;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; Copyright (C) KolibriOS team 2004-2010. All rights reserved. ;;
;; Distributed under terms of the GNU General Public License ;;
;; ;;
;; Realtek 8139 driver for KolibriOS ;;
;; ;;
;; based on RTL8139.asm driver for menuetos ;;
;; and realtek8139.asm for SolarOS by Eugen Brasoveanu ;;
;; ;;
;; Written by hidnplayr@kolibrios.org ;;
;; ;;
;; GNU GENERAL PUBLIC LICENSE ;;
;; Version 2, June 1991 ;;
;; ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
format MS COFF
API_VERSION equ 0x01000100
DRIVER_VERSION equ 5
MAX_DEVICES equ 16
RBLEN equ 3 ; Receive buffer size: 0==8K 1==16k 2==32k 3==64k
DEBUG equ 1
__DEBUG__ equ 1
__DEBUG_LEVEL__ equ 2
include 'proc32.inc'
include 'imports.inc'
include 'fdo.inc'
include 'netdrv.inc'
public START
public service_proc
public version
REG_IDR0 equ 0x00
REG_MAR0 equ 0x08 ; multicast filter register 0
REG_MAR4 equ 0x0c ; multicast filter register 4
REG_TSD0 equ 0x10 ; transmit status of descriptor
REG_TSAD0 equ 0x20 ; transmit start address of descriptor
REG_RBSTART equ 0x30 ; RxBuffer start address
REG_COMMAND equ 0x37 ; command register
REG_CAPR equ 0x38 ; current address of packet read (word) R/W
REG_IMR equ 0x3c ; interrupt mask register
REG_ISR equ 0x3e ; interrupt status register
REG_TXCONFIG equ 0x40 ; transmit configuration register
REG_RXCONFIG equ 0x44 ; receive configuration register 0
REG_MPC equ 0x4c ; missed packet counter
REG_9346CR equ 0x50 ; serial eeprom 93C46 command register
REG_CONFIG1 equ 0x52 ; configuration register 1
REG_MSR equ 0x58
REG_CONFIG4 equ 0x5a ; configuration register 4
REG_HLTCLK equ 0x5b ; undocumented halt clock register
REG_BMCR equ 0x62 ; basic mode control register
REG_ANAR equ 0x66 ; auto negotiation advertisement register
REG_9346CR_WE equ 11b SHL 6
BIT_RUNT equ 4 ; total packet length < 64 bytes
BIT_LONG equ 3 ; total packet length > 4k
BIT_CRC equ 2 ; crc error occured
BIT_FAE equ 1 ; frame alignment error occured
BIT_ROK equ 0 ; received packet is ok
BIT_RST equ 4 ; reset bit
BIT_RE equ 3 ; receiver enabled
BIT_TE equ 2 ; transmitter enabled
BUFE equ 1 ; rx buffer is empty, no packet stored
BIT_ISR_TOK equ 2 ; transmit ok
BIT_ISR_RER equ 1 ; receive error interrupt
BIT_ISR_ROK equ 0 ; receive ok
BIT_TX_MXDMA equ 8 ; Max DMA burst size per Tx DMA burst
BIT_TXRR equ 4 ; Tx Retry count 16+(TXRR*16)
BIT_RXFTH equ 13 ; Rx fifo threshold
BIT_RBLEN equ 11 ; Ring buffer length indicator
BIT_RX_MXDMA equ 8 ; Max DMA burst size per Rx DMA burst
BIT_NOWRAP equ 7 ; transfered data wrapping
BIT_9356SEL equ 6 ; eeprom selector 9346/9356
BIT_AER equ 5 ; accept error packets
BIT_AR equ 4 ; accept runt packets
BIT_AB equ 3 ; accept broadcast packets
BIT_AM equ 2 ; accept multicast packets
BIT_APM equ 1 ; accept physical match packets
BIT_AAP equ 0 ; accept all packets
