, "repne" and "repnz" terminate the execution

when the ZF is set.

 

    rep  movsd       ; transfer multiple double words

    repe cmpsb       ; compare bytes until not equal

 

 

2.1.9  Flag control instructions

 

The flag control instructions provide a method for directly changing the

state of bits in the flag register. All instructions described in this

section have no operands.

  "stc" sets the CF (carry flag) to 1, "clc" zeroes the CF, "cmc" changes the

CF to its complement. "std" sets the DF (direction flag) to 1, "cld" zeroes

the DF, "sti" sets the IF (interrupt flag) to 1 and therefore enables the

interrupts, "cli" zeroes the IF and therefore disables the interrupts.

  "lahf" copies SF, ZF, AF, PF, and CF to bits 7, 6, 4, 2, and 0 of the

AH register. The contents of the remaining bits are undefined. The flags

remain unaffected.

  "sahf" transfers bits 7, 6, 4, 2, and 0 from the AH register into SF, ZF,

AF, PF, and CF.

  "pushf" decrements "esp" by two or four and stores the low word or

double word of flags register at the top of stack, size of stored data

depends on the current code setting. "pushfw" variant forces storing the

word and "pushfd" forces storing the double word.

  "popf" transfers specific bits from the word or double word at the top

of stack, then increments "esp" by two or four, this value depends on

the current code setting. "popfw" variant forces restoring from the word

and "popfd" forces restoring from the double word.

 

 

2.1.10  Conditional operations

 

  The instructions obtained by attaching the condition mnemonic (see table

2.1) to the "set" mnemonic set a byte to one if the condition is true and set

the byte to zero otherwise. The operand should be an 8-bit be general register

or the byte in memory.

 

    setne al         ; set al if zero flag cleared

    seto byte [bx]   ; set byte if overflow

 

  "salc" instruction sets the all bits of AL register when the carry flag is

set and zeroes the AL register otherwise. This instruction has no arguments.

  The instructions obtained by attaching the condition mnemonic to "cmov"

mnemonic transfer the word or double word from the general register or memory

to the general register only when the condition is true. The destination

operand should be general register, the source operand can be general register

or memory.

 

    cmove ax,bx      ; move when zero flag set

    cmovnc eax,[ebx] ; move when carry flag cleared

 

  "cmpxchg" compares the value in the AL, AX, or EAX register with the

destination operand. If the two values are equal, the source operand is

loaded into the destination operand. Otherwise, the destination operand is

loaded into the AL, AX, or EAX register. The destination operand may be a

general register or memory, the source operand must be a general register.

 

    cmpxchg dl,bl    ; compare and exchange with register

    cmpxchg [bx],dx  ; compare and exchange with memory

 

  "cmpxchg8b" compares the 64-bit value in EDX and EAX registers with the

destination operand. If the values are equal, the 64-bit value in ECX and EBX

registers is stored in the destination operand. Otherwise, the value in the

destination operand is loaded into EDX and EAX registers. The destination

operand should be a quad word in memory.

 

    cmpxchg8b [bx]   ; compare and exchange 8 bytes

 

 

2.1.11  Miscellaneous instructions

 

"nop" instruction occupies one byte but affects nothing but the instruction

pointer. This instruction has no operands and doesn't perform any operation.

  "ud2" instruction generates an invalid opcode exception. This instruction

is provided for software testing to explicitly generate an invalid opcode.

This is instruction has no operands.

  "xlat" replaces a byte in the AL register with a byte indexed by its value

in a translation table addressed by BX or EBX. The operand should be a byte

memory addressed by BX or EBX with any segment prefix. This instruction has

also a short form "xlatb" which has no operands and uses the BX or EBX address

in the segment selected by DS depending on the current code setting.

  "lds" transfers a pointer variable from the source operand to DS and the

destination register. The source operand must be a memory operand, and the

destination operand must be a general register. The DS register receives the

segment selector of the pointer while the destination register receives the

offset part of the pointer. "les", "lfs", "lgs" and "lss" operate identically

to "lds" except that rather than DS register the ES, FS, GS and SS is used

respectively.

 

    lds bx,[si]      ; load pointer to ds:bx

 

  "lea" transfers the offset of the source operand (rather than its value)

to the destination operand. The source operand must be a memory operand, and

the destination operand must be a general register.

 

    lea dx,[bx+si+1] ; load effective address to dx

 

  "cpuid" returns processor identification and feature information in the

EAX, EBX, ECX, and EDX registers. The information returned is selected by

entering a value in the EAX register before the instruction is executed.

This instruction has no operands.

  "pause" instruction delays the execution of the next instruction an

implementation specific amount of time. It can be used to improve the

performance of spin wait loops. This instruction has no operands.

  "enter" creates a stack frame that may be used to implement the scope rules

of block-structured high-level languages. A "leave" instruction at the end of

a procedure complements an "enter" at the beginning of the procedure to

simplify stack management and to control access to variables for nested

procedures. The "enter" instruction includes two parameters. The first

parameter specifies the number of bytes of dynamic storage to be allocated on

the stack for the routine being entered. The second parameter corresponds to

the lexical nesting level of the routine, it can be in range from 0 to 31.

The specified lexical level determines how many sets of stack frame pointers

the CPU copies into the new stack frame from the preceding frame. This list

of stack frame pointers is sometimes called the display. The first word (or

double word when code is 32-bit) of the display is a pointer to the last stack

frame. This pointer enables a "leave" instruction to reverse the action of the

previous "enter" instruction by effectively discarding the last stack frame.

After "enter" creates the new display for a procedure, it allocates the

dynamic storage space for that procedure by decrementing ESP by the number of

bytes specified in the first parameter. To enable a procedure to address its

display, "enter" leaves BP (or EBP) pointing to the beginning of the new stack

frame. If the lexical level is zero, "enter" pushes BP (or EBP), copies SP to

BP (or ESP to EBP) and then subtracts the first operand from ESP. For nesting

levels greater than zero, the processor pushes additional frame pointers on

the stack before adjusting the stack pointer.

 

    enter 2048,0     ; enter and allocate 2048 bytes on stack

 

 

2.1.12  System instructions

 

"lmsw" loads the operand into the machine status word (bits 0 through 15 of

CR0 register), while "smsw" stores the machine status word into the

destination operand. The operand for both those instructions can be 16-bit

general register or memory, for "smsw" it can also be 32-bit general

register.

 

    lmsw ax          ; load machine status from register

    smsw [bx]        ; store machine status to memory

 

  "lgdt" and "lidt" instructions load the values in operand into the global

descriptor table register or the interrupt descriptor table register

respectively. "sgdt" and "sidt" store the contents of the global descriptor

table register or the interrupt descriptor table register in the destination

operand. The operand should be a 6 bytes in memory.

 

    lgdt [ebx]       ; load global descriptor table

 

  "lldt" loads the operand into the segment selector field of the local

descriptor table register and "sldt" stores the segment selector from the

local descriptor table register in the operand. "ltr" loads the operand into

the segment selector field of the task register and "str" stores the segment

selector from the task register in the operand. Rules for operand are the same

as for the "lmsw" and "smsw" instructions.

  "lar" loads the access rights from the segment descriptor specified by

the selector in source operand into the destination operand and sets the ZF

flag. The destination operand can be a 16-bit or 32-bit general register.

The source operand should be a 16-bit general register or memory.

 

    lar ax,[bx]      ; load access rights into word

    lar eax,dx       ; load access rights into double word

 

  "lsl" loads the segment limit from the segment descriptor specified by the

selector in source operand into the destination operand and sets the ZF flag.

Rules for operand are the same as for the "lar" instruction.

  "verr" and "verw" verify whether the code or data segment specified with

the operand is readable or writable from the current privilege level. The

operand should be a word, it can be general register or memory. If the segment

is accessible and readable (for "verr") or writable (for "verw") the ZF flag

is set, otherwise it's cleared. Rules for operand are the same as for the

"lldt" instruction.

  "arpl" compares the RPL (requestor's privilege level) fields of two segment

selectors. The first operand contains one segment selector and the second

operand contains the other. If the RPL field of the destination operand is

less than the RPL field of the source operand, the ZF flag is set and the RPL

field of the destination operand is increased to match that of the source

operand. Otherwise, the ZF flag is cleared and no change is made to the

destination operand. The destination operand can be a word general register

or memory, the source operand must be a general register.

 

    arpl bx,ax       ; adjust RPL of selector in register

    arpl [bx],ax     ; adjust RPL of selector in memory

 

  "clts" clears the TS (task switched) flag in the CR0 register. This

instruction has no operands.

  "lock" prefix causes the processor's bus-lock signal to be asserted during

execution of the accompanying instruction. In a multiprocessor environment,

the bus-lock signal insures that the processor has exclusive use of any shared

memory while the signal is asserted. The "lock" prefix can be prepended only

to the following instructions and only to those forms of the instructions

where the destination operand is a memory operand: "add", "adc", "and", "btc",

"btr", "bts", "cmpxchg", "cmpxchg8b", "dec", "inc", "neg", "not", "or", "sbb",

"sub", "xor", "xadd" and "xchg". If the "lock" prefix is used with one of

these instructions and the source operand is a memory operand, an undefined

opcode exception may be generated. An undefined opcode exception will also be

generated if the "lock" prefix is used with any instruction not in the above

list. The "xchg" instruction always asserts the bus-lock signal regardless of

the presence or absence of the "lock" prefix.

  "hlt" stops instruction execution and places the processor in a halted

state. An enabled interrupt, a debug exception, the BINIT, INIT or the RESET

signal will resume execution. This instruction has no operands.

  "invlpg" invalidates (flushes) the TLB (translation lookaside buffer) entry

specified with the operand, which should be a memory. The processor determines

the page that contains that address and flushes the TLB entry for that page.

  "rdmsr" loads the contents of a 64-bit MSR (model specific register) of the

address specified in the ECX register into registers EDX and EAX. "wrmsr"

writes the contents of registers EDX and EAX into the 64-bit MSR of the

address specified in the ECX register. "rdtsc" loads the current value of the

processor's time stamp counter from the 64-bit MSR into the EDX and EAX

registers. The processor increments the time stamp counter MSR every clock

cycle and resets it to 0 whenever the processor is reset. "rdpmc" loads the

contents of the 40-bit performance monitoring counter specified in the ECX

register into registers EDX and EAX. These instructions have no operands.

  "wbinvd" writes back all modified cache lines in the processor's internal

cache to main memory and invalidates (flushes) the internal caches. The

instruction then issues a special function bus cycle that directs external

caches to also write back modified data and another bus cycle to indicate that

the external caches should be invalidated. This instruction has no operands.

  "rsm" return program control from the system management mode to the program

that was interrupted when the processor received an SMM interrupt. This

instruction has no operands.

  "sysenter" executes a fast call to a level 0 system procedure, "sysexit"

executes a fast return to level 3 user code. The addresses used by these

instructions are stored in MSRs. These instructions have no operands.

 

 

2.1.13  FPU instructions

 

The FPU (Floating-Point Unit) instructions operate on the floating-point

values in three formats: single precision (32-bit), double precision (64-bit)

and double extended precision (80-bit). The FPU registers form the stack and

each of them holds the double extended precision floating-point value. When

some values are pushed onto the stack or are removed from the top, the FPU

registers are shifted, so ST0 is always the value on the top of FPU stack, ST1

is the first value below the top, etc. The ST0 name has also the synonym ST.

  "fld" pushes the floating-point value onto the FPU register stack. The

operand can be 32-bit, 64-bit or 80-bit memory location or the FPU register,

its value is then loaded onto the top of FPU register stack (the ST0

register) and is automatically converted into the double extended precision

format.

 

    fld dword [bx]   ; load single prevision value from memory

    fld st2          ; push value of st2 onto register stack

 

  "fld1", "fldz", "fldl2t", "fldl2e", "fldpi", "fldlg2" and "fldln2" load the

commonly used contants onto the FPU register stack. The loaded constants are

+1.0, +0.0, lb 10, lb e, pi, lg 2 and ln 2 respectively. These instructions

have no operands.

  "fild" converts the signed integer source operand into double extended

precision floating-point format and pushes the result onto the FPU register

stack. The source operand can be a 16-bit, 32-bit or 64-bit memory location.

 

    fild qword [bx]  ; load 64-bit integer from memory

 

  "fst" copies the value of ST0 register to the destination operand, which

can be 32-bit or 64-bit memory location or another FPU register. "fstp"

performs the same operation as "fst" and then pops the register stack,

getting rid of ST0. "fstp" accepts the same operands as the "fst" instruction

and can also store value in the 80-bit memory.

 

    fst st3          ; copy value of st0 into st3 register

    fstp tword [bx]  ; store value in memory and pop stack

 

  "fist" converts the value in ST0 to a signed integer and stores the result

in the destination operand. The operand can be 16-bit or 32-bit memory

location. "fistp" performs the same operation and then pops the register

stack, it accepts the same operands as the "fist" instruction and can also

store integer value in the 64-bit memory, so it has the same rules for

operands as "fild" instruction.

  "fbld" converts the packed BCD integer into double extended precision

floating-point format and pushes this value onto the FPU stack. "fbstp"

converts the value in ST0 to an 18-digit packed BCD integer, stores the result

in the destination operand, and pops the register stack. The operand should be

an 80-bit memory location.

  "fadd" adds the destination and source operand and stores the sum in the

destination location. The destination operand is always an FPU register, if

the source is a memory location, the destination is ST0 register and only

source operand should be specified. If both operands are FPU registers, at

least one of them should be ST0 register. An operand in memory can be a

32-bit or 64-bit value.

 

    fadd qword [bx]  ; add double precision value to st0

    fadd st2,st0     ; add st0 to st2

 

  "faddp" adds the destination and source operand, stores the sum in the

destination location and then pops the register stack. The destination operand

must be an FPU register and the source operand must be the ST0. When no

operands are specified, ST1 is used as a destination operand.

 

    faddp            ; add st0 to st1 and pop the stack

    faddp st2,st0    ; add st0 to st2 and pop the stack

 

"fiadd" instruction converts an integer source operand into double extended

precision floating-point value and adds it to the destination operand. The

operand should be a 16-bit or 32-bit memory location.

 

    fiadd word [bx]  ; add word integer to st0

 

  "fsub", "fsubr", "fmul", "fdiv", "fdivr" instruction are similar to "fadd",

have the same rules for operands and differ only in the perfomed computation.

"fsub" subtracts the source operand from the destination operand, "fsubr"

subtract the destination operand from the source operand, "fmul" multiplies

the destination and source operands, "fdiv" divides the destination operand by

the source operand and "fdivr" divides the source operand by the destination

operand. "fsubp", "fsubrp", "fmulp", "fdivp", "fdivrp" perform the same

operations and pop the register stack, the rules for operand are the same as

for the "faddp" instruction. "fisub", "fisubr", "fimul", "fidiv", "fidivr"

perform these operations after converting the integer source operand into

floating-point value, they have the same rules for operands as "fiadd"

instruction.

  "fsqrt" computes the square root of the value in ST0 register, "fsin"

computes the sine of that value, "fcos" computes the cosine of that value,

"fchs" complements its sign bit, "fabs" clears its sign to create the absolute

value, "frndint" rounds it to the nearest integral value, depending on the

current rounding mode. "f2xm1" computes the exponential value of 2 to the

power of ST0 and subtracts the 1.0 from it, the value of ST0 must lie in the

range -1.0 to +1.0. All these instructions store the result in ST0 and have no

operands.

  "fsincos" computes both the sine and the cosine of the value in ST0

register, stores the sine in ST0 and pushes the cosine on the top of FPU

register stack. "fptan" computes the tangent of the value in ST0, stores the

result in ST0 and pushes a 1.0 onto the FPU register stack. "fpatan" computes

the arctangent of the value in ST1 divided by the value in ST0, stores the

result in ST1 and pops the FPU register stack. "fyl2x" computes the binary

logarithm of ST0, multiplies it by ST1, stores the result in ST1 and pops the

FPU register stack; "fyl2xp1" performs the same operation but it adds 1.0 to

ST0 before computing the logarithm. "fprem" computes the remainder obtained

from dividing the value in ST0 by the value in ST1, and stores the result

in ST0. "fprem1" performs the same operation as "fprem", but it computes the

remainder in the way specified by IEEE Standard 754. "fscale" truncates the

value in ST1 and increases the exponent of ST0 by this value. "fxtract"

separates the value in ST0 into its exponent and significand, stores the

exponent in ST0 and pushes the significand onto the register stack. "fnop"

performs no operation. These instructions have no operands.

  "fxch" exchanges the contents of ST0 an another FPU register. The operand

should be an FPU register, if no operand is specified, the contents of ST0 and

ST1 are exchanged.

  "fcom" and "fcomp" compare the contents of ST0 and the source operand and

set flags in the FPU status word according to the results. "fcomp"

additionally pops the register stack after performing the comparison. The

operand can be a single or double precision value in memory or the FPU

register. When no operand is specified, ST1 is used as a source operand.

 

    fcom             ; compare st0 with st1

    fcomp st2        ; compare st0 with st2 and pop stack

 

  "fcompp" compares the contents of ST0 and ST1, sets flags in the FPU status

word according to the results and pops the register stack twice. This

instruction has no operands.