BIT_93C46_EEM1 equ 7 ; RTL8139 eeprom operating mode1
BIT_93C46_EEM0 equ 6 ; RTL8139 eeprom operating mode0
BIT_93C46_EECS equ 3 ; chip select
BIT_93C46_EESK equ 2 ; serial data clock
BIT_93C46_EEDI equ 1 ; serial data input
BIT_93C46_EEDO equ 0 ; serial data output
BIT_LWACT equ 4 ; see REG_CONFIG1
BIT_SLEEP equ 1 ; sleep bit at older chips
BIT_PWRDWN equ 0 ; power down bit at older chips
BIT_PMEn equ 0 ; power management enabled
BIT_LWPTN equ 2 ; see REG_CONFIG4
BIT_ERTXTH equ 16 ; early TX threshold
BIT_TOK equ 15 ; transmit ok
BIT_OWN equ 13 ; tx DMA operation is completed
BIT_ANE equ 12 ; auto negotiation enable
BIT_TXFD equ 8 ; 100base-T full duplex
BIT_TX equ 7 ; 100base-T
BIT_10FD equ 6 ; 10base-T full duplex
BIT_10 equ 5 ; 10base-T
BIT_SELECTOR equ 0 ; binary encoded selector CSMA/CD=00001
BIT_IFG1 equ 25
BIT_IFG0 equ 24
TXRR equ 8 ; total retries = 16+(TXRR*16)
TX_MXDMA equ 6 ; 0=16 1=32 2=64 3=128 4=256 5=512 6=1024 7=2048
ERTXTH equ 8 ; in unit of 32 bytes e.g:(8*32)=256
RX_MXDMA equ 7 ; 0=16 1=32 2=64 3=128 4=256 5=512 6=1024 7=unlimited
RXFTH equ 7 ; 0=16 1=32 2=64 3=128 4=256 5=512 6=1024 7=no threshold
RX_CONFIG equ (RBLEN shl BIT_RBLEN) or \
(RX_MXDMA shl BIT_RX_MXDMA) or \
(1 shl BIT_NOWRAP) or \
(RXFTH shl BIT_RXFTH) or\
(1 shl BIT_AB) or \ ; Accept broadcast packets
(1 shl BIT_APM) or \ ; Accept physical match packets
(1 shl BIT_AER) or \ ; Accept error packets
(1 shl BIT_AR) or \ ; Accept Runt packets (smaller then 64 bytes)
(1 shl BIT_AM) ; Accept multicast packets
RX_BUFFER_SIZE equ (8192 shl RBLEN);+16
MAX_ETH_FRAME_SIZE equ 1516 ; exactly 1514 wthout CRC
NUM_TX_DESC equ 4
EE_93C46_REG_ETH_ID equ 7 ; MAC offset
EE_93C46_READ_CMD equ (6 shl 6) ; 110b + 6bit address
EE_93C56_READ_CMD equ (6 shl 8) ; 110b + 8bit address
EE_93C46_CMD_LENGTH equ 9 ; start bit + cmd + 6bit address
EE_93C56_CMD_LENGTH equ 11 ; start bit + cmd + 8bit ddress
VER_RTL8139 equ 1100000b
VER_RTL8139A equ 1110000b
VER_RTL8139AG equ 1110100b
VER_RTL8139B equ 1111000b
VER_RTL8130 equ VER_RTL8139B
VER_RTL8139C equ 1110100b
VER_RTL8100 equ 1111010b
VER_RTL8100B equ 1110101b
VER_RTL8139D equ VER_RTL8100B
VER_RTL8139CP equ 1110110b
VER_RTL8101 equ 1110111b
IDX_RTL8139 equ 0
IDX_RTL8139A equ 1
IDX_RTL8139B equ 2
IDX_RTL8139C equ 3
IDX_RTL8100 equ 4
IDX_RTL8139D equ 5
IDX_RTL8139D equ 6
IDX_RTL8101 equ 7
ISR_SERR equ 1 SHL 15
ISR_TIMEOUT equ 1 SHL 14
ISR_LENCHG equ 1 SHL 13
ISR_FIFOOVW equ 1 SHL 6
ISR_PUN equ 1 SHL 5
ISR_RXOVW equ 1 SHL 4
ISR_TER equ 1 SHL 3
ISR_TOK equ 1 SHL 2
ISR_RER equ 1 SHL 1
ISR_ROK equ 1 SHL 0
INTERRUPT_MASK equ ISR_ROK or \
ISR_RXOVW or \
ISR_PUN or \
ISR_FIFOOVW or \
ISR_LENCHG or \
ISR_TOK or \
ISR_TER
TSR_OWN equ 1 SHL 13
TSR_TUN equ 1 SHL 14
TSR_TOK equ 1 SHL 15
TSR_CDH equ 1 SHL 28
TSR_OWC equ 1 SHL 29
TSR_TABT equ 1 SHL 30
TSR_CRS equ 1 SHL 31
virtual at ebx
device:
ETH_DEVICE
.rx_buffer dd ?