  "fucom", "fucomp" and "fucompp" performs an unordered comparison of two FPU

registers. Rules for operands are the same as for the "fcom", "fcomp" and

"fcompp", but the source operand must be an FPU register.

  "ficom" and "ficomp" compare the value in ST0 with an integer source operand

and set the flags in the FPU status word according to the results. "ficomp"

additionally pops the register stack after performing the comparison. The

integer value is converted to double extended precision floating-point format

before the comparison is made. The operand should be a 16-bit or 32-bit

memory location.

 

    ficom word [bx]  ; compare st0 with 16-bit integer

 

  "fcomi", "fcomip", "fucomi", "fucomip" perform the comparison of ST0 with

another FPU register and set the ZF, PF and CF flags according to the results.

"fcomip" and "fucomip" additionaly pop the register stack after performing the

comparison. The instructions obtained by attaching the FPU condition mnemonic

(see table 2.2) to the "fcmov" mnemonic transfer the specified FPU register

into ST0 register if the given test condition is true. These instructions

allow two different syntaxes, one with single operand specifying the source

FPU register, and one with two operands, in that case destination operand

should be ST0 register and the second operand specifies the source FPU

register.

 

    fcomi st2        ; compare st0 with st2 and set flags

    fcmovb st0,st2   ; transfer st2 to st0 if below

 

   Table 2.2  FPU conditions

  ÚÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿

  ³ Mnemonic ³ Condition tested ³ Description            ³

  ÆÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͵

  ³ b        ³ CF = 1           ³ below                  ³

  ³ e        ³ ZF = 1           ³ equal                  ³

  ³ be       ³ CF or ZF = 1     ³ below or equal         ³

  ³ u        ³ PF = 1           ³ unordered              ³

  ³ nb       ³ CF = 0           ³ not below              ³

  ³ ne       ³ ZF = 0           ³ not equal              ³

  ³ nbe      ³ CF and ZF = 0    ³ not below nor equal    ³

  ³ nu       ³ PF = 0           ³ not unordered          ³

  ÀÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

 

  "ftst" compares the value in ST0 with 0.0 and sets the flags in the FPU

status word according to the results. "fxam" examines the contents of the ST0

and sets the flags in FPU status word to indicate the class of value in the

register. These instructions have no operands.

  "fstsw" and "fnstsw" store the current value of the FPU status word in the

destination location. The destination operand can be either a 16-bit memory or

the AX register. "fstsw" checks for pending unmasked FPU exceptions before

storing the status word, "fnstsw" does not.

  "fstcw" and "fnstcw" store the current value of the FPU control word at the

specified destination in memory. "fstcw" checks for pending umasked FPU

exceptions before storing the control word, "fnstcw" does not. "fldcw" loads

the operand into the FPU control word. The operand should be a 16-bit memory

location.

  "fstenv" and "fnstenv" store the current FPU operating environment at the

memory location specified with the destination operand, and then mask all FPU

exceptions. "fstenv" checks for pending umasked FPU exceptions before

proceeding, "fnstenv" does not. "fldenv" loads the complete operating

environment from memory into the FPU. "fsave" and "fnsave" store the current

FPU state (operating environment and register stack) at the specified

destination in memory and reinitializes the FPU. "fsave" check for pending

unmasked FPU exceptions before proceeding, "fnsave" does not. "frstor"

loads the FPU state from the specified memory location. All these instructions

need an operand being a memory location. For each of these instructions

exist two additional mnemonics that allow to precisely select the type of the

operation. The "fstenvw", "fnstenvw", "fldenvw", "fsavew", "fnsavew" and

"frstorw" mnemonics force the instruction to perform operation as in the 16-bit

mode, while "fstenvd", "fnstenvd", "fldenvd", "fsaved", "fnsaved" and "frstord"

force the operation as in 32-bit mode.

  "finit" and "fninit" set the FPU operating environment into its default

state. "finit" checks for pending unmasked FPU exception before proceeding,

"fninit" does not. "fclex" and "fnclex" clear the FPU exception flags in the

FPU status word. "fclex" checks for pending unmasked FPU exception before

proceeding, "fnclex" does not. "wait" and "fwait" are synonyms for the same

instruction, which causes the processor to check for pending unmasked FPU

exceptions and handle them before proceeding. These instructions have no

operands.

  "ffree" sets the tag associated with specified FPU register to empty. The

operand should be an FPU register.

  "fincstp" and "fdecstp" rotate the FPU stack by one by adding or

subtracting one to the pointer of the top of stack. These instructions have no

operands.

 

 

2.1.14  MMX instructions

 

The MMX instructions operate on the packed integer types and use the MMX

registers, which are the low 64-bit parts of the 80-bit FPU registers. Because

of this MMX instructions cannot be used at the same time as FPU instructions.

They can operate on packed bytes (eight 8-bit integers), packed words (four

16-bit integers) or packed double words (two 32-bit integers), use of packed

formats allows to perform operations on multiple data at one time.

  "movq" copies a quad word from the source operand to the destination

operand. At least one of the operands must be a MMX register, the second one

can be also a MMX register or 64-bit memory location.

 

    movq mm0,mm1     ; move quad word from register to register

    movq mm2,[ebx]   ; move quad word from memory to register

 

  "movd" copies a double word from the source operand to the destination

operand. One of the operands must be a MMX register, the second one can be a

general register or 32-bit memory location. Only low double word of MMX

register is used.

  All general MMX operations have two operands, the destination operand should

be a MMX register, the source operand can be a MMX register or 64-bit memory

location. Operation is performed on the corresponding data elements of the

source and destination operand and stored in the data elements of the

destination operand. "paddb", "paddw" and "paddd" perform the addition of

packed bytes, packed words, or packed double words.  "psubb", "psubw" and

"psubd" perform the subtraction of appropriate types. "paddsb", "paddsw",

"psubsb" and "psubsw" perform the addition or subtraction of packed bytes

or packed words with the signed saturation. "paddusb", "paddusw", "psubusb",

"psubusw" are analoguous, but with unsigned saturation. "pmulhw" and "pmullw"

performs a signed multiplication of the packed words and store the high or low

words of the results in the destination operand. "pmaddwd" performs a multiply

of the packed words and adds the four intermediate double word products in

pairs to produce result as a packed double words. "pand", "por" and "pxor"

perform the logical operations on the quad words, "pandn" peforms also a

logical negation of the destination operand before performing the "and"

operation. "pcmpeqb", "pcmpeqw" and "pcmpeqd" compare for equality of packed

bytes, packed words or packed double words. If a pair of data elements is

equal, the corresponding data element in the destination operand is filled with

bits of value 1, otherwise it's set to 0. "pcmpgtb", "pcmpgtw" and "pcmpgtd"

perform the similar operation, but they check whether the data elements in the

destination operand are greater than the correspoding data elements in the

source operand. "packsswb" converts packed signed words into packed signed

bytes, "packssdw" converts packed signed double words into packed signed

words, using saturation to handle overflow conditions. "packuswb" converts

packed signed words into packed unsigned bytes. Converted data elements from

the source operand are stored in the high part of the destination operand,

while converted data elements from the destination operand are stored in the

low part. "punpckhbw", "punpckhwd" and "punpckhdq" interleaves the data

elements from the high parts of the source and destination operands and

stores the result into the destination operand. "punpcklbw", "punpcklwd" and

"punpckldq" perform the same operation, but the low parts of the source and

destination operand are used.

 

    paddsb mm0,[esi] ; add packed bytes with signed saturation

    pcmpeqw mm3,mm7  ; compare packed words for equality

 

  "psllw", "pslld" and "psllq" perform logical shift left of the packed words,

packed double words or a single quad word in the destination operand by the

amount specified in the source operand. "psrlw", "psrld" and "psrlq" perform

logical shift right of the packed words, packed double words or a single quad

word. "psraw" and "psrad" perform arithmetic shift of the packed words or

double words. The destination operand should be a MMX register, while source

operand can be a MMX register, 64-bit memory location, or 8-bit immediate

value.

 

    psllw mm2,mm4    ; shift words left logically

    psrad mm4,[ebx]  ; shift double words right arithmetically

 

  "emms" makes the FPU registers usable for the FPU instructions, it must be

used before using the FPU instructions if any MMX instructions were used.

 

 

2.1.15  SSE instructions

 

The SSE extension adds more MMX instructions and also introduces the

operations on packed single precision floating point values. The 128-bit

packed single precision format consists of four single precision floating

point values. The 128-bit SSE registers are designed for the purpose of

operations on this data type.

  "movaps" and "movups" transfer a double quad word operand containing packed

single precision values from source operand to destination operand. At least

one of the operands have to be a SSE register, the second one can be also a

SSE register or 128-bit memory location. Memory operands for "movaps"

instruction must be aligned on boundary of 16 bytes, operands for "movups"

instruction don't have to be aligned.

 

    movups xmm0,[ebx]  ; move unaligned double quad word

 

  "movlps" moves packed two single precision values between the memory and the

low quad word of SSE register. "movhps" moved packed two single precision

values between the memory and the high quad word of SSE register. One of the

operands must be a SSE register, and the other operand must be a 64-bit memory

location.

 

    movlps xmm0,[ebx]  ; move memory to low quad word of xmm0

    movhps [esi],xmm7  ; move high quad word of xmm7 to memory

 

  "movlhps" moves packed two single precision values from the low quad word

of source register to the high quad word of destination register. "movhlps"

moves two packed single precision values from the high quad word of source

register to the low quad word of destination register. Both operands have to

be a SSE registers.

  "movmskps" transfers the most significant bit of each of the four single

precision values in the SSE register into low four bits of a general register.

The source operand must be a SSE register, the destination operand must be a

general register.

  "movss" transfers a single precision value between source and destination

operand (only the low double word is trasferred). At least one of the operands

have to be a SSE register, the second one can be also a SSE register or 32-bit

memory location.

 

    movss [edi],xmm3   ; move low double word of xmm3 to memory

 

  Each of the SSE arithmetic operations has two variants. When the mnemonic

ends with "ps", the source operand can be a 128-bit memory location or a SSE

register, the destination operand must be a SSE register and the operation is

performed on packed four single precision values, for each pair of the

corresponding data elements separately, the result is stored in the

destination register. When the mnemonic ends with "ss", the source operand

can be a 32-bit memory location or a SSE register, the destination operand

must be a SSE register and the operation is performed on single precision

values, only low double words of SSE registers are used in this case, the

result is stored in the low double word of destination register. "addps" and

"addss" add the values, "subps" and "subss" subtract the source value from

destination value, "mulps" and "mulss" multiply the values, "divps" and

"divss" divide the destination value by the source value, "rcpps" and "rcpss"

compute the approximate reciprocal of the source value, "sqrtps" and "sqrtss"

compute the square root of the source value, "rsqrtps" and "rsqrtss" compute

the approximate reciprocal of square root of the source value, "maxps" and

"maxss" compare the source and destination values and return the greater one,

"minps" and "minss" compare the source and destination values and return the

lesser one.

 

    mulss xmm0,[ebx]   ; multiply single precision values

    addps xmm3,xmm7    ; add packed single precision values

 

  "andps", "andnps", "orps" and "xorps" perform the logical operations on

packed single precision values. The source operand can be a 128-bit memory

location or a SSE register, the destination operand must be a SSE register.

  "cmpps" compares packed single precision values and returns a mask result

into the destination operand, which must be a SSE register. The source operand

can be a 128-bit memory location or SSE register, the third operand must be an

immediate operand selecting code of one of the eight compare conditions

(table 2.3). "cmpss" performs the same operation on single precision values,

only low double word of destination register is affected, in this case source

operand can be a 32-bit memory location or SSE register. These two

instructions have also variants with only two operands and the condition

encoded within mnemonic. Their mnemonics are obtained by attaching the

mnemonic from table 2.3 to the "cmp" mnemonic and then attaching the "ps" or

"ss" at the end.

 

    cmpps xmm2,xmm4,0  ; compare packed single precision values

    cmpltss xmm0,[ebx] ; compare single precision values

 

   Table 2.3  SSE conditions

  ÚÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿

  ³ Code ³ Mnemonic ³ Description             ³

  ÆÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͵

  ³ 0    ³ eq       ³ equal                   ³

  ³ 1    ³ lt       ³ less than               ³

  ³ 2    ³ le       ³ less than or equal      ³

  ³ 3    ³ unord    ³ unordered               ³

  ³ 4    ³ neq      ³ not equal               ³

  ³ 5    ³ nlt      ³ not less than           ³

  ³ 6    ³ nle      ³ not less than nor equal ³

  ³ 7    ³ ord      ³ ordered                 ³

  ÀÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

 

  "comiss" and "ucomiss" compare the single precision values and set the ZF,

PF and CF flags to show the result. The destination operand must be a SSE

register, the source operand can be a 32-bit memory location or SSE register.

  "shufps" moves any two of the four single precision values from the

destination operand into the low quad word of the destination operand, and any

two of the four values from the source operand into the high quad word of the

destination operand. The destination operand must be a SSE register, the

source operand can be a 128-bit memory location or SSE register, the third

operand must be an 8-bit immediate value selecting which values will be moved

into the destination operand. Bits 0 and 1 select the value to be moved from

destination operand to the low double word of the result, bits 2 and 3 select

the value to be moved from the destination operand to the second double word,

bits 4 and 5 select the value to be moved from the source operand to the third

double word, and bits 6 and 7 select the value to be moved from the source

operand to the high double word of the result.

 

    shufps xmm0,xmm0,10010011b ; shuffle double words

 

  "unpckhps" performs an interleaved unpack of the values from the high parts

of the source and destination operands and stores the result in the

destination operand, which must be a SSE register. The source operand can be

a 128-bit memory location or a SSE register. "unpcklps" performs an

interleaved unpack of the values from the low parts of the source and

destination operand and stores the result in the destination operand,

the rules for operands are the same.

  "cvtpi2ps" converts packed two double word integers into the the packed two

single precision floating point values and stores the result in the low quad

word of the destination operand, which should be a SSE register. The source

operand can be a 64-bit memory location or MMX register.

 

    cvtpi2ps xmm0,mm0  ; convert integers to single precision values

 

  "cvtsi2ss" converts a double word integer into a single precision floating

point value and stores the result in the low double word of the destination

operand, which should be a SSE register. The source operand can be a 32-bit

memory location or 32-bit general register.

 

    cvtsi2ss xmm0,eax  ; convert integer to single precision value

 

  "cvtps2pi" converts packed two single precision floating point values into

packed two double word integers and stores the result in the destination

operand, which should be a MMX register. The source operand can be a 64-bit

memory location or SSE register, only low quad word of SSE register is used.

"cvttps2pi" performs the similar operation, except that truncation is used to

round a source values to integers, rules for the operands are the same.

 

    cvtps2pi mm0,xmm0  ; convert single precision values to integers

 

  "cvtss2si" convert a single precision floating point value into a double

word integer and stores the result in the destination operand, which should be

a 32-bit general register. The source operand can be a 32-bit memory location

or SSE register, only low double word of SSE register is used. "cvttss2si"

performs the similar operation, except that truncation is used to round a

source value to integer, rules for the operands are the same.

 

    cvtss2si eax,xmm0  ; convert single precision value to integer

 

  "pextrw" copies the word in the source operand specified by the third

operand to the destination operand. The source operand must be a MMX register,

the destination operand must be a 32-bit general register (the high word of

the destination is cleared), the third operand must an 8-bit immediate value.

 

    pextrw eax,mm0,1   ; extract word into eax

 

  "pinsrw" inserts a word from the source operand in the destination operand

at the location specified with the third operand, which must be an 8-bit

immediate value. The destination operand must be a MMX register, the source

operand can be a 16-bit memory location or 32-bit general register (only low

word of the register is used).

 

    pinsrw mm1,ebx,2   ; insert word from ebx

 

  "pavgb" and "pavgw" compute average of packed bytes or words. "pmaxub"

return the maximum values of packed unsigned bytes, "pminub" returns the

minimum values of packed unsigned bytes, "pmaxsw" returns the maximum values

of packed signed words, "pminsw" returns the minimum values of packed signed

words. "pmulhuw" performs a unsigned multiplication of the packed words and

stores the high words of the results in the destination operand. "psadbw"

computes the absolute differences of packed unsigned bytes, sums the

differences, and stores the sum in the low word of destination operand. All

these instructions follow the same rules for operands as the general MMX

operations described in previous section.

  "pmovmskb" creates a mask made of the most significant bit of each byte in

the source operand and stores the result in the low byte of destination

operand. The source operand must be a MMX register, the destination operand

must a 32-bit general register.

  "pshufw" inserts words from the source operand in the destination operand

from the locations specified with the third operand. The destination operand

must be a MMX register, the source operand can be a 64-bit memory location or

MMX register, third operand must an 8-bit immediate value selecting which

values will be moved into destination operand, in the similar way as the third

operand of the "shufps" instruction.

  "movntq" moves the quad word from the source operand to memory using a

non-temporal hint to minimize cache pollution. The source operand should be a

MMX register, the destination operand should be a 64-bit memory location.