.tx_buffer dd ?
.rx_data_offset dd ?
.io_addr dd ?
.curr_tx_desc db ?
.pci_bus db ?
.pci_dev db ?
.irq_line db ?
.hw_ver_id db ?
.TX_DESC rd NUM_TX_DESC
.size = $ - device
end virtual
section '.flat' code readable align 16
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; proc START ;;
;; ;;
;; (standard driver proc) ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
align 4
proc START stdcall, state:dword
cmp [state], 1
jne .exit
.entry:
DEBUGF 2,"Loading rtl8139 driver\n"
stdcall RegService, my_service, service_proc
ret
.fail:
.exit:
xor eax, eax
ret
endp
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; proc SERVICE_PROC ;;
;; ;;
;; (standard driver proc) ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
align 4
proc service_proc stdcall, ioctl:dword
mov edx, [ioctl]
mov eax, [IOCTL.io_code]
;------------------------------------------------------
cmp eax, 0 ;SRV_GETVERSION
jne @F
cmp [IOCTL.out_size], 4
jl .fail
mov eax, [IOCTL.output]
mov [eax], dword API_VERSION
xor eax, eax
ret
;------------------------------------------------------
@@:
cmp eax, 1 ;SRV_HOOK
jne .fail
cmp [IOCTL.inp_size], 3 ; Data input must be at least 3 bytes
jl .fail
mov eax, [IOCTL.input]
cmp byte [eax], 1 ; 1 means device number and bus number (pci) are given
jne .fail ; other types arent supported for this card yet
; check if the device is already listed
mov esi, device_list
mov ecx, [devices]
test ecx, ecx
jz .firstdevice
; mov eax, [IOCTL.input] ; get the pci bus and device numbers
mov ax , [eax+1] ;
.nextdevice:
mov ebx, [esi]
cmp ax , word [device.pci_bus] ; compare with pci and device num in device list (notice the usage of word instead of byte)
je .find_devicenum ; Device is already loaded, let's find it's device number
add esi, 4
loop .nextdevice
; This device doesnt have its own eth_device structure yet, lets create one
.firstdevice:
cmp [devices], MAX_DEVICES ; First check if the driver can handle one more card
jge .fail
allocate_and_clear ebx, device.size, .fail ; Allocate the buffer for device structure
; Fill in the direct call addresses into the struct
mov [device.reset], reset
mov [device.transmit], transmit
mov [device.get_MAC], read_mac
mov [device.set_MAC], write_mac
mov [device.unload], unload
mov [device.name], my_service
; save the pci bus and device numbers
mov eax, [IOCTL.input]
mov cl , [eax+1]
mov [device.pci_bus], cl
mov cl , [eax+2]
mov [device.pci_dev], cl
; Now, it's time to find the base io addres of the PCI device
find_io [device.pci_bus], [device.pci_dev], [device.io_addr]
; We've found the io address, find IRQ now
find_irq [device.pci_bus], [device.pci_dev], [device.irq_line]
DEBUGF 2,"Hooking into device, dev:%x, bus:%x, irq:%x, addr:%x\n",\
[device.pci_dev]:1,[device.pci_bus]:1,[device.irq_line]:1,[device.io_addr]:4