"movntps" stores packed single precision values from the SSE register to

memory using a non-temporal hint. The source operand should be a SSE register,

the destination operand should be a 128-bit memory location. "maskmovq" stores

selected bytes from the first operand into a 64-bit memory location using a

non-temporal hint. Both operands should be a MMX registers, the second operand

selects wich bytes from the source operand are written to memory. The

memory location is pointed by DI (or EDI) register in the segment selected

by DS.

  "prefetcht0", "prefetcht1", "prefetcht2" and "prefetchnta" fetch the line

of data from memory that contains byte specified with the operand to a

specified location in hierarchy.  The operand should be an 8-bit memory

location.

  "sfence" performs a serializing operation on all instruction storing to

memory that were issued prior to it. This instruction has no operands.

  "ldmxcsr" loads the 32-bit memory operand into the MXCSR register. "stmxcsr"

stores the contents of MXCSR into a 32-bit memory operand.

  "fxsave" saves the current state of the FPU, MXCSR register, and all the FPU

and SSE registers to a 512-byte memory location specified in the destination

operand. "fxrstor" reloads data previously stored with "fxsave" instruction

from the specified 512-byte memory location. The memory operand for both those

instructions must be aligned on 16 byte boundary, it should declare operand

of no specified size.

 

 

2.1.16  SSE2 instructions

 

The SSE2 extension introduces the operations on packed double precision

floating point values, extends the syntax of MMX instructions, and adds also

some new instructions.

  "movapd" and "movupd" transfer a double quad word operand containing packed

double precision values from source operand to destination operand. These

instructions are analogous to "movaps" and "movups" and have the same rules

for operands.

  "movlpd" moves double precision value between the memory and the low quad

word of SSE register. "movhpd" moved double precision value between the memory

and the high quad word of SSE register. These instructions are analogous to

"movlps" and "movhps" and have the same rules for operands.

  "movmskpd" transfers the most significant bit of each of the two double

precision values in the SSE register into low two bits of a general register.

This instruction is analogous to "movmskps" and has the same rules for

operands.

  "movsd" transfers a double precision value between source and destination

operand (only the low quad word is trasferred). At least one of the operands

have to be a SSE register, the second one can be also a SSE register or 64-bit

memory location.

  Arithmetic operations on double precision values are: "addpd", "addsd",

"subpd", "subsd", "mulpd", "mulsd", "divpd", "divsd", "sqrtpd", "sqrtsd",

"maxpd", "maxsd", "minpd", "minsd", and they are analoguous to arithmetic

operations on single precision values described in previous section. When the

mnemonic ends with "pd" instead of "ps", the operation is performed on packed

two double precision values, but rules for operands are the same. When the

mnemonic ends with "sd" instead of "ss", the source operand can be a 64-bit

memory location or a SSE register, the destination operand must be a SSE

register and the operation is performed on double precision values, only low

quad words of SSE registers are used in this case.

  "andpd", "andnpd", "orpd" and "xorpd" perform the logical operations on

packed double precision values. They are analoguous to SSE logical operations

on single prevision values and have the same rules for operands.

  "cmppd" compares packed double precision values and returns and returns a

mask result into the destination operand. This instruction is analoguous to

"cmpps" and has the same rules for operands. "cmpsd" performs the same

operation on double precision values, only low quad word of destination

register is affected, in this case source operand can be a 64-bit memory or

SSE register. Variant with only two operands are obtained by attaching the

condition mnemonic from table 2.3 to the "cmp" mnemonic and then attaching

the "pd" or "sd" at the end.

  "comisd" and "ucomisd" compare the double precision values and set the ZF,

PF and CF flags to show the result. The destination operand must be a SSE

register, the source operand can be a 128-bit memory location or SSE register.

  "shufpd" moves any of the two double precision values from the destination

operand into the low quad word of the destination operand, and any of the two

values from the source operand into the high quad word of the destination

operand. This instruction is analoguous to "shufps" and has the same rules for

operand. Bit 0 of the third operand selects the value to be moved from the

destination operand, bit 1 selects the value to be moved from the source

operand, the rest of bits are reserved and must be zeroed.

  "unpckhpd" performs an unpack of the high quad words from the source and

destination operands, "unpcklpd" performs an unpack of the low quad words from

the source and destination operands. They are analoguous to "unpckhps" and

"unpcklps", and have the same rules for operands.

  "cvtps2pd" converts the packed two single precision floating point values to

two packed double precision floating point values, the destination operand

must be a SSE register, the source operand can be a 64-bit memory location or

SSE register. "cvtpd2ps" converts the packed two double precision floating

point values to packed two single precision floating point values, the

destination operand must be a SSE register, the source operand can be a

128-bit memory location or SSE register. "cvtss2sd" converts the single

precision floating point value to double precision floating point value, the

destination operand must be a SSE register, the source operand can be a 32-bit

memory location or SSE register. "cvtsd2ss" converts the double precision

floating point value to single precision floating point value, the destination

operand must be a SSE register, the source operand can be 64-bit memory

location or SSE register.

  "cvtpi2pd" converts packed two double word integers into the the packed

double precision floating point values, the destination operand must be a SSE

register, the source operand can be a 64-bit memory location or MMX register.

"cvtsi2sd" converts a double word integer into a double precision floating

point value, the destination operand must be a SSE register, the source

operand can be a 32-bit memory location or 32-bit general register. "cvtpd2pi"

converts packed double precision floating point values into packed two double

word integers, the destination operand should be a MMX register, the source

operand can be a 128-bit memory location or SSE register. "cvttpd2pi" performs

the similar operation, except that truncation is used to round a source values

to integers, rules for operands are the same. "cvtsd2si" converts a double

precision floating point value into a double word integer, the destination

operand should be a 32-bit general register, the source operand can be a

64-bit memory location or SSE register. "cvttsd2si" performs the similar

operation, except that truncation is used to round a source value to integer,

rules for operands are the same.

  "cvtps2dq" and "cvttps2dq" convert packed single precision floating point

values to packed four double word integers, storing them in the destination

operand. "cvtpd2dq" and "cvttpd2dq" convert packed double precision floating

point values to packed two double word integers, storing the result in the low

quad word of the destination operand. "cvtdq2ps" converts packed four

double word integers to packed single precision floating point values.

For all these instructions destination operand must be a SSE register, the

source operand can be a 128-bit memory location or SSE register.

"cvtdq2pd" converts packed two double word integers from the source operand to

packed double precision floating point values, the source can be a 64-bit

memory location or SSE register, destination has to be SSE register.

  "movdqa" and "movdqu" transfer a double quad word operand containing packed

integers from source operand to destination operand. At least one of the

operands have to be a SSE register, the second one can be also a SSE register

or 128-bit memory location. Memory operands for "movdqa" instruction must be

aligned on boundary of 16 bytes, operands for "movdqu" instruction don't have

to be aligned.

  "movq2dq" moves the contents of the MMX source register to the low quad word

of destination SSE register. "movdq2q" moves the low quad word from the source

SSE register to the destination MMX register.

 

    movq2dq xmm0,mm1   ; move from MMX register to SSE register

    movdq2q mm0,xmm1   ; move from SSE register to MMX register

 

  All MMX instructions operating on the 64-bit packed integers (those with

mnemonics starting with "p") are extended to operate on 128-bit packed

integers located in SSE registers. Additional syntax for these instructions

needs an SSE register where MMX register was needed, and the 128-bit memory

location or SSE register where 64-bit memory location or MMX register were

needed. The exception is "pshufw" instruction, which doesn't allow extended

syntax, but has two new variants: "pshufhw" and "pshuflw", which allow only

the extended syntax, and perform the same operation as "pshufw" on the high

or low quad words of operands respectively. Also the new instruction "pshufd"

is introduced, which performs the same operation as "pshufw", but on the

double words instead of words, it allows only the extended syntax.

 

    psubb xmm0,[esi]   ; subtract 16 packed bytes

    pextrw eax,xmm0,7  ; extract highest word into eax

 

  "paddq" performs the addition of packed quad words, "psubq" performs the

subtraction of packed quad words, "pmuludq" performs an unsigned

multiplication of low double words from each corresponding quad words and

returns the results in packed quad words. These instructions follow the same

rules for operands as the general MMX operations described in 2.1.14.

  "pslldq" and "psrldq" perform logical shift left or right of the double

quad word in the destination operand by the amount of bytes specified in the

source operand. The destination operand should be a SSE register, source

operand should be an 8-bit immediate value.

  "punpckhqdq" interleaves the high quad word of the source operand and the

high quad word of the destination operand and writes them to the destination

SSE register. "punpcklqdq" interleaves the low quad word of the source operand

and the low quad word of the destination operand and writes them to the

destination SSE register. The source operand can be a 128-bit memory location

or SSE register.

  "movntdq" stores packed integer data from the SSE register to memory using

non-temporal hint. The source operand should be a SSE register, the

destination operand should be a 128-bit memory location. "movntpd" stores

packed double precision values from the SSE register to memory using a

non-temporal hint. Rules for operand are the same. "movnti" stores integer

from a general register to memory using a non-temporal hint. The source

operand should be a 32-bit general register, the destination operand should

be a 32-bit memory location. "maskmovdqu" stores selected bytes from the first

operand into a 128-bit memory location using a non-temporal hint. Both

operands should be a SSE registers, the second operand selects wich bytes from

the source operand are written to memory. The memory location is pointed by DI

(or EDI) register in the segment selected by DS and does not need to be

aligned.

  "clflush" writes and invalidates the cache line associated with the address

of byte specified with the operand, which should be a 8-bit memory location.

  "lfence" performs a serializing operation on all instruction loading from

memory that were issued prior to it. "mfence" performs a serializing operation

on all instruction accesing memory that were issued prior to it, and so it

combines the functions of "sfence" (described in previous section) and

"lfence" instructions. These instructions have no operands.

 

 

2.1.17  SSE3 instructions

 

Prescott technology introduced some new instructions to improve the performance

of SSE and SSE2 - this extension is called SSE3.

  "fisttp" behaves like the "fistp" instruction and accepts the same operands,

the only difference is that it always used truncation, irrespective of the

rounding mode.

  "movshdup" loads into destination operand the 128-bit value obtained from

the source value of the same size by filling the each quad word with the two

duplicates of the value in its high double word. "movsldup" performs the same

action, except it duplicates the values of low double words. The destination

operand should be SSE register, the source operand can be SSE register or

128-bit memory location.

  "movddup" loads the 64-bit source value and duplicates it into high and low

quad word of the destination operand. The destination operand should be SSE

register, the source operand can be SSE register or 64-bit memory location.

  "lddqu" is functionally equivalent to "movdqu" with memory as source

operand, but it may improve performance when the source operand crosses a

cacheline boundary. The destination operand has to be SSE register, the source

operand must be 128-bit memory location.

  "addsubps" performs single precision addition of second and fourth pairs and

single precision subtracion of the first and third pairs of floating point

values in the operands. "addsubpd" performs double precision addition of the

second pair and double precision subtraction of the first pair of floating

point values in the operand. "haddps" performs the addition of two single

precision values within the each quad word of source and destination operands,

and stores the results of such horizontal addition of values from destination

operand into low quad word of destination operand, and the results from the

source operand into high quad word of destination operand. "haddpd" performs

the addition of two double precision values within each operand, and stores

the result from destination operand into low quad word of destination operand,

and the result from source operand into high quad word of destination operand.

All these instructions need the destination operand to be SSE register, source

operand can be SSE register or 128-bit memory location.

  "monitor" sets up an address range for monitoring of write-back stores. It

need its three operands to be EAX, ECX and EDX register in that order. "mwait"

waits for a write-back store to the address range set up by the "monitor"

instruction. It uses two operands with additional parameters, first being the

EAX and second the ECX register.

  The functionality of SSE3 is further extended by the set of Supplemental

SSE3 instructions (SSSE3). They generally follow the same rules for operands

as all the MMX operations extended by SSE.

  "phaddw" and "phaddd" perform the horizontal additional of the pairs of

adjacent values from both the source and destination operand, and stores the

sums into the destination (sums from the source operand go into higher part of

destination register). They operate on 16-bit or 32-bit chunks, respectively.

"phaddsw" performs the same operation on signed 16-bit packed values, but the

result of each addition is saturated. "phsubw" and "phsubd" analogously

perform the horizontal subtraction of 16-bit or 32-bit packed value, and

"phsubsw" performs the horizontal subtraction of signed 16-bit packed values

with saturation.

  "pabsb", "pabsw" and "pabsd" calculate the absolute value of each signed

packed signed value in source operand and stores them into the destination

register. They operator on 8-bit, 16-bit and 32-bit elements respectively.

  "pmaddubsw" multiplies signed 8-bit values from the source operand with the

corresponding unsigned 8-bit values from the destination operand to produce

intermediate 16-bit values, and every adjacent pair of those intermediate

values is then added horizontally and those 16-bit sums are stored into the

destination operand.

  "pmulhrsw" multiplies corresponding 16-bit integers from the source and

destination operand to produce intermediate 32-bit values, and the 16 bits

next to the highest bit of each of those values are then rounded and packed

into the destination operand.

  "pshufb" shuffles the bytes in the destination operand according to the

mask provided by source operand - each of the bytes in source operand is

an index of the target position for the corresponding byte in the destination.

  "psignb", "psignw" and "psignd" perform the operation on 8-bit, 16-bit or

32-bit integers in destination operand, depending on the signs of the values

in the source. If the value in source is negative, the corresponding value in

the destination register is negated, if the value in source is positive, no

operation is performed on the corresponding value is performed, and if the

value in source is zero, the value in destination is zeroed, too.

  "palignr" appends the source operand to the destination operand to form the

intermediate value of twice the size, and then extracts into the destination

register the 64 or 128 bits that are right-aligned to the byte offset

specified by the third operand, which should be an 8-bit immediate value. This

is the only SSSE3 instruction that takes three arguments.

 

 

2.1.18  AMD 3DNow! instructions

 

The 3DNow! extension adds a new MMX instructions to those described in 2.1.14,

and introduces operation on the 64-bit packed floating point values, each

consisting of two single precision floating point values.

  These instructions follow the same rules as the general MMX operations, the

destination operand should be a MMX register, the source operand can be a MMX

register or 64-bit memory location. "pavgusb" computes the rounded averages

of packed unsigned bytes. "pmulhrw" performs a signed multiplication of the

packed words, round the high word of each double word results and stores them

in the destination operand. "pi2fd" converts packed double word integers into

packed floating point values. "pf2id" converts packed floating point values

into packed double word integers using truncation. "pi2fw" converts packed

word integers into packed floating point values, only low words of each

double word in source operand are used. "pf2iw" converts packed floating

point values to packed word integers, results are extended to double words

using the sign extension. "pfadd" adds packed floating point values. "pfsub"

and "pfsubr" subtracts packed floating point values, the first one subtracts

source values from destination values, the second one subtracts destination

values from the source values. "pfmul" multiplies packed floating point

values. "pfacc" adds the low and high floating point values of the destination

operand, storing the result in the low double word of destination, and adds

the low and high floating point values of the source operand, storing the

result in the high double word of destination. "pfnacc" subtracts the high

floating point value of the destination operand from the low, storing the

result in the low double word of destination, and subtracts the high floating

point value of the source operand from the low, storing the result in the high

double word of destination. "pfpnacc" subtracts the high floating point value

of the destination operand from the low, storing the result in the low double

word of destination, and adds the low and high floating point values of the

source operand, storing the result in the high double word of destination.

"pfmax" and "pfmin" compute the maximum and minimum of floating point values.

"pswapd" reverses the high and low double word of the source operand. "pfrcp"

returns an estimates of the reciprocals of floating point values from the

source operand, "pfrsqrt" returns an estimates of the reciprocal square

roots of floating point values from the source operand, "pfrcpit1" performs

the first step in the Newton-Raphson iteration to refine the reciprocal

approximation produced by "pfrcp" instruction, "pfrsqit1" performs the first

step in the Newton-Raphson iteration to refine the reciprocal square root

approximation produced by "pfrsqrt" instruction, "pfrcpit2" performs the

second final step in the Newton-Raphson iteration to refine the reciprocal

approximation or the reciprocal square root approximation. "pfcmpeq",

"pfcmpge" and "pfcmpgt" compare the packed floating point values and sets

all bits or zeroes all bits of the correspoding data element in the

destination operand according to the result of comparison, first checks

whether values are equal, second checks whether destination value is greater

or equal to source value, third checks whether destination value is greater

than source value.

  "prefetch" and "prefetchw" load the line of data from memory that contains

byte specified with the operand into the data cache, "prefetchw" instruction

should be used when the data in the cache line is expected to be modified,

otherwise the "prefetch" instruction should be used. The operand should be an

8-bit memory location.

  "femms" performs a fast clear of MMX state. This instruction has no

operands.

 

 

2.1.19  The x86-64 long mode instructions

 

The AMD64 and EM64T architectures (we will use the common name x86-64 for them

both) extend the x86 instruction set for the 64-bit processing. While legacy

and compatibility modes use the same set of registers and instructions, the

new long mode extends the x86 operations to 64 bits and introduces several new

registers. You can turn on generating the code for this mode with the "use64"

directive.

  Each of the general purpose registers is extended to 64 bits and the eight

whole new general purpose registers and also eight new SSE registers are added.

See table 2.4 for the summary of new registers (only the ones that was not

listed in table 1.2). The general purpose registers of smallers sizes are the

low order portions of the larger ones. You can still access the "ah", "bh",

"ch" and "dh" registers in long mode, but you cannot use them in the same

instruction with any of the new registers.

 

   Table 2.4  New registers in long mode

  ÚÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄ¿

  ³ Type ³          General          ³  SSE  ³  AVX  ³

  ÃÄÄÄÄÄÄÅÄÄÄÄÄÄÂÄÄÄÄÄÄÂÄÄÄÄÄÄÂÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄ´

  ³ Bits ³  8   ³  16  ³  32  ³  64  ³  128  ³  256  ³

  ÆÍÍÍÍÍÍØÍÍÍÍÍÍØÍÍÍÍÍÍØÍÍÍÍÍÍØÍÍÍÍÍÍØÍÍÍÍÍÍÍØÍÍÍÍÍÍ͵

  ³      ³      ³      ³      ³ rax  ³       ³       ³

  ³      ³      ³      ³      ³ rcx  ³       ³       ³

  ³      ³      ³      ³      ³ rdx  ³       ³       ³

  ³      ³      ³      ³      ³ rbx  ³       ³       ³

  ³      ³ spl  ³      ³      ³ rsp  ³       ³       ³

  ³      ³ bpl  ³      ³      ³ rbp  ³       ³       ³

  ³      ³ sil  ³      ³      ³ rsi  ³       ³       ³

  ³      ³ dil  ³      ³      ³ rdi  ³       ³       ³

  ³      ³ r8b  ³ r8w  ³ r8d  ³ r8   ³ xmm8  ³ ymm8  ³

  ³      ³ r9b  ³ r9w  ³ r9d  ³ r9   ³ xmm9  ³ ymm9  ³

  ³      ³ r10b ³ r10w ³ r10d ³ r10  ³ xmm10 ³ ymm10 ³

  ³      ³ r11b ³ r11w ³ r11d ³ r11  ³ xmm11 ³ ymm11 ³

  ³      ³ r12b ³ r12w ³ r12d ³ r12  ³ xmm12 ³ ymm12 ³

  ³      ³ r13b ³ r13w ³ r13d ³ r13  ³ xmm13 ³ ymm13 ³

  ³      ³ r14b ³ r14w ³ r14d ³ r14  ³ xmm14 ³ ymm14 ³

  ³      ³ r15b ³ r15w ³ r15d ³ r15  ³ xmm15 ³ ymm15 ³

  ÀÄÄÄÄÄÄÁÄÄÄÄÄÄÁÄÄÄÄÄÄÁÄÄÄÄÄÄÁÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÙ

 

   In general any instruction from x86 architecture, which allowed 16-bit or

32-bit operand sizes, in long mode allows also the 64-bit operands. The 64-bit

registers should be used for addressing in long mode, the 32-bit addressing

is also allowed, but it's not possible to use the addresses based on 16-bit

registers. Below are the samples of new operations possible in long mode on the

example of "mov" instruction:

 

    mov rax,r8   ; transfer 64-bit general register

    mov al,[rbx] ; transfer memory addressed by 64-bit register

 

The long mode uses also the instruction pointer based addresses, you can

specify it manually with the special RIP register symbol, but such addressing

is also automatically generated by flat assembler, since there is no 64-bit

absolute addressing in long mode. You can still force the assembler to use the

32-bit absolute addressing by putting the "dword" size override for address

inside the square brackets. There is also one exception, where the 64-bit

absolute addressing is possible, it's the "mov" instruction with one of the

operand being accumulator register, and second being the memory operand.

To force the assembler to use the 64-bit absolute addressing there, use the

"qword" size operator for address inside the square brackets. When no size

operator is applied to address, assembler generates the optimal form

automatically.

 

    mov [qword 0],rax  ; absolute 64-bit addressing

    mov [dword 0],r15d ; absolute 32-bit addressing

    mov [0],rsi        ; automatic RIP-relative addressing

    mov [rip+3],sil    ; manual RIP-relative addressing

 

  Also as the immediate operands for 64-bit operations only the signed 32-bit

values are possible, with the only exception being the "mov" instruction with

destination operand being 64-bit general purpose register. Trying to force the

64-bit immediate with any other instruction will cause an error.

  If any operation is performed on the 32-bit general registers in long mode,

the upper 32 bits of the 64-bit registers containing them are filled with

zeros. This is unlike the operations on 16-bit or 8-bit portions of those

registers, which preserve the upper bits.

  Three new type conversion instructions are available. The "cdqe" sign

extends the double word in EAX into quad word and stores the result in RAX

register. "cqo" sign extends the quad word in RAX into double quad word and

stores the extra bits in the RDX register. These instructions have no

operands. "movsxd" sign extends the double word source operand, being either

the 32-bit register or memory, into 64-bit destination operand, which has to

be register. No analogous instruction is needed for the zero extension, since

it is done automatically by any operations on 32-bit registers, as noted in

previous paragraph. And the "movzx" and "movsx" instructions, conforming to

the general rule, can be used with 64-bit destination operand, allowing

extension of byte or word values into quad words.

  All the binary arithmetic and logical instruction have been promoted to

allow 64-bit operands in long mode. The use of decimal arithmetic instructions

in long mode is prohibited.

  The stack operations, like "push" and "pop" in long mode default to 64-bit

operands and it's not possible to use 32-bit operands with them. The "pusha"

and "popa" are disallowed in long mode.

  The indirect near jumps and calls in long mode default to 64-bit operands

and it's not possible to use the 32-bit operands with them. On the other hand,

the indirect far jumps and calls allow any operands that were allowed by the

x86 architecture and also 80-bit memory operand is allowed (though only EM64T

seems to implement such variant), with the first eight bytes defining the

offset and two last bytes specifying the selector. The direct far jumps and

calls are not allowed in long mode.

  The I/O instructions, "in", "out", "ins" and "outs" are the exceptional

instructions that are not extended to accept quad word operands in long mode.

But all other string operations are, and there are new short forms "movsq",

"cmpsq", "scasq", "lodsq" and "stosq" introduced for the variants of string

operations for 64-bit string elements. The RSI and RDI registers are used by

default to address the string elements.

  The "lfs", "lgs" and "lss" instructions are extended to accept 80-bit source

memory operand with 64-bit destination register (though only EM64T seems to

implement such variant). The "lds" and "les" are disallowed in long mode.

  The system instructions like "lgdt" which required the 48-bit memory operand,

in long mode require the 80-bit memory operand.

  The "cmpxchg16b" is the 64-bit equivalent of "cmpxchg8b" instruction, it uses

the double quad word memory operand and 64-bit registers to perform the

analoguous operation.

  The "fxsave64" and "fxrstor64" are new variants of "fxsave" and "fxrstor"

instructions, available only in long mode, which use a different format of

storage area in order to store some pointers in full 64-bit size.  

  "swapgs" is the new instruction, which swaps the contents of GS register and

the KernelGSbase model-specific register (MSR address 0C0000102h).

  "syscall" and "sysret" is the pair of new instructions that provide the

functionality similar to "sysenter" and "sysexit" in long mode, where the

latter pair is disallowed. The "sysexitq" and "sysretq" mnemonics provide the

64-bit versions of "sysexit" and "sysret" instructions.

  The "rdmsrq" and "wrmsrq" mnemonics are the 64-bit variants of the "rdmsr"

and "wrmsr" instructions.

 

 

2.1.20  SSE4 instructions

 

There are actually three different sets of instructions under the name SSE4.

Intel designed two of them, SSE4.1 and SSE4.2, with latter extending the

former into the full Intel's SSE4 set. On the other hand, the implementation

by AMD includes only a few instructions from this set, but also contains

some additional instructions, that are called the SSE4a set.

  The SSE4.1 instructions mostly follow the same rules for operands, as

the basic SSE operations, so they require destination operand to be SSE

register and source operand to be 128-bit memory location or SSE register,

and some operations require a third operand, the 8-bit immediate value.

  "pmulld" performs a signed multiplication of the packed double words and

stores the low double words of the results in the destination operand.

"pmuldq" performs a two signed multiplications of the corresponding double

words in the lower quad words of operands, and stores the results as

packed quad words into the destination register. "pminsb" and "pmaxsb"

return the minimum or maximum values of packed signed bytes, "pminuw" and

"pmaxuw" return the minimum and maximum values of packed unsigned words,

"pminud", "pmaxud", "pminsd" and "pmaxsd" return minimum or maximum values

of packed unsigned or signed words. These instructions complement the

instructions computing packed minimum or maximum introduced by SSE.

  "ptest" sets the ZF flag to one when the result of bitwise AND of the

both operands is zero, and zeroes the ZF otherwise. It also sets CF flag

to one, when the result of bitwise AND of the destination operand with

the bitwise NOT of the source operand is zero, and zeroes the CF otherwise.

"pcmpeqq" compares packed quad words for equality, and fills the

corresponding elements of destination operand with either ones or zeros,

depending on the result of comparison.

  "packusdw" converts packed signed double words from both the source and

destination operand into the unsigned words using saturation, and stores

the eight resulting word values into the destination register.

  "phminposuw" finds the minimum unsigned word value in source operand and

places it into the lowest word of destination operand, setting the remaining

upper bits of destination to zero.

  "roundps", "roundss", "roundpd" and "roundsd" perform the rounding of packed

or individual floating point value of single or double precision, using the

rounding mode specified by the third operand.

 

    roundsd xmm0,xmm1,0011b ; round toward zero

 

  "dpps" calculates dot product of packed single precision floating point

values, that is it multiplies the corresponding pairs of values from source and

destination operand and then sums the products up. The high four bits of the

8-bit immediate third operand control which products are calculated and taken

to the sum, and the low four bits control, into which elements of destination

the resulting dot product is copied (the other elements are filled with zero).

"dppd" calculates dot product of packed double precision floating point values.

The bits 4 and 5 of third operand control, which products are calculated and

added, and bits 0 and 1 of this value control, which elements in destination

register should get filled with the result. "mpsadbw" calculates multiple sums

of absolute differences of unsigned bytes. The third operand controls, with

value in bits 0-1, which of the four-byte blocks in source operand is taken to

calculate the absolute differencies, and with value in bit 2, at which of the

two first four-byte block in destination operand start calculating multiple

sums. The sum is calculated from four absolute differencies between the

corresponding unsigned bytes in the source and destination block, and each next

sum is calculated in the same way, but taking the four bytes from destination

at the position one byte after the position of previous block. The four bytes

from the source stay the same each time. This way eight sums of absolute

differencies are calculated and stored as packed word values into the

destination operand. The instructions described in this paragraph follow the

same rules for operands, as "roundps" instruction.

  "blendps", "blendvps", "blendpd" and "blendvpd" conditionally copy the

values from source operand into the destination operand, depending on the bits

of the mask provided by third operand. If a mask bit is set, the corresponding

element of source is copied into the same place in destination, otherwise this

position is destination is left unchanged. The rules for the first two operands

are the same, as for general SSE instructions. "blendps" and "blendpd" need

third operand to be 8-bit immediate, and they operate on single or double

precision values, respectively. "blendvps" and "blendvpd" require third operand

to be the XMM0 register.

 

    blendvps xmm3,xmm7,xmm0 ; blend according to mask

 

  "pblendw" conditionally copies word elements from the source operand into the

destination, depending on the bits of mask provided by third operand, which

needs to be 8-bit immediate value. "pblendvb" conditionally copies byte

elements from the source operands into destination, depending on mask defined

by the third operand, which has to be XMM0 register. These instructions follow

the same rules for operands as "blendps" and "blendvps" instructions,

respectively.

  "insertps" inserts a single precision floating point value taken from the

position in source operand specified by bits 6-7 of third operand into location

in destination register selected by bits 4-5 of third operand. Additionally,

the low four bits of third operand control, which elements in destination

register will be set to zero. The first two operands follow the same rules as

for the general SSE operation, the third operand should be 8-bit immediate.

  "extractps" extracts a single precision floating point value taken from the

location in source operand specified by low two bits of third operand, and

stores it into the destination operand. The destination can be a 32-bit memory

value or general purpose register, the source operand must be SSE register,

and the third operand should be 8-bit immediate value.

 

    extractps edx,xmm3,3 ; extract the highest value

 

  "pinsrb", "pinsrd" and "pinsrq" copy a byte, double word or quad word from

the source operand into the location of destination operand determined by the

third operand. The destination operand has to be SSE register, the source

operand can be a memory location of appropriate size, or the 32-bit general

purpose register (but 64-bit general purpose register for "pinsrq", which is

only available in long mode), and the third operand has to be 8-bit immediate

value. These instructions complement the "pinsrw" instruction operating on SSE

register destination, which was introduced by SSE2.

 

    pinsrd xmm4,eax,1 ; insert double word into second position

 

  "pextrb", "pextrw", "pextrd" and "pextrq" copy a byte, word, double word or

quad word from the location in source operand specified by third operand, into

the destination. The source operand should be SSE register, the third operand

should be 8-bit immediate, and the destination operand can be memory location

of appropriate size, or the 32-bit general purpose register (but 64-bit general

purpose register for "pextrq", which is only available in long mode). The

"pextrw" instruction with SSE register as source was already introduced by

SSE2, but SSE4 extends it to allow memory operand as destination.

 

    pextrw [ebx],xmm3,7 ; extract highest word into memory

 

  "pmovsxbw" and "pmovzxbw" perform sign extension or zero extension of eight

byte values from the source operand into packed word values in destination

operand, which has to be SSE register. The source can be 64-bit memory or SSE

register - when it is register, only its low portion is used. "pmovsxbd" and

"pmovzxbd" perform sign extension or zero extension of the four byte values

from the source operand into packed double word values in destination operand,

the source can be 32-bit memory or SSE register. "pmovsxbq" and "pmovzxbq"

perform sign extension or zero extension of the two byte values from the

source operand into packed quad word values in destination operand, the source

can be 16-bit memory or SSE register. "pmovsxwd" and "pmovzxwd" perform sign

extension or zero extension of the four word values from the source operand

into packed double words in destination operand, the source can be 64-bit

memory or SSE register. "pmovsxwq" and "pmovzxwq" perform sign extension or

zero extension of the two word values from the source operand into packed quad

words in destination operand, the source can be 32-bit memory or SSE register.

"pmovsxdq" and "pmovzxdq" perform sign extension or zero extension of the two

double word values from the source operand into packed quad words in

destination operand, the source can be 64-bit memory or SSE register.

 

    pmovzxbq xmm0,word [si]  ; zero-extend bytes to quad words

    pmovsxwq xmm0,xmm1       ; sign-extend words to quad words

 

  "movntdqa" loads double quad word from the source operand to the destination

using a non-temporal hint. The destination operand should be SSE register,

and the source operand should be 128-bit memory location.

  The SSE4.2, described below, adds not only some new operations on SSE

registers, but also introduces some completely new instructions operating on

general purpose registers only.

  "pcmpistri" compares two zero-ended (implicit length) strings provided in

its source and destination operand and generates an index stored to ECX;

"pcmpistrm" performs the same comparison and generates a mask stored to XMM0.

"pcmpestri" compares two strings of explicit lengths, with length provided

in EAX for the destination operand and in EDX for the source operand, and

generates an index stored to ECX; "pcmpestrm" performs the same comparision

and generates a mask stored to XMM0. The source and destination operand follow

the same rules as for general SSE instructions, the third operand should be

8-bit immediate value determining the details of performed operation - refer to

Intel documentation for information on those details.

  "pcmpgtq" compares packed quad words, and fills the corresponding elements of

destination operand with either ones or zeros, depending on whether the value

in destination is greater than the one in source, or not. This instruction

follows the same rules for operands as "pcmpeqq".

  "crc32" accumulates a CRC32 value for the source operand starting with

initial value provided by destination operand, and stores the result in

destination. Unless in long mode, the destination operand should be a 32-bit

general purpose register, and the source operand can be a byte, word, or double

word register or memory location. In long mode the destination operand can

also be a 64-bit general purpose register, and the source operand in such case

can be a byte or quad word register or memory location.

 

    crc32 eax,dl          ; accumulate CRC32 on byte value

    crc32 eax,word [ebx]  ; accumulate CRC32 on word value

    crc32 rax,qword [rbx] ; accumulate CRC32 on quad word value

 

  "popcnt" calculates the number of bits set in the source operand, which can

be 16-bit, 32-bit, or 64-bit general purpose register or memory location,

and stores this count in the destination operand, which has to be register of

the same size as source operand. The 64-bit variant is available only in long

mode.

 

    popcnt ecx,eax        ; count bits set to 1

 

  The SSE4a extension, which also includes the "popcnt" instruction introduced

by SSE4.2, at the same time adds the "lzcnt" instruction, which follows the

same syntax, and calculates the count of leading zero bits in source operand

(if the source operand is all zero bits, the total number of bits in source

operand is stored in destination).