; Allocate the receive buffer
stdcall CreateRingBuffer, dword (RX_BUFFER_SIZE), dword PG_SW
test eax, eax
jz .err
mov [device.rx_buffer], eax
; Ok, the eth_device structure is ready, let's probe the device
call probe ; this function will output in eax
test eax, eax
jnz .err ; If an error occured, exit
mov eax, [devices] ; Add the device structure to our device list
mov [device_list+4*eax], ebx ; (IRQ handler uses this list to find device)
inc [devices] ;
mov [device.type], NET_TYPE_ETH
call NetRegDev
cmp eax, -1
je .destroy
ret
; If the device was already loaded, find the device number and return it in eax
.find_devicenum:
DEBUGF 2,"Trying to find device number of already registered device\n"
call NetPtrToNum ; This kernel procedure converts a pointer to device struct in ebx
; into a device number in edi
mov eax, edi ; Application wants it in eax instead
DEBUGF 2,"Kernel says: %u\n", eax
ret
; If an error occured, remove all allocated data and exit (returning -1 in eax)
.destroy:
; todo: reset device into virgin state
.err:
stdcall KernelFree, dword [device.rx_buffer]
stdcall KernelFree, ebx
.fail:
or eax, -1
ret
;------------------------------------------------------
endp
;;/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\;;
;; ;;
;; Actual Hardware dependent code starts here ;;
;; ;;
;;/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\;;
align 4
unload:
; TODO: (in this particular order)
;
; - Stop the device
; - Detach int handler
; - Remove device from local list (RTL8139_LIST)
; - call unregister function in kernel
; - Remove all allocated structures and buffers the card used
or eax,-1
ret
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;
;; probe: enables the device (if it really is RTL8139)
;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
align 4
probe:
DEBUGF 2,"Probing rtl8139 device: "
make_bus_master [device.pci_bus], [device.pci_dev]
; get chip version
set_io 0
set_io REG_TXCONFIG + 2
in ax , dx
shr ah , 2
shr ax , 6
and al , 01111111b
mov ecx, HW_VER_ARRAY_SIZE-1
.chip_ver_loop:
cmp al , [hw_ver_array + ecx]
je .chip_ver_found
dec ecx
jns .chip_ver_loop
.unknown:
mov ecx, 8
.chip_ver_found:
cmp ecx, 8
jg .unknown
mov [device.hw_ver_id], cl
mov ecx, [crosslist + ecx*4]
mov [device.name], ecx
DEBUGF 2,"Chip version: %s\n", ecx
; wake up the chip
set_io 0
set_io REG_HLTCLK
mov al , 'R' ; run the clock
out dx , al
; unlock config and BMCR registers
set_io REG_9346CR
mov al , (1 shl BIT_93C46_EEM1) or (1 shl BIT_93C46_EEM0)
out dx , al
; enable power management
set_io REG_CONFIG1
in al , dx
cmp [device.hw_ver_id], IDX_RTL8139B
jl .old_chip
; set LWAKE pin to active high (default value).
; it is for Wake-On-LAN functionality of some motherboards.
; this signal is used to inform the motherboard to execute a wake-up process.
; only at newer chips.