  "extrq" extract the sequence of bits from the low quad word of SSE register

provided as first operand and stores them at the low end of this register,

filling the remaining bits in the low quad word with zeros. The position of bit

string and its length can either be provided with two 8-bit immediate values

as second and third operand, or by SSE register as second operand (and there

is no third operand in such case), which should contain position value in bits

8-13 and length of bit string in bits 0-5.

 

    extrq xmm0,8,7        ; extract 8 bits from position 7

    extrq xmm0,xmm5       ; extract bits defined by register

 

  "insertq" writes the sequence of bits from the low quad word of the source

operand into specified position in low quad word of the destination operand,

leaving the other bits in low quad word of destination intact. The position

where bits should be written and the length of bit string can either be

provided with two 8-bit immediate values as third and fourth operand, or by

the bit fields in source operand (and there are only two operands in such

case), which should contain position value in bits 72-77 and length of bit

string in bits 64-69.

 

    insertq xmm1,xmm0,4,2 ; insert 4 bits at position 2

    insertq xmm1,xmm0     ; insert bits defined by register

 

  "movntss" and "movntsd" store single or double precision floating point

value from the source SSE register into 32-bit or 64-bit destination memory

location respectively, using non-temporal hint.

 

 

2.1.21  AVX instructions

 

The Advanced Vector Extensions introduce instructions that are new variants

of SSE instructions, with new scheme of encoding that allows extended syntax

having a destination operand separate from all the source operands. It also

introduces 256-bit AVX registers, which extend up the old 128-bit SSE

registers. Any AVX instruction that puts some result into SSE register, puts

zero bits into high portion of the AVX register containing it.

  The AVX version of SSE instruction has the mnemonic obtained by prepending

SSE instruction name with "v". For any SSE arithmetic instruction which had a

destination operand also being used as one of the source values, the AVX

variant has a new syntax with three operands - the destination and two sources.

The destination and first source can be SSE registers, and second source can be

SSE register or memory. If the operation is performed on single pair of values,

the remaining bits of first source SSE register are copied into the the

destination register.

 

    vsubss xmm0,xmm2,xmm3         ; subtract two 32-bit floats

    vmulsd xmm0,xmm7,qword [esi]  ; multiply two 64-bit floats

 

In case of packed operations, each instruction can also operate on the 256-bit

data size when the AVX registers are specified instead of SSE registers, and

the size of memory operand is also doubled then.

 

    vaddps ymm1,ymm5,yword [esi]  ; eight sums of 32-bit float pairs

 

The instructions that operate on packed integer types (in particular the ones

that earlier had been promoted from MMX to SSE) also acquired the new syntax

with three operands, however they are only allowed to operate on 128-bit

packed types and thus cannot use the whole AVX registers.

 

    vpavgw xmm3,xmm0,xmm2         ; average of 16-bit integers

    vpslld xmm1,xmm0,1            ; shift double words left

     

If the SSE version of instruction had a syntax with three operands, the third

one being an immediate value, the AVX version of such instruction takes four

operands, with immediate remaining the last one.

 

    vshufpd ymm0,ymm1,ymm2,10010011b ; shuffle 64-bit floats

    vpalignr xmm0,xmm4,xmm2,3        ; extract byte aligned value

     

The promotion to new syntax according to the rules described above has been

applied to all the instructions from SSE extensions up to SSE4, with the

exceptions described below.  

  "vdppd" instruction has syntax extended to four operans, but it does not

have a 256-bit version.

  The are a few instructions, namely "vsqrtpd", "vsqrtps", "vrcpps" and

"vrsqrtps", which can operate on 256-bit data size, but retained the syntax

with only two operands, because they use data from only one source:

   

    vsqrtpd ymm1,ymm0         ; put square roots into other register

 

In a similar way "vroundpd" and "vroundps" retained the syntax with three

operands, the last one being immediate value.  

 

    vroundps ymm0,ymm1,0011b  ; round toward zero

                             

  Also some of the operations on packed integers kept their two-operand or

three-operand syntax while being promoted to AVX version. In such case these

instructions follow exactly the same rules for operands as their SSE

counterparts (since operations on packed integers do not have 256-bit variants

in AVX extension). These include "vpcmpestri", "vpcmpestrm", "vpcmpistri",

"vpcmpistrm", "vphminposuw", "vpshufd", "vpshufhw", "vpshuflw". And there are

more instructions that in AVX versions keep exactly the same syntax for

operands as the one from SSE, without any additional options: "vcomiss",

"vcomisd", "vcvtss2si", "vcvtsd2si", "vcvttss2si", "vcvttsd2si", "vextractps",

"vpextrb", "vpextrw", "vpextrd", "vpextrq", "vmovd", "vmovq", "vmovntdqa",

"vmaskmovdqu", "vpmovmskb", "vpmovsxbw", "vpmovsxbd", "vpmovsxbq", "vpmovsxwd",

"vpmovsxwq", "vpmovsxdq", "vpmovzxbw", "vpmovzxbd", "vpmovzxbq", "vpmovzxwd",

"vpmovzxwq" and "vpmovzxdq".

  The move and conversion instructions have mostly been promoted to allow

256-bit size operands in addition to the 128-bit variant with syntax identical

to that from SSE version of the same instruction. Each of the "vcvtdq2ps",

"vcvtps2dq" and "vcvttps2dq", "vmovaps", "vmovapd", "vmovups", "vmovupd",

"vmovdqa", "vmovdqu", "vlddqu", "vmovntps", "vmovntpd", "vmovntdq",

"vmovsldup", "vmovshdup", "vmovmskps" and "vmovmskpd" inherits the 128-bit

syntax from SSE without any changes, and also allows a new form with 256-bit

operands in place of 128-bit ones.  

 

    vmovups [edi],ymm6        ; store unaligned 256-bit data

   

  "vmovddup" has the identical 128-bit syntax as its SSE version, and it also

has a 256-bit version, which stores the duplicates of the lowest quad word

from the source operand in the lower half of destination operand, and in the

upper half of destination the duplicates of the low quad word from the upper

half of source. Both source and destination operands need then to be 256-bit

values.

  "vmovlhps" and "vmovhlps" have only 128-bit versions, and each takes three

operands, which all must be SSE registers. "vmovlhps" copies two single

precision values from the low quad word of second source register to the high

quad word of destination register, and copies the low quad word of first

source register into the low quad word of destination register. "vmovhlps"

copies two single  precision values from the high quad word of second source

register to the low quad word of destination register, and copies the high

quad word of first source register into the high quad word of destination

register.

  "vmovlps", "vmovhps", "vmovlpd" and "vmovhpd" have only 128-bit versions and

their syntax varies depending on whether memory operand is a destination or

source. When memory is destination, the syntax is identical to the one of

equivalent SSE instruction, and when memory is source, the instruction requires

three operands, first two being SSE registers and the third one 64-bit memory.

The value put into destination is then the value copied from first source with

either low or high quad word replaced with value from second source (the

memory operand).

 

    vmovhps [esi],xmm7       ; store upper half to memory

    vmovlps xmm0,xmm7,[ebx]  ; low from memory, rest from register  

 

  "vmovss" and "vmovsd" have syntax identical to their SSE equivalents as long

as one of the operands is memory, while the versions that operate purely on

registers require three operands (each being SSE register). The value stored

in destination is then the value copied from first source with lowest data

element replaced with the lowest value from second source.

 

    vmovss xmm3,[edi]        ; low from memory, rest zeroed

    vmovss xmm0,xmm1,xmm2    ; one value from xmm2, three from xmm1

 

  "vcvtss2sd", "vcvtsd2ss", "vcvtsi2ss" and "vcvtsi2d" use the three-operand

syntax, where destination and first source are always SSE registers, and the

second source follows the same rules and the source in syntax of equivalent

SSE instruction. The value stored in destination is then the value copied from

first source with lowest data element replaced with the result of conversion.

 

    vcvtsi2sd xmm4,xmm4,ecx  ; 32-bit integer to 64-bit float

    vcvtsi2ss xmm0,xmm0,rax  ; 64-bit integer to 32-bit float

 

  "vcvtdq2pd" and "vcvtps2pd" allow the same syntax as their SSE equivalents,

plus the new variants with AVX register as destination and SSE register or

128-bit memory as source. Analogously "vcvtpd2dq", "vcvttpd2dq" and

"vcvtpd2ps", in addition to variant with syntax identical to SSE version,

allow a variant with SSE register as destination and AVX register or 256-bit

memory as source.          

  "vinsertps", "vpinsrb", "vpinsrw", "vpinsrd", "vpinsrq" and "vpblendw" use

a syntax with four operands, where destination and first source have to be SSE

registers, and the third and fourth operand follow the same rules as second

and third operand in the syntax of equivalent SSE instruction. Value stored in

destination is the the value copied from first source with some data elements

replaced with values extracted from the second source, analogously to the

operation of corresponding SSE instruction.  

 

    vpinsrd xmm0,xmm0,eax,3  ; insert double word

 

  "vblendvps", "vblendvpd" and "vpblendvb" use a new syntax with four register

operands: destination, two sources and a mask, where second source can also be

a memory operand. "vblendvps" and "vblendvpd" have 256-bit variant, where

operands are AVX registers or 256-bit memory, as well as 128-bit variant,

which has operands being SSE registers or 128-bit memory. "vpblendvb" has only

a 128-bit variant. Value stored in destination is the value copied from the

first source with some data elements replaced, according to mask, by values

from the second source.

 

    vblendvps ymm3,ymm1,ymm2,ymm7  ; blend according to mask    

   

  "vptest" allows the same syntax as its SSE version and also has a 256-bit

version, with both operands doubled in size. There are also two new

instructions, "vtestps" and "vtestpd", which perform analogous tests, but only

of the sign bits of corresponding single precision or double precision values,

and set the ZF and CF accordingly. They follow the same syntax rules as

"vptest".

 

    vptest ymm0,yword [ebx]  ; test 256-bit values

    vtestpd xmm0,xmm1        ; test sign bits of 64-bit floats

 

  "vbroadcastss", "vbroadcastsd" and "vbroadcastf128" are new instructions,

which broadcast the data element defined by source operand into all elements

of corresponing size in the destination register. "vbroadcastss" needs

source to be 32-bit memory and destination to be either SSE or AVX register.

"vbroadcastsd" requires 64-bit memory as source, and AVX register as

destination. "vbroadcastf128" requires 128-bit memory as source, and AVX

register as destination.

 

    vbroadcastss ymm0,dword [eax]  ; get eight copies of value          

 

  "vinsertf128" is the new instruction, which takes four operands. The

destination and first source have to be AVX registers, second source can be

SSE register or 128-bit memory location, and fourth operand should be an

immediate value. It stores in destination the value obtained by taking

contents of first source and replacing one of its 128-bit units with value of

the second source. The lowest bit of fourth operand specifies at which

position that replacement is done (either 0 or 1).

  "vextractf128" is the new instruction with three operands. The destination

needs to be SSE register or 128-bit memory location, the source must be AVX

register, and the third operand should be an immediate value. It extracts

into destination one of the 128-bit units from source. The lowest bit of third

operand specifies, which unit is extracted.  

  "vmaskmovps" and "vmaskmovpd" are the new instructions with three operands

that selectively store in destination the elements from second source

depending on the sign bits of corresponding elements from first source. These

instructions can operate on either 128-bit data (SSE registers) or 256-bit

data (AVX registers). Either destination or second source has to be a memory

location of appropriate size, the two other operands should be registers.  

 

    vmaskmovps [edi],xmm0,xmm5  ; conditionally store

    vmaskmovpd ymm5,ymm0,[esi]  ; conditionally load  

 

  "vpermilpd" and "vpermilps" are the new instructions with three operands

that permute the values from first source according to the control fields from

second source and put the result into destination operand. It allows to use

either three SSE registers or three AVX registers as its operands, the second

source can be a memory of size equal to the registers used. In alternative

form the second source can be immediate value and then the first source

can be a memory location of the size equal to destination register.

  "vperm2f128" is the new instruction with four operands, which selects

128-bit blocks of floating point data from first and second source according

to the bit fields from fourth operand, and stores them in destination.

Destination and first source need to be AVX registers, second source can be

AVX register or 256-bit memory area, and fourth operand should be an immediate

value.

 

    vperm2f128 ymm0,ymm6,ymm7,12h  ; permute 128-bit blocks

 

  "vzeroall" instruction sets all the AVX registers to zero. "vzeroupper" sets

the upper 128-bit portions of all AVX registers to zero, leaving the SSE

registers intact. These new instructions take no operands.

  "vldmxcsr" and "vstmxcsr" are the AVX versions of "ldmxcsr" and "stmxcsr"

instructions. The rules for their operands remain unchanged.  

 

 

2.1.22  AVX2 instructions

 

The AVX2 extension allows all the AVX instructions operating on packed integers

to use 256-bit data types, and introduces some new instructions as well.

  The AVX instructions that operate on packed integers and had only a 128-bit

variants, have been supplemented with 256-bit variants, and thus their syntax

rules became analogous to AVX instructions operating on packed floating point

types.

 

    vpsubb ymm0,ymm0,[esi]   ; subtract 32 packed bytes

    vpavgw ymm3,ymm0,ymm2    ; average of 16-bit integers

 

However there are some instructions that have not been equipped with the

256-bit variants. "vpcmpestri", "vpcmpestrm", "vpcmpistri", "vpcmpistrm",

"vpextrb", "vpextrw", "vpextrd", "vpextrq", "vpinsrb", "vpinsrw", "vpinsrd",

"vpinsrq" and "vphminposuw" are not affected by AVX2 and allow only the

128-bit operands.

  The packed shift instructions, which allowed the third operand specifying

amount to be SSE register or 128-bit memory location, use the same rules

for the third operand in their 256-bit variant.

 

    vpsllw ymm2,ymm2,xmm4        ; shift words left

    vpsrad ymm0,ymm3,xword [ebx] ; shift double words right

 

  There are also new packed shift instructions with standard three-operand AVX

syntax, which shift each element from first source by the amount specified in

corresponding element of second source, and store the results in destination.

"vpsllvd" shifts 32-bit elements left, "vpsllvq" shifts 64-bit elements left,

"vpsrlvd" shifts 32-bit elements right logically, "vpsrlvq" shifts 64-bit

elements right logically and "vpsravd" shifts 32-bit elements right

arithmetically.

  The sign-extend and zero-extend instructions, which in AVX versions allowed

source operand to be SSE register or a memory of specific size, in the new

256-bit variant need memory of that size doubled or SSE register as source and

AVX register as destination.

 

    vpmovzxbq ymm0,dword [esi]   ; bytes to quad words

   

  Also "vmovntdqa" has been upgraded with 256-bit variant, so it allows to

transfer 256-bit value from memory to AVX register, it needs memory address

to be aligned to 32 bytes.  

  "vpmaskmovd" and "vpmaskmovq" are the new instructions with syntax identical

to "vmaskmovps" or "vmaskmovpd", and they performs analogous operation on

packed 32-bit or 64-bit values.    

  "vinserti128", "vextracti128", "vbroadcasti128" and "vperm2i128" are the new

instructions with syntax identical to "vinsertf128", "vextractf128",

"vbroadcastf128" and "vperm2f128" respectively, and they perform analogous

operations on 128-bit blocks of integer data.

  "vbroadcastss" and "vbroadcastsd" instructions have been extended to allow

SSE register as a source operand (which in AVX could only be a memory).

  "vpbroadcastb", "vpbroadcastw", "vpbroadcastd" and "vpbroadcastq" are the

new instructions which broadcast the byte, word, double word or quad word from

the source operand into all elements of corresponing size in the destination

register. The destination operand can be either SSE or AVX register, and the

source operand can be SSE register or memory of size equal to the size of data

element.

 

    vpbroadcastb ymm0,byte [ebx]  ; get 32 identical bytes

                 

  "vpermd" and "vpermps" are new three-operand instructions, which use each

32-bit element from first source as an index of element in second source which

is copied into destination at position corresponding to element containing

index. The destination and first source have to be AVX registers, and the

second source can be AVX register or 256-bit memory.

  "vpermq" and "vpermpd" are new three-operand instructions, which use 2-bit

indexes from the immediate value specified as third operand to determine which

element from source store at given position in destination. The destination

has to be AVX register, source can be AVX register or 256-bit memory, and the

third operand must be 8-bit immediate value.    

  The family of new instructions performing "gather" operation have special

syntax, as in their memory operand they use addressing mode that is unique to

them. The base of address can be a 32-bit or 64-bit general purpose register

(the latter only in long mode), and the index (possibly multiplied by scale

value, as in standard addressing) is specified by SSE or AVX register. It is

possible to use only index without base and any numerical displacement can be

added to the address. Each of those instructions takes three operands. First

operand is the destination register, second operand is memory addressed with

a vector index, and third operand is register containing a mask. The most

significant bit of each element of mask determines whether a value will be

loaded from memory into corresponding element in destination. The address of

each element to load is determined by using the corresponding element from

index register in memory operand to calculate final address with given base

and displacement. When the index register contains less elements than the

destination and mask registers, the higher elements of destination are zeroed.