or al , (1 shl BIT_PMEn)
and al , not (1 shl BIT_LWACT)
out dx , al
set_io REG_CONFIG4
in al , dx
and al , not (1 shl BIT_LWPTN)
out dx , al
jmp .finish_wake_up
.old_chip:
; wake up older chips
and al , not ((1 shl BIT_SLEEP) or (1 shl BIT_PWRDWN))
out dx , al
.finish_wake_up:
; lock config and BMCR registers
xor al , al
set_io 0
set_io REG_9346CR
out dx , al
DEBUGF 2,"done!\n"
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;
;; reset: Set up all registers and descriptors, clear some values
;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
reset:
DEBUGF 2,"Resetting rtl8139: "
; attach int handler
movzx eax, [device.irq_line]
DEBUGF 1,"Attaching int handler to irq %x, ",eax:1
stdcall AttachIntHandler, eax, int_handler, dword 0
test eax, eax
jnz @f
DEBUGF 1,"\nCould not attach int handler!\n"
; or eax, -1
; ret
@@:
; reset chip
DEBUGF 1,"Resetting chip\n"
set_io 0
set_io REG_COMMAND
mov al , 1 shl BIT_RST
out dx , al
mov cx , 1000 ; wait no longer for the reset
.wait_for_reset:
in al , dx
test al , 1 shl BIT_RST
jz .reset_completed ; RST remains 1 during reset
dec cx
jns .wait_for_reset
.reset_completed:
; unlock config and BMCR registers
set_io REG_9346CR
mov al , (1 shl BIT_93C46_EEM1) or (1 shl BIT_93C46_EEM0)
out dx , al
; initialize multicast registers (no filtering)
mov eax, 0xffffffff
set_io REG_MAR0
out dx , eax
set_io REG_MAR4
out dx , eax
; enable Rx/Tx
mov al , (1 shl BIT_RE) or (1 shl BIT_TE)
set_io REG_COMMAND
out dx , al
; Rxbuffer size, unlimited dma burst, no wrapping, no rx threshold
; accept broadcast packets, accept physical match packets
mov ax , RX_CONFIG
set_io REG_RXCONFIG
out dx , ax
; 1024 bytes DMA burst, total retries = 16 + 8 * 16 = 144
mov eax , (TX_MXDMA shl BIT_TX_MXDMA) or (TXRR shl BIT_TXRR) or BIT_IFG1 or BIT_IFG0
set_io REG_TXCONFIG
out dx , eax
; enable auto negotiation
set_io REG_BMCR
in ax , dx
or ax , (1 shl BIT_ANE)
out dx , ax
; set auto negotiation advertisement
set_io REG_ANAR
in ax , dx
or ax , (1 shl BIT_SELECTOR) or (1 shl BIT_10) or (1 shl BIT_10FD) or (1 shl BIT_TX) or (1 shl BIT_TXFD)
out dx , ax
; lock config and BMCR registers
xor eax, eax
set_io REG_9346CR
out dx , al
; init RX/TX pointers
mov [device.rx_data_offset], eax
mov [device.curr_tx_desc], al
; set_io REG_CAPR
; out dx , ax
; clear packet/byte counters
lea edi, [device.bytes_tx]
mov ecx, 6
rep stosd
; clear missing packet counter
set_io REG_MPC
out dx , eax
; set RxBuffer address, init RX buffer offset
mov eax, [device.rx_buffer]
mov dword[eax], 0
DEBUGF 2,"RX buffer:%x\n", eax
GetRealAddr
DEBUGF 2,"RX buffer:%X\n", eax
set_io REG_RBSTART
out dx , eax
; Read MAC address
call read_mac
; enable interrupts
set_io 0
set_io REG_IMR
mov eax, INTERRUPT_MASK
out dx , ax
; Set the mtu, kernel will be able to send now
mov [device.mtu], 1514
; Indicate that we have successfully reset the card
DEBUGF 2,"Done!\n"
xor eax, eax
ret
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; Transmit ;;
;; ;;
;; In: buffer pointer in [esp+4] ;;
;; size of buffer in [esp+8] ;;
;; pointer to device structure in ebx ;;
;; ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
align 4
transmit:
DEBUGF 1,"\nTransmitting packet, buffer:%x, size:%u\n",[esp+4],[esp+8]
mov eax, [esp+4]
DEBUGF 1,"To: %x-%x-%x-%x-%x-%x From: %x-%x-%x-%x-%x-%x Type:%x%x\n",\