After the value is successfuly loaded, the corresponding element in mask

register is set to zero. The destination, index and mask should all be

distinct registers, it is not allowed to use the same register in two

different roles.

  "vgatherdps" loads single precision floating point values addressed by

32-bit indexes. The destination, index and mask should all be registers of the

same type, either SSE or AVX. The data addressed by memory operand is 32-bit

in size.

 

    vgatherdps xmm0,[eax+xmm1],xmm3    ; gather four floats

    vgatherdps ymm0,[ebx+ymm7*4],ymm3  ; gather eight floats

 

  "vgatherqps" loads single precision floating point values addressed by

64-bit indexes. The destination and mask should always be SSE registers, while

index register can be either SSE or AVX register. The data addressed by memory

operand is 32-bit in size.

 

    vgatherqps xmm0,[xmm2],xmm3        ; gather two floats    

    vgatherqps xmm0,[ymm2+64],xmm3     ; gather four floats  

 

  "vgatherdpd" loads double precision floating point values addressed by

32-bit indexes. The index register should always be SSE register, the

destination and mask should be two registers of the same type, either SSE or

AVX. The data addressed by memory operand is 64-bit in size.

 

    vgatherdpd xmm0,[ebp+xmm1],xmm3    ; gather two doubles

    vgatherdpd ymm0,[xmm3*8],ymm5      ; gather four doubles

 

  "vgatherqpd" loads double precision floating point values addressed by

64-bit indexes. The destination, index and mask should all be registers of the

same type, either SSE or AVX. The data addressed by memory operand is 64-bit

in size.      

  "vpgatherdd" and "vpgatherqd" load 32-bit values addressed by either 32-bit

or 64-bit indexes. They follow the same rules as "vgatherdps" and "vgatherqps"

respectively.  

  "vpgatherdq" and "vpgatherqq" load 64-bit values addressed by either 32-bit

or 64-bit indexes. They follow the same rules as "vgatherdpd" and "vgatherqpd"

respectively.  

 

 

2.1.23  Auxiliary sets of computational instructions

 

  There is a number of additional instruction set extensions related to

AVX. They introduce new vector instructions (and sometimes also their SSE

equivalents that use classic instruction encoding), and even some new

instructions operating on general registers that use the AVX-like encoding

allowing the extended syntax with separate destination and source operands.

The CPU support for each of these instructions sets needs to be determined

separately.    

  The AES extension provides a specialized set of instructions for the

purpose of cryptographic computations defined by Advanced Encryption Standard.

Each of these instructions has two versions: the AVX one and the one with

SSE-like syntax that uses classic encoding. Refer to the Intel manuals for the

details of operation of these instructions.

  "aesenc" and "aesenclast" perform a single round of AES encryption on data

from first source with a round key from second source, and store result in

destination. The destination and first source are SSE registers, and the

second source can be SSE register or 128-bit memory. The AVX versions of these

instructions, "vaesenc" and "vaesenclast", use the syntax with three operands,

while the SSE-like version has only two operands, with first operand being

both the destination and first source.

  "aesdec" and "aesdeclast" perform a single round of AES decryption on data

from first source with a round key from second source. The syntax rules for

them and their AVX versions are the same as for "aesenc".

  "aesimc" performs the InvMixColumns transformation of source operand and

store the result in destination. Both "aesimc" and "vaesimc" use only two

operands, destination being SSE register, and source being SSE register or

128-bit memory location.

  "aeskeygenassist" is a helper instruction for generating the round key.

It needs three operands: destination being SSE register, source being SSE

register or 128-bit memory, and third operand being 8-bit immediate value.  

The AVX version of this instruction uses the same syntax.  

  The CLMUL extension introduces just one instruction, "pclmulqdq", and its

AVX version as well. This instruction performs a carryless multiplication of

two 64-bit values selected from first and second source according to the bit

fields in immediate value. The destination and first source are SSE registers,

second source is SSE register or 128-bit memory, and immediate value is

provided as last operand. "vpclmulqdq" takes four operands, while "pclmulqdq"

takes only three operands, with the first one serving both the role of

destination and first source.

  The FMA (Fused Multiply-Add) extension introduces additional AVX

instructions which perform multiplication and summation as single operation.

Each one takes three operands, first one serving both the role of destination

and first source, and the following ones being the second and third source.

The mnemonic of FMA instruction is obtained by appending to "vf" prefix: first

either "m" or "nm" to select whether result of multiplication should be taken

as-is or negated, then either "add" or "sub" to select whether third value

will be added to the product or subtracted from the product, then either

"132", "213" or "231" to select which source operands are multiplied and which

one is added or subtracted, and finally the type of data on which the

instruction operates, either "ps", "pd", "ss" or "sd". As it was with SSE

instructions promoted to AVX, instructions operating on packed floating point

values allow 128-bit or 256-bit syntax, in former all the operands are SSE

registers, but the third one can also be a 128-bit memory, in latter the

operands are AVX registers and the third one can also be a 256-bit memory.

Instructions that compute just one floating point result need operands to be

SSE registers, and the third operand can also be a memory, either 32-bit for

single precision or 64-bit for double precision.

 

    vfmsub231ps ymm1,ymm2,ymm3     ; multiply and subtract

    vfnmadd132sd xmm0,xmm5,[ebx]   ; multiply, negate and add        

 

In addition to the instructions created by the rule described above, there are

families of instructions with mnemonics starting with either "vfmaddsub" or

"vfmsubadd", followed by either "132", "213" or "231" and then either "ps" or

"pd" (the operation must always be on packed values in this case). They add

to the result of multiplication or subtract from it depending on the position

of value in packed data - instructions from the "vfmaddsub" group add when the

position is odd and subtract when the position is even, instructions from the

"vfmsubadd" group add when the position is even and subtstract when the

position is odd. The rules for operands are the same as for other FMA

instructions.

  The FMA4 instructions are similar to FMA, but use syntax with four operands

and thus allow destination to be different than all the sources. Their

mnemonics are identical to FMA instructions with the "132", "213" or "231" cut

out, as having separate destination operand makes such selection of operands

superfluous. The multiplication is always performed on values from the first

and second source, and then the value from third source is added or

subtracted. Either second or third source can be a memory operand, and the

rules for the sizes of operands are the same as for FMA instructions.

 

    vfmaddpd ymm0,ymm1,[esi],ymm2  ; multiply and add  

    vfmsubss xmm0,xmm1,xmm2,[ebx]  ; multiply and subtract

   

  The F16C extension consists of two instructions, "vcvtps2ph" and

"vcvtph2ps", which convert floating point values between single precision and

half precision (the 16-bit floating point format). "vcvtps2ph" takes three

operands: destination, source, and rounding controls. The third operand is

always an immediate, the source is either SSE or AVX register containing

single precision values, and the destination is SSE register or memory, the

size of memory is 64 bits when the source is SSE register and 128 bits when

the source is AVX register. "vcvtph2ps" takes two operands, the destination

that can be SSE or AVX register, and the source that is SSE register or memory

with size of the half of destination operand's size.

  The AMD XOP extension introduces a number of new vector instructions with

encoding and syntax analogous to AVX instructions. "vfrczps", "vfrczss",

"vfrczpd" and "vfrczsd" extract fractional portions of single or double

precision values, they all take two operands. The packed operations allow

either SSE or AVX register as destination, for the other two it has to be SSE

register. Source can be register of the same type as destination, or memory

of appropriate size (256-bit for destination being AVX register, 128-bit for

packed operation with destination being SSE register, 64-bit for operation

on a solitary double precision value and 32-bit for operation on a solitary

single precision value).

 

    vfrczps ymm0,[esi]           ; load fractional parts

   

  "vpcmov" copies bits from either first or second source into destination

depending on the values of corresponding bits in the fourth operand (the

selector). If the bit in selector is set, the corresponding bit from first

source is copied into the same position in destination, otherwise the bit from

second source is copied. Either second source or selector can be memory

location, 128-bit or 256-bit depending on whether SSE registers or AVX

registers are specified as the other operands.

 

    vpcmov xmm0,xmm1,xmm2,[ebx]  ; selector in memory

    vpcmov ymm0,ymm5,[esi],ymm2  ; source in memory

 

The family of packed comparison instructions take four operands, the

destination and first source being SSE register, second source being SSE

register or 128-bit memory and the fourth operand being immediate value

defining the type of comparison. The mnemonic or instruction is created

by appending to "vpcom" prefix either "b" or "ub" to compare signed or

unsigned bytes, "w" or "uw" to compare signed or unsigned words, "d" or "ud"

to compare signed or unsigned double words, "q" or "uq" to compare signed or

unsigned quad words. The respective values from the first and second source

are compared and the corresponding data element in destination is set to

either all ones or all zeros depending on the result of comparison. The fourth

operand has to specify one of the eight comparison types (table 2.5). All

these instructions have also variants with only three operands and the type

of comparison encoded within the instruction name by inserting the comparison

mnemonic after "vpcom".

 

    vpcomb   xmm0,xmm1,xmm2,4    ; test for equal bytes

    vpcomgew xmm0,xmm1,[ebx]     ; compare signed words

 

   Table 2.5  XOP comparisons

  ÚÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿

  ³ Code ³ Mnemonic ³ Description             ³

  ÆÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͵

  ³ 0    ³ lt       ³ less than               ³

  ³ 1    ³ le       ³ less than or equal      ³

  ³ 2    ³ gt       ³ greater than            ³

  ³ 3    ³ ge       ³ greater than or equal   ³

  ³ 4    ³ eq       ³ equal                   ³

  ³ 5    ³ neq      ³ not equal               ³

  ³ 6    ³ false    ³ false                   ³

  ³ 7    ³ true     ³ true                    ³

  ÀÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

 

  "vpermil2ps" and "vpermil2pd" set the elements in destination register to

zero or to a value selected from first or second source depending on the

corresponding bit fields from the fourth operand (the selector) and the

immediate value provided in fifth operand. Refer to the AMD manuals for the

detailed explanation of the operation performed by these instructions. Each

of the first four operands can be a register, and either second source or

selector can be memory location, 128-bit or 256-bit depending on whether SSE

registers or AVX registers are used for the other operands.

 

    vpermil2ps ymm0,ymm3,ymm7,ymm2,0  ; permute from two sources

 

  "vphaddbw" adds pairs of adjacent signed bytes to form 16-bit values and

stores them at the same positions in destination. "vphaddubw" does the same

but treats the bytes as unsigned. "vphaddbd" and "vphaddubd" sum all bytes

(either signed or unsigned) in each four-byte block to 32-bit results,

"vphaddbq" and "vphaddubq" sum all bytes in each eight-byte block to

64-bit results, "vphaddwd" and "vphadduwd" add pairs of words to 32-bit

results, "vphaddwq" and "vphadduwq" sum all words in each four-word block to

64-bit results, "vphadddq" and "vphaddudq" add pairs of double words to 64-bit

results. "vphsubbw" subtracts in each two-byte block the byte at higher

position from the one at lower position, and stores the result as a signed

16-bit value at the corresponding position in destination, "vphsubwd"

subtracts in each two-word block the word at higher position from the one at

lower position and makes signed 32-bit results, "vphsubdq" subtract in each

block of two double word the one at higher position from the one at lower

position and makes signed 64-bit results. Each of these instructions takes

two operands, the destination being SSE register, and the source being SSE

register or 128-bit memory.

 

    vphadduwq xmm0,xmm1          ; sum quadruplets of words

 

  "vpmacsww" and "vpmacssww" multiply the corresponding signed 16-bit values

from the first and second source and then add the products to the parallel

values from the third source, then "vpmacsww" takes the lowest 16 bits of the

result and "vpmacssww" saturates the result down to 16-bit value, and they

store the final 16-bit results in the destination. "vpmacsdd" and "vpmacssdd"

perform the analogous operation on 32-bit values. "vpmacswd" and "vpmacsswd" do

the same calculation only on the low 16-bit values from each 32-bit block and

form the 32-bit results. "vpmacsdql" and "vpmacssdql" perform such operation

on the low 32-bit values from each 64-bit block and form the 64-bit results,

while "vpmacsdqh" and "vpmacssdqh" do the same on the high 32-bit values from

each 64-bit block, also forming the 64-bit results. "vpmadcswd" and

"vpmadcsswd" multiply the corresponding signed 16-bit value from the first

and second source, then sum all the four products and add this sum to each

16-bit element from third source, storing the truncated or saturated result

in destination. All these instructions take four operands, the second source

can be 128-bit memory or SSE register, all the other operands have to be

SSE registers.

 

    vpmacsdd xmm6,xmm1,[ebx],xmm6  ; accumulate product

 

  "vpperm" selects bytes from first and second source, optionally applies a

separate transformation to each of them, and stores them in the destination.

The bit fields in fourth operand (the selector) specify for each position in

destination what byte from which source is taken and what operation is applied

to it before it is stored there. Refer to the AMD manuals for the detailed

information about these bit fields. This instruction takes four operands,

either second source or selector can be a 128-bit memory (or they can be SSE

registers both), all the other operands have to be SSE registers.

  "vpshlb", "vpshlw", "vpshld" and "vpshlq" shift logically bytes, words, double

words or quad words respectively. The amount of bits to shift by is specified

for each element separately by the signed byte placed at the corresponding

position in the third operand. The source containing elements to shift is

provided as second operand. Either second or third operand can be 128-bit

memory (or they can be SSE registers both) and the other operands have to be

SSE registers.

 

    vpshld xmm3,xmm1,[ebx]       ; shift bytes from xmm1

 

"vpshab", "vpshaw", "vpshad" and "vpshaq" arithmetically shift bytes, words,

double words or quad words. These instructions follow the same rules as the

logical shifts described above. "vprotb", "vprotw", "vprotd" and "vprotq"

rotate bytes, word, double words or quad words. They follow the same rules as

shifts, but additionally allow third operand to be immediate value, in which

case the same amount of rotation is specified for all the elements in source.

 

    vprotb xmm0,[esi],3          ; rotate bytes to the left

 

  The MOVBE extension introduces just one new instruction, "movbe", which

swaps bytes in value from source before storing it in destination, so can

be used to load and store big endian values. It takes two operands, either

the destination or source should be a 16-bit, 32-bit or 64-bit memory (the

last one being only allowed in long mode), and the other operand should be

a general register of the same size.  

  The BMI extension, consisting of two subsets - BMI1 and BMI2, introduces

new instructions operating on general registers, which use the same encoding

as AVX instructions and so allow the extended syntax. All these instructions

use 32-bit operands, and in long mode they also allow the forms with 64-bit

operands.

  "andn" calculates the bitwise AND of second source with the inverted bits

of first source and stores the result in destination. The destination and

the first source have to be general registers, the second source can be

general register or memory.

 

    andn edx,eax,[ebx]   ; bit-multiply inverted eax with memory

 

  "bextr" extracts from the first source the sequence of bits using an index

and length specified by bit fields in the second source operand and stores

it into destination. The lowest 8 bits of second source specify the position

of bit sequence to extract and the next 8 bits of second source specify the

length of sequence. The first source can be a general register or memory,

the other two operands have to be general registers.

 

    bextr eax,[esi],ecx  ; extract bit field from memory

   

  "blsi" extracts the lowest set bit from the source, setting all the other

bits in destination to zero. The destination must be a general register,

the source can be general register or memory.

 

    blsi rax,r11         ; isolate the lowest set bit      

 

  "blsmsk" sets all the bits in the destination up to the lowest set bit in

the source, including this bit. "blsr" copies all the bits from the source to

destination except for the lowest set bit, which is replaced by zero. These

instructions follow the same rules for operands as "blsi".

  "tzcnt" counts the number of trailing zero bits, that is the zero bits up to

the lowest set bit of source value. This instruction is analogous to "lzcnt"

and follows the same rules for operands, so it also has a 16-bit version,

unlike the other BMI instructions.

  "bzhi" is BMI2 instruction, which copies the bits from first source to

destination, zeroing all the bits up from the position specified by second

source. It follows the same rules for operands as "bextr".

  "pext" uses a mask in second source operand to select bits from first

operands and puts the selected bits as a continuous sequence into destination.

"pdep" performs the reverse operation - it takes sequence of bits from the

first source and puts them consecutively at the positions where the bits in

second source are set, setting all the other bits in destination to zero.

These BMI2 instructions follow the same rules for operands as "andn".    

  "mulx" is a BMI2 instruction which performs an unsigned multiplication of

value from EDX or RDX register (depending on the size of specified operands)

by the value from third operand, and stores the low half of result in the

second operand, and the high half of result in the first operand, and it does

it without affecting the flags. The third operand can be general register or

memory, and both the destination operands have to be general registers.

 

    mulx edx,eax,ecx     ; multiply edx by ecx into edx:eax  

 

  "shlx", "shrx" and "sarx" are BMI2 instructions, which perform logical or

arithmetical shifts of value from first source by the amount specified by

second source, and store the result in destination without affecting the

flags. The have the same rules for operands as "bzhi" instruction.

  "rorx" is a BMI2 instruction which rotates right the value from source

operand by the constant amount specified in third operand and stores the

result in destination without affecting the flags. The destination operand

has to be general register, the source operand can be general register or

memory, and the third operand has to be an immediate value.

 

    rorx eax,edx,7       ; rotate without affecting flags

                     

  The TBM is an extension designed by AMD to supplement the BMI set. The

"bextr" instruction is extended with a new form, in which second source is

a 32-bit immediate value. "blsic" is a new instruction which performs the

same operation as "blsi", but with the bits of result reversed. It uses the

same rules for operands as "blsi". "blsfill" is a new instruction, which takes

the value from source, sets all the bits below the lowest set bit and store

the result in destination, it also uses the same rules for operands as "blsi".

  "blci", "blcic", "blcs", "blcmsk" and "blcfill" are instructions analogous

to "blsi", "blsic", "blsr", "blsmsk" and "blsfill" respectively, but they

perform the bit-inverted versions of the same operations. They follow the

same rules for operands as the instructions they reflect.

  "tzmsk" finds the lowest set bit in value from source operand, sets all bits

below it to 1 and all the rest of bits to zero, then writes the result to

destination. "t1mskc" finds the least significant zero bit in the value from

source  operand, sets the bits below it to zero and all the other bits to 1,

and writes the result to destination. These instructions have the same rules

for operands as "blsi".

     

 

2.1.24  AVX-512 instructions

 

The AVX-512 introduces 512-bit vector registers, which extend the 256-bit

registers used by AVX and AVX2. It also extends the set of vector registers

from 16 to 32, with the additional registers "zmm16" to "zmm31", their low

256-bit portions "ymm16" to "ymm31" and their low 128-bit portions "xmm16"

to "xmm31". These additional registers can only be accessed in the long mode.

 

   Table 2.6  New registers available in long mode with AVX-512

  ÚÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿

  ³ Size    ³ Registers                                              ³

  ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ 128-bit ³ xmm16  xmm17  xmm18  xmm19  xmm20  xmm21  xmm22  xmm23 ³

  ³         ³ xmm24  xmm25  xmm26  xmm27  xmm28  xmm29  xmm30  xmm31 ³

  ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ 256-bit ³ ymm16  ymm17  ymm18  ymm19  ymm20  ymm21  ymm22  ymm23 ³

  ³         ³ ymm24  ymm25  ymm26  ymm27  ymm28  ymm29  ymm30  ymm31 ³

  ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

  ³ 512-bit ³ zmm16  zmm17  zmm18  zmm19  zmm20  zmm21  zmm22  zmm23 ³

  ³         ³ zmm24  zmm25  zmm26  zmm27  zmm28  zmm29  zmm30  zmm31 ³

  ÀÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

 

  In addition to new operand sizes and registers, the AVX-512 introduces

a number of supplementary settings that can be included in the operands

of AVX instructions.

  The destination operand of the most of AVX instructions can be followed

by the name of an opmask register enclosed in braces, this modifier

specifies a mask that decides which units of data in the destination

operand are going to be updated. The "k0" register cannot be used as a

destination mask. This setting can be further followed by "{z}" modifier

to choose that the data units not selected by mask should be zeroed

instead of leaving them unchanged.

 

    vaddpd zmm1{k1},zmm5,zword [rsi]  ; update selected floats

    vaddps ymm6{k1}{z},ymm12,ymm24    ; update selected, zero other ones

 

  When an instruction that operates on packed data has a source operand

loaded from a memory, the memory location may be just a single unit of data

and the source used for the operation is created by broadcasting this

value into all the units within the required size. To specify that such

broadcasting method is used the memory operand should be followed by one

of the "{1to2}", "{1to4}", "{1to8}", "{1to16}", "{1to32}" and "{1to64}"

modifiers, selecting the appropriate multiply of a unit.

 

    vsubps zmm1,zmm2,dword [rsi] {1to16} ; subtract from all floats

 

  When an instruction does not use a memory operand often an additional

operand may follow the source operands, containing the rounding mode

specifier. When an instruction has variants that operate on different

sizes of data, the rounding mode can be specified only when the

register operands are 512-bit.

 

    vdivps zmm2,zmm3,zmm5,{ru-sae}    ; round results up

 

   Table 2.7  AVX-512 rounding modes

  ÚÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿

  ³ Operand  ³ Description                                   ³

  ÆÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͵

  ³ {rn-sae} ³ round to nearest and suppress all exceptions  ³

  ³ {rd-sae} ³ round down and suppress all exceptions        ³

  ³ {ru-sae} ³ round up and suppress all exceptions          ³

  ³ {rz-sae} ³ round toward zero and suppress all exceptions ³

  ÀÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

 

Some of the instructions do not use a rounding mode but still allow

to specify the exception suppression option with "{sae}" modifier in the

additional operand.

 

    vmaxpd zmm0,zmm1,zmm2,{sae}       ; suppress all exceptions

 

  The family of "gather" instructions in their AVX-512 variants use a new

syntax with only two operands. The opmask register takes the role which

was played by the third operand in the AVX2 syntax and it is mandatory

in this case.

 

    vgatherdps xmm0{k1},[eax+xmm1]    ; gather four floats

    vgatherdpd zmm0{k3},[ymm3*8]      ; gather eight doubles

 

  The new family of "scatter" instructions perform an operation reverse to

the one of "gather". They also take two operands, the destination is a

memory with vector indexing and opmask modifier, and the source is a vector

register.

 

    vscatterdps [eax+xmm1]{k1},xmm0    ; scatter four floats

    vscatterdpd [ymm3*8]{k3},zmm0      ; scatter eight doubles

 

  The AVX512_4VNNI extension introduces instructions with another unusual

syntax variant. The first source operand of "vp4dpwssd" or "vp4dpwssds"

instruction refers to an aligned block of four 512-bit registers, containing

the base register specified by the operand. This can be indicated by attaching

"+3" to the name of register, although it is optional.

 

    vp4dpwssd zmm1{k1}{z},zmm2+3,xword[rbx]

 

 

2.1.25  Other extensions of instruction set

 

There is a number of additional instruction set extensions recognized by flat

assembler, and examples of syntax of the instructions introduced by those

extensions are provided here. For a detailed information on the operations

performed by them, check out the manuals from Intel or AMD.

  The Virtual-Machine Extensions (VMX) provide a set of instructions for the

management of virtual machines. The "vmxon" instruction, which enters the VMX

operation, requires a single 64-bit memory operand, which should be a physical

address of memory region, which the logical processor may use to support VMX

operation. The "vmxoff" instruction, which leaves the VMX operation, has no

operands. The "vmlaunch" and "vmresume", which launch or resume the virtual

machines, and "vmcall", which allows guest software to call the VM monitor,

use no operands either.

  The "vmptrld" loads the physical address of current Virtual Machine Control

Structure (VMCS) from its memory operand, "vmptrst" stores the pointer to

current VMCS into address specified by its memory operand, and "vmclear" sets

the launch state of the VMCS referenced by its memory operand to clear. These

three instruction all require single 64-bit memory operand.

  The "vmread" reads from VCMS a field specified by the source operand and

stores it into the destination operand. The source operand should be a

general purpose register, and the destination operand can be a register of

memory. The "vmwrite" writes into a VMCS field specified by the destination

operand the value provided by source operand. The source operand can be a

general purpose register or memory, and the destination operand must be a

register. The size of operands for those instructions should be 64-bit when

in long mode, and 32-bit otherwise.

  The "invept" and "invvpid" invalidate the translation lookaside buffers

(TLBs) and paging-structure caches, either derived from extended page tables

(EPT), or based on the virtual processor identifier (VPID). These instructions

require two operands, the first one being the general purpose register

specifying the type of invalidation, and the second one being a 128-bit

memory operand providing the invalidation descriptor. The first operand

should be a 64-bit register when in long mode, and 32-bit register otherwise.

  The Safer Mode Extensions (SMX) provide the functionalities available

throught the "getsec" instruction. This instruction takes no operands, and

the function that is executed is determined by the contents of EAX register

upon executing this instruction.

  The Secure Virtual Machine (SVM) is a variant of virtual machine extension

used by AMD. The "skinit" instruction securely reinitializes the processor

allowing the startup of trusted software, such as the virtual machine monitor

(VMM). This instruction takes a single operand, which must be EAX, and

provides a physical address of the secure loader block (SLB).

  The "vmrun" instruction is used to start a guest virtual machine,

its only operand should be an accumulator register (AX, EAX or RAX, the

last one available only in long mode) providing the physical address of the

virtual machine control block (VMCB). The "vmsave" stores a subset of

processor state into VMCB specified by its operand, and "vmload" loads the

same subset of processor state from a specified VMCB. The same operand rules

as for the "vmrun" apply to those two instructions.

  "vmmcall" allows the guest software to call the VMM. This instruction takes

no operands.

  "stgi" set the global interrupt flag to 1, and "clgi" zeroes it. These

instructions take no operands.

  "invlpga" invalidates the TLB mapping for a virtual page specified by the

first operand (which has to be accumulator register) and address space

identifier specified by the second operand (which must be ECX register).

  The XSAVE set of instructions allows to save and restore processor state

components. "xsave" and "xsaveopt" store the components of processor state

defined by bit mask in EDX and EAX registers into area defined by memory

operand. "xrstor" restores from the area specified by memory operand the

components of processor state defined by mask in EDX and EAX. The "xsave64",

"xsaveopt64" and "xrstor64" are 64-bit versions of these instructions, allowed

only in long mode.

  "xgetbv" read the contents of 64-bit XCR (extended control register)

specified in ECX register into EDX and EAX registers. "xsetbv" writes the

contents of EDX and EAX into the 64-bit XCR specified by ECX register. These

instructions have no operands.

  The RDRAND extension introduces one new instruction, "rdrand", which loads

the hardware-generated random value into general register. It takes one

operand, which can be 16-bit, 32-bit or 64-bit register (with the last one

being allowed only in long mode).

  The FSGSBASE extension adds long mode instructions that allow to read and

write the segment base registers for FS and GS segments. "rdfsbase" and

"rdgsbase" read the corresponding segment base registers into operand, while

"wrfsbase" and "wrgsbase" write the value of operand into those register.

All these instructions take one operand, which can be 32-bit or 64-bit general

register.  

  The INVPCID extension adds "invpcid" instruction, which invalidates mapping

in the TLBs and paging caches based on the invalidation type specified in

first operand and PCID invalidate descriptor specified in second operand.

The first operands should be 32-bit general register when not in long mode,

or 64-bit general register when in long mode. The second operand should be

128-bit memory location.  

  The HLE and RTM extensions provide set of instructions for the transactional

management. The "xacquire" and "xrelease" are new prefixes that can be used

with some of the instructions to start or end lock elision on the memory

address specified by prefixed instruction. The "xbegin" instruction starts

the transactional execution, its operand is the address a fallback routine

that gets executes in case of transaction abort, specified like the operand

for near jump instruction. "xend" marks the end of transcational execution

region, it takes no operands. "xabort" forces the transaction abort, it takes

an 8-bit immediate value as its only operand, this value is passed in the

highest bits of EAX to the fallback routine. "xtest" checks whether there is

transactional execution in progress, this instruction takes no operands.

  The MPX extension adds instructions that operate on new bounds registers

and aid in checking the memory references. For some of these instructions

flat assemblers allows a special syntax that allows a fine control over their

operation, where an address of a memory operand is separated into two parts

with a comma. With "bndmk" instruction the first part of such address specifies

the lower bound and the second one the upper bound. The lower bound can be

either zero or a register, the upper bound can be any address that uses no more

than one register (multiplied by 1, 2, 4, or 8). The addressing registers need

to be 64-bit when in long mode, and 32-bit otherwise.

 

    bndmk bnd0,[rbx,100000h] ; lower bound in register, upper directly

    bndmk bnd1,[0,rbx]       ; lower bound zero, upper in register

 

In case of "bndldx" and "bndstx", the first part of memory operand specifies an

address used to access a bound table entry, while the second part is either zero

or a register that plays a role of an additional operand for such instruction.

The address in the first part may use no more than one register and the register

cannot be multiplied by a number other than 1.

 

    bndstx [rcx,rsi],bnd3  ; store bnd3 and rsi at rcx in the bound table

    bndldx bnd2,[rcx,rsi]  ; load from bound table if entry matches rsi

 

 

2.2  Control directives

 

This section describes the directives that control the assembly process, they

are processed during the assembly and may cause some blocks of instructions

to be assembled differently or not assembled at all.

 

 

2.2.1  Numerical constants

 

The "=" directive allows to define the numerical constant. It should be

preceded by the name for the constant and followed by the numerical expression

providing the value. The value of such constants can be a number or an address,

but - unlike labels - the numerical constants are not allowed to hold the

register-based addresses. Besides this difference, in their basic variant

numerical constants behave very much like labels and you can even

forward-reference them (access their values before they actually get defined).

  There is, however, a second variant of numerical constants, which is

recognized by assembler when you try to define the constant of name, under

which there already was a numerical constant defined. In such case assembler

treats that constant as an assembly-time variable and allows it to be assigned

with new value, but forbids forward-referencing it (for obvious reasons). Let's

see both the variant of numerical constants in one example:

 

    dd sum

    x = 1

    x = x+2

    sum = x

 

Here the "x" is an assembly-time variable, and every time it is accessed, the

value that was assigned to it the most recently is used. Thus if we tried to

access the "x" before it gets defined the first time, like if we wrote "dd x"

in place of the "dd sum" instruction, it would cause an error. And when it is

re-defined with the "x = x+2" directive, the previous value of "x" is used to

calculate the new one. So when the "sum" constant gets defined, the "x" has

value of 3, and this value is assigned to the "sum". Since this one is defined

only once in source, it is the standard numerical constant, and can be

forward-referenced. So the "dd sum" is assembled as "dd 3". To read more about

how the assembler is able to resolve this, see section 2.2.6.

  The value of numerical constant can be preceded by size operator, which can

ensure that the value will fit in the range for the specified size, and can

affect also how some of the calculations inside the numerical expression are

performed. This example:

 

    c8 = byte -1

    c32 = dword -1

 

defines two different constants, the first one fits in 8 bits, the second one

fits in 32 bits.

  When you need to define constant with the value of address, which may be

register-based (and thus you cannot employ numerical constant for this

purpose), you can use the extended syntax of "label" directive (already

described in section 1.2.3), like:

 

    label myaddr at ebp+4

 

which declares label placed at "ebp+4" address. However remember that labels,

unlike numerical constants, cannot become assembly-time variables.

 

 

2.2.2  Conditional assembly

 

"if" directive causes some block of instructions to be assembled only under

certain condition. It should be followed by logical expression specifying the

condition, instructions in next lines will be assembled only when this

condition is met, otherwise they will be skipped. The optional "else if"

directive followed with logical expression specifying additional condition

begins the next block of instructions that will be assembled if previous

conditions were not met, and the additional condition is met. The optional

"else" directive begins the block of instructions that will be assembled if

all the conditions were not met. The "end if" directive ends the last block of

instructions.

  You should note that "if" directive is processed at assembly stage and

therefore it doesn't affect any preprocessor directives, like the definitions

of symbolic constants and macroinstructions - when the assembler recognizes the

"if" directive, all the preprocessing has been already finished.

  The logical expression consist of logical values and logical operators. The

logical operators are "~" for logical negation, "&" for logical and, "|" for

logical or. The negation has the highest priority. Logical value can be a

numerical expression, it will be false if it is equal to zero, otherwise it

will be true. Two numerical expression can be compared using one of the

following operators to make the logical value: "=" (equal), "<" (less),

">" (greater), "<=" (less or equal), ">=" (greater or equal),

"<>" (not equal).

  The "used" operator followed by a symbol name, is the logical value that

checks whether the given symbol is used somewhere (it returns correct result

even if symbol is used only after this check). The "defined" operator can be

followed by any expression, usually just by a single symbol name; it checks

whether the given expression contains only symbols that are defined in the

source and accessible from the current position. The "definite" operator

does a similar check with restriction to symbols defined before current

position in source.

  With "relativeto" operator it is possible to check whether values of two

expressions differ only by constant amount. The valid syntax is a numerical

expression followed by "relativeto" and then another expression (possibly

register-based). Labels that have no simple numerical value can be tested

this way to determine what kind of operations may be possible with them.

  The following simple example uses the "count" constant that should be

defined somewhere in source:

 

    if count>0

        mov cx,count

        rep movsb

    end if

 

These two assembly instructions will be assembled only if the "count" constant

is greater than 0. The next sample shows more complex conditional structure:

 

    if count & ~ count mod 4

        mov cx,count/4

        rep movsd

    else if count>4

        mov cx,count/4

        rep movsd

        mov cx,count mod 4

        rep movsb

    else

        mov cx,count

        rep movsb

    end if

 

The first block of instructions gets assembled when the "count" is non zero and

divisible by four, if this condition is not met, the second logical expression,

which follows the "else if", is evaluated and if it's true, the second block

of instructions get assembled, otherwise the last block of instructions, which

follows the line containing only "else", is assembled.

  There are also operators that allow comparison of values being any chains of

symbols. The "eq" compares whether two such values are exactly the same.