[eax+00]:2,[eax+01]:2,[eax+02]:2,[eax+03]:2,[eax+04]:2,[eax+05]:2,\
[eax+06]:2,[eax+07]:2,[eax+08]:2,[eax+09]:2,[eax+10]:2,[eax+11]:2,\
[eax+13]:2,[eax+12]:2
cmp dword [esp+8], MAX_ETH_FRAME_SIZE
jg .fail
cmp dword [esp+8], 60
jl .fail
; check if we own the current discriptor
set_io 0
set_io REG_TSD0
movzx ecx, [device.curr_tx_desc]
shl ecx, 2
add edx, ecx
in eax, dx
test eax, (1 shl BIT_OWN)
jz .wait_to_send
.send_packet:
; get next descriptor
inc [device.curr_tx_desc]
and [device.curr_tx_desc], NUM_TX_DESC-1
; Update stats
inc [device.packets_tx]
mov eax, [esp+8]
add dword [device.bytes_tx], eax
adc dword [device.bytes_tx + 4], 0
; Set the buffer address
set_io REG_TSAD0
mov eax, [esp+4]
mov [device.TX_DESC+ecx], eax
GetRealAddr
out dx, eax
; And the size of the buffer
set_io REG_TSD0
mov eax, [esp+8]
or eax, (ERTXTH shl BIT_ERTXTH) ; Early threshold
out dx, eax
DEBUGF 1,"Packet Sent!\n"
xor eax, eax
ret 8
.wait_to_send:
DEBUGF 1,"Waiting for timeout\n"
push edx
mov esi, 300
stdcall Sleep
pop edx
in ax, dx
test ax, (1 shl BIT_OWN)
jnz .send_packet
pusha
call reset ; if chip hung, reset it
popa
jmp .send_packet
.fail:
DEBUGF 1,"failed!\n"
stdcall KernelFree, [esp+4]
or eax, -1
ret 8
;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; Interrupt handler ;;
;; ;;
;;;;;;;;;;;;;;;;;;;;;;;
align 4
int_handler:
DEBUGF 1,"\nIRQ %x\n", eax:2 ; no, you cant replace 'eax:2' with 'al', this must be a bug in FDO
; find pointer of device wich made IRQ occur
mov esi, device_list
mov ecx, [devices]
test ecx, ecx
jz .fail
.nextdevice:
mov ebx, dword [esi]
set_io 0
set_io REG_ISR
in ax , dx
out dx , ax ; send it back to ACK
add esi, 4
test ax , ax
jnz .got_it
dec ecx
jnz .nextdevice
ret ; If no device was found, abort (The irq was probably for a device, not registered to this driver)
.got_it:
; looks like we've found it!
; Lets found out why the irq occured then..
;----------------------------------------------------
; Received packet ok?
test ax, ISR_ROK
jz @f
push ax
.receive:
set_io 0
set_io REG_COMMAND
in al , dx
test al , BUFE ; test if RX buffer is empty
jnz .finish ;
DEBUGF 1,"RX: "
mov eax, [device.rx_buffer]
add eax, [device.rx_data_offset]
test byte [eax], (1 shl BIT_ROK) ; check if packet is ok
jz .reset_rx
; packet is ok, copy it
movzx ecx, word [eax+2] ; packet length
sub ecx, 4 ; don't copy CRC
; Update stats
add dword [device.bytes_rx], ecx
adc dword [device.bytes_rx + 4], 0
inc dword [device.packets_rx]
DEBUGF 1,"Received %u bytes\n", ecx
push ebx eax ecx
stdcall KernelAlloc, ecx ; Allocate a buffer to put packet into
pop ecx
test eax, eax ; Test if we allocated succesfully
jz .abort
mov edi, eax ; Where we will copy too
mov esi, [esp] ; The buffer we will copy from
add esi, 4 ; Dont copy CRC
push dword .abort ; Kernel will return to this address after EthReceiver
push ecx edi ; Save buffer pointer and size, to pass to kernel
.copy:
shr ecx, 1
jnc .nb
movsb
.nb:
shr ecx, 1
jnc .nw
movsw
.nw:
jz .nd
rep movsd
.nd:
jmp EthReceiver ; Send it to kernel
.abort:
pop eax ebx
; update eth_data_start_offset
movzx eax, word [eax+2] ; packet length
add eax, [device.rx_data_offset]
add eax, 4+3 ; packet header is 4 bytes long + dword alignment
and eax, not 3 ; dword alignment
cmp eax, RX_BUFFER_SIZE
jl .no_wrap
DEBUGF 2,"Wrapping"
sub eax, RX_BUFFER_SIZE
.no_wrap:
mov [device.rx_