The "in" operator checks whether given value is a member of the list of values

following this operator, the list should be enclosed between "<" and ">"

characters, its members should be separated with commas. The symbols are

considered the same when they have the same meaning for the assembler - for

example "pword" and "fword" for assembler are the same and thus are not

distinguished by the above operators. In the same way "16 eq 10h" is the true

condition, however "16 eq 10+4" is not.

  The "eqtype" operator checks whether the two compared values have the same

structure, and whether the structural elements are of the same type. The

distinguished types include numerical expressions, individual quoted strings,

floating point numbers, address expressions (the expressions enclosed in square

brackets or preceded by "ptr" operator), instruction mnemonics, registers, size

operators, jump type and code type operators. And each of the special

characters that act as a separators, like comma or colon, is the separate type

itself. For example, two values, each one consisting of register name followed

by comma and numerical expression, will be regarded as of the same type, no

matter what kind of register and how complicated numerical expression is used;

with exception for the quoted strings and floating point values, which are the

special kinds of numerical expressions and are treated as different types. Thus

"eax,16 eqtype fs,3+7" condition is true, but "eax,16 eqtype eax,1.6" is false.

 

 

2.2.3 Repeating blocks of instructions

 

"times" directive repeats one instruction specified number of times. It

should be followed by numerical expression specifying number of repeats and

the instruction to repeat (optionally colon can be used to separate number and

instruction). When special symbol "%" is used inside the instruction, it is

equal to the number of current repeat. For example "times 5 db %" will define

five bytes with values 1, 2, 3, 4, 5. Recursive use of "times" directive is

also allowed, so "times 3 times % db %" will define six bytes with values

1, 1, 2, 1, 2, 3.

  "repeat" directive repeats the whole block of instructions. It should be

followed by numerical expression specifying number of repeats. Instructions

to repeat are expected in next lines, ended with the "end repeat" directive,

for example:

 

    repeat 8

        mov byte [bx],%

        inc bx

    end repeat

 

The generated code will store byte values from one to eight in the memory

addressed by BX register.

  Number of repeats can be zero, in that case the instructions are not

assembled at all.

  The "break" directive allows to stop repeating earlier and continue assembly

from the first line after the "end repeat". Combined with the "if" directive it

allows to stop repeating under some special condition, like:

 

    s = x/2

    repeat 100

        if x/s = s

            break

        end if

        s = (s+x/s)/2

    end repeat

 

  The "while" directive repeats the block of instructions as long as the

condition specified by the logical expression following it is true. The block

of instructions to be repeated should end with the "end while" directive.

Before each repetition the logical expression is evaluated and when its value

is false, the assembly is continued starting from the first line after the

"end while". Also in this case the "%" symbol holds the number of current

repeat. The "break" directive can be used to stop this kind of loop in the same

way as with "repeat" directive. The previous sample can be rewritten to use the

"while" instead of "repeat" this way:

 

    s = x/2

    while x/s <> s

        s = (s+x/s)/2

        if % = 100

            break

        end if

    end while

 

  The blocks defined with "if", "repeat" and "while" can be nested in any

order, however they should be closed in the same order in which they were

started. The "break" directive always stops processing the block that was

started last with either the "repeat" or "while" directive.

 

 

2.2.4  Addressing spaces

 

  "org" directive sets address at which the following code is expected to

appear in memory. It should be followed by numerical expression specifying

the address. This directive begins the new addressing space, the following

code itself is not moved in any way, but all the labels defined within it

and the value of "$" symbol are affected as if it was put at the given

address. However it's the responsibility of programmer to put the code at

correct address at run-time.

  The "load" directive allows to define constant with a binary value loaded

from the already assembled code. This directive should be followed by the name

of the constant, then optionally size operator, then "from" operator and a

numerical expression specifying a valid address in current addressing space.

The size operator has unusual meaning in this case - it states how many bytes

(up to 8) have to be loaded to form the binary value of constant. If no size

operator is specified, one byte is loaded (thus value is in range from 0 to

255). The loaded data cannot exceed current offset.

  The "store" directive can modify the already generated code by replacing

some of the previously generated data with the value defined by given

numerical expression, which follows. The expression can be preceded by the

optional size operator to specify how large value the expression defines, and

therefore how much bytes will be stored, if there is no size operator, the

size of one byte is assumed. Then the "at" operator and the numerical

expression defining the valid address in current addressing code space, at

which the given value have to be stored should follow. This is a directive for

advanced appliances and should be used carefully.

  Both "load" and "store" directives in their basic variant (defined above)

are limited to operate on places in current addressing space. The "$$" symbol

is always equal to the base address of current addressing space, and the "$"

symbol is the address of current position in that addressing space, therefore

these two values define limits of the area, where "load" and "store" can

operate.

  Combining the "load" and "store" directives allows to do things like encoding

some of the already generated code. For example to encode the whole code

generated in current addressing space you can use such block of directives:

 

    repeat $-$$

        load a byte from $$+%-1

        store byte a xor c at $$+%-1

    end repeat

 

and each byte of code will be xored with the value defined by "c" constant.

  "virtual" defines virtual data at specified address. This data will not be

included in the output file, but labels defined there can be used in other

parts of source. This directive can be followed by "at" operator and the

numerical expression specifying the address for virtual data, otherwise is

uses current address, the same as "virtual at $". Instructions defining data

are expected in next lines, ended with "end virtual" directive. The block of

virtual instructions itself is an independent addressing space, after it's

ended, the context of previous addressing space is restored.

  The "virtual" directive can be used to create union of some variables, for

example:

 

    GDTR dp ?

    virtual at GDTR

        GDT_limit dw ?

        GDT_address dd ?

    end virtual

 

It defines two labels for parts of the 48-bit variable at "GDTR" address.

  It can be also used to define labels for some structures addressed by a

register, for example:

 

    virtual at bx

        LDT_limit dw ?

        LDT_address dd ?

    end virtual

 

With such definition instruction "mov ax,[LDT_limit]" will be assembled

to the same instruction as "mov ax,[bx]".

  Declaring defined data values or instructions inside the virtual block could

also be useful, because the "load" directive may be used to load the values

from the virtually generated code into a constants. This directive in its basic

version should be used after the code it loads but before the virtual block

ends, because it can only load the values from the same addressing space. For

example:

 

    virtual at 0

        xor eax,eax

        and edx,eax

        load zeroq dword from 0

    end virtual

 

The above piece of code will define the "zeroq" constant containing four bytes

of the machine code of the instructions defined inside the virtual block.

This method can be also used to load some binary value from external file.

For example this code:

 

    virtual at 0

        file 'a.txt':10h,1

        load char from 0

    end virtual

 

loads the single byte from offset 10h in file "a.txt" into the "char"

constant.

  Instead of or in addition to an "at" argument, "virtual" can also be followed

by an "as" keyword and a string defining an extension of additional file where

the initialized content of the addressing space started by "virtual" is going

to be stored at the end of a successful assembly.

 

    virtual at 0 as 'asc'

        times 256 db %-1

    end virtual

 

  Any of the "section" directives described in 2.4 also begins a new

addressing space.

  It is possible to declare a special kind of label that marks the current

addressing space, by appending a double colon instead of a single one after a

label name. This symbol cannot then be used in numerical expressions, the only

place where it is allowed to use it is the extended syntax of "load" and

"store" directives. It is possible to make these directives operate on a

different addressing space than the current one, by specifying address with

the two components: first the name of a special label that marks the

addressing space, followed by the colon character and a numerical expression

defining a valid address inside that addressing space. In the following

example this extended syntax is used to load the value from a block after it

has been closed:

 

    virtual at 0

        hex_digits::

        db '0123456789ABCDEF'

    end virtual

    load a byte from hex_digits:10

 

  This way it is possible to operate on values inside any code block,

including all the ones defined with "virtual". However it is not allowed to

specify addressing space that has not been assembled yet, just as it is not

allowed to specify an address in the current addressing space that exceeds

the current offset. The addresses in any other addressing space are also

limited by the boundaries of the block.

  The "virtual" directive can have a previously defined addressing space

label as the only argument. This variant allows to extend a previously defined

and closed block with additional data. Any definition of data within

an extending block is going to have the same effect as if that definition was

present in the original "virtual" block.

 

    virtual at 0 as 'log'

        Log::

    end virtual

 

    virtual Log

        db 'Hello!',13,10

    end virtual

 

 

2.2.5  Other directives

 

"align" directive aligns code or data to the specified boundary. It should

be followed by a numerical expression specifying the number of bytes, to the

multiply of which the current address has to be aligned. The boundary value

has to be the power of two.

  The "align" directive fills the bytes that had to be skipped to perform the

alignment with the "nop" instructions and at the same time marks this area as

uninitialized data, so if it is placed among other uninitialized data that

wouldn't take space in the output file, the alignment bytes will act the same

way. If you need to fill the alignment area with some other values, you can

combine "align" with "virtual" to get the size of alignment needed and then

create the alignment yourself, like:

 

    virtual

        align 16

        a = $ - $$

    end virtual

    db a dup 0

 

The "a" constant is defined to be the difference between address after

alignment and address of the "virtual" block (see previous section), so it is

equal to the size of needed alignment space.

  "display" directive displays the message at the assembly time. It should

be followed by the quoted strings or byte values, separated with commas. It

can be used to display values of some constants, for example:

 

    bits = 16

    display 'Current offset is 0x'

    repeat bits/4

        d = '0' + $ shr (bits-%*4) and 0Fh

        if d > '9'

            d = d + 'A'-'9'-1

        end if

        display d

    end repeat

    display 13,10

 

This block of directives calculates the four hexadecimal digits of 16-bit

value and converts them into characters for displaying. Note that this will

not work if the adresses in current addressing space are relocatable (as it

might happen with PE or object output formats), since only absolute values can

be used this way. The absolute value may be obtained by calculating the

relative address, like "$-$$", or "rva $" in case of PE format.

  The "err" directive immediately terminates the assembly process when it is

encountered by assembler.

  The "assert" directive tests whether the logical expression that follows it

is true, and if not, it signalizes the error.

 

 

2.2.6  Multiple passes

 

Because the assembler allows to reference some of the labels or constants

before they get actually defined, it has to predict the values of such labels

and if there is even a suspicion that prediction failed in at least one case,

it does one more pass, assembling the whole source, this time doing better

prediction based on the values the labels got in the previous pass.

  The changing values of labels can cause some instructions to have encodings

of different length, and this can cause the change in values of labels again.

And since the labels and constants can also be used inside the expressions that

affect the behavior of control directives, the whole block of source can be

processed completely differently during the new pass. Thus the assembler does

more and more passes, each time trying to do better predictions to approach

the final solution, when all the values get predicted correctly. It uses

various method for predicting the values, which has been chosen to allow

finding in a few passes the solution of possibly smallest length for the most

of the programs.

  Some of the errors, like the values not fitting in required boundaries, are

not signaled during those intermediate passes, since it may happen that when

some of the values are predicted better, these errors will disappear. However

if assembler meets some illegal syntax construction or unknown instruction, it

always stops immediately. Also defining some label more than once causes such

error, because it makes the predictions groundless.

  Only the messages created with the "display" directive during the last

performed pass get actually displayed. In case when the assembly has been

stopped due to an error, these messages may reflect the predicted values that

are not yet resolved correctly.

  The solution may sometimes not exist and in such cases the assembler will

never manage to make correct predictions - for this reason there is a limit for

a number of passes, and when assembler reaches this limit, it stops and

displays the message that it is not able to generate the correct output.

Consider the following example:

 

    if ~ defined alpha

        alpha:

    end if

 

The "defined" operator gives the true value when the expression following it

could be calculated in this place, what in this case means that the "alpha"

label is defined somewhere. But the above block causes this label to be defined

only when the value given by "defined" operator is false, what leads to an

antynomy and makes it impossible to resolve such code. When processing the "if"

directive assembler has to predict whether the "alpha" label will be defined

somewhere (it wouldn't have to predict only if the label was already defined

earlier in this pass), and whatever the prediction is, the opposite always

happens. Thus the assembly will fail, unless the "alpha" label is defined

somewhere in source preceding the above block of instructions - in such case,

as it was already noted, the prediction is not needed and the block will just

get skipped.

  The above sample might have been written as a try to define the label only

when it was not yet defined. It fails, because the "defined" operator does

check whether the label is defined anywhere, and this includes the definition

inside this conditionally processed block. It could be easily corrected by

using "definite" operator instead of "defined". But there is also another

modification that could get it resolved:

 

    if ~ defined alpha | defined @f

        alpha:

        @@:

    end if

 

The "@f" is always the same label as the nearest "@@" symbol in the source

following it, so the above sample would mean the same if any unique name was

used instead of the anonymous label. When "alpha" is not defined in any other

place in source, the only possible solution is when this block gets defined,

and this time this doesn't lead to the antynomy, because of the anonymous

label which makes this block self-establishing. To better understand this,

look at the blocks that has nothing more than this self-establishing:

 

    if defined @f

        @@:

    end if

 

This is an example of source that may have more than one solution, as both

cases when this block gets processed or not are equally correct. Which one of

those two solutions we get depends on the algorithm on the assembler, in case

of flat assembler - on the algorithm of predictions. Back to the previous

sample, when "alpha" is not defined anywhere else, the condition for "if" block

cannot be false, so we are left with only one possible solution, and we can

hope the assembler will arrive at it. On the other hand, when "alpha" is

defined in some other place, we've got two possible solutions again, but one of

them causes "alpha" to be defined twice, and such an error causes assembler to

abort the assembly immediately, as this is the kind of error that deeply

disturbs the process of resolving. So we can get such source either correctly

resolved or causing an error, and what we get may depend on the internal

choices made by the assembler.

  However there are some facts about such choices that are certain. When

assembler has to check whether the given symbol is defined and it was already

defined in the current pass, no prediction is needed - it was already noted

above. And when the given symbol has been defined never before, including all

the already finished passes, the assembler predicts it to be not defined.

Knowing this, we can expect that the simple self-establishing block shown

above will not be assembled at all and that the previous sample will resolve

correctly when "alpha" is defined somewhere before our conditional block,

while it will itself define "alpha" when it's not already defined earlier, thus

potentially causing the error because of double definition if the "alpha" is

also defined somewhere later.

  The "used" operator may be expected to behave in a similar manner in

analogous cases, however any other kinds of predictions may not be so simple and

you should never rely on them this way.

  The "err" directive, usually used to stop the assembly when some condition is

met, stops the assembly immediately, regardless of whether the current pass

is final or intermediate. So even when the condition that caused this directive

to be interpreted is mispredicted and temporary, and would eventually disappear

in the later passes, the assembly is stopped anyway.

  The "assert" directive signalizes the error only if its expression is false

after all the symbols have been resolved. You can use "assert 0" in place of

"err" when you do not want to have assembly stopped during the intermediate

passes.

 

 

2.3  Preprocessor directives

 

All preprocessor directives are processed before the main assembly process,

and therefore are not affected by the control directives. At this time also

all comments are stripped out.

 

 

2.3.1  Including source files

 

"include" directive includes the specified source file at the position where

it is used. It should be followed by the quoted name of file that should be

included, for example:

 

    include 'macros.inc'

 

The whole included file is preprocessed before preprocessing the lines next

to the line containing the "include" directive. There are no limits to the

number of included files as long as they fit in memory.

  The quoted path can contain environment variables enclosed within "%"

characters, they will be replaced with their values inside the path, both the

"\" and "/" characters are allowed as a path separators. The file is first

searched for in the directory containing file which included it and when it is

not found there, the search is continued in the directories specified in the

environment variable called INCLUDE (the multiple paths separated with

semicolons can be defined there, they will be searched in the same order as

specified). If file was not found in any of these places, preprocessor looks

for it in the directory containing the main source file (the one specified in

command line). These rules concern also paths given with the "file" directive.

 

 

2.3.2  Symbolic constants

 

The symbolic constants are different from the numerical constants, before the

assembly process they are replaced with their values everywhere in source

lines after their definitions, and anything can become their values.

  The definition of symbolic constant consists of name of the constant

followed by the "equ" directive. Everything that follows this directive will

become the value of constant. If the value of symbolic constant contains

other symbolic constants, they are replaced with their values before assigning

this value to the new constant. For example:

 

    d equ dword

    NULL equ d 0

    d equ edx

 

After these three definitions the value of "NULL" constant is "dword 0" and

the value of "d" is "edx". So, for example, "push NULL" will be assembled as

"push dword 0" and "push d" will be assembled as "push edx". And if then the

following line was put:

 

    d equ d,eax

 

the "d" constant would get the new value of "edx,eax". This way the growing

lists of symbols can be defined.

  "restore" directive allows to get back previous value of redefined symbolic

constant. It should be followed by one more names of symbolic constants,

separated with commas. So "restore d" after the above definitions will give

"d" constant back the value "edx", the second one will restore it to value

"dword", and one more will revert "d" to original meaning as if no such

constant was defined. If there was no constant defined of given name,

"restore" will not cause an error, it will be just ignored.

  Symbolic constant can be used to adjust the syntax of assembler to personal

preferences. For example the following set of definitions provides the handy

shortcuts for all the size operators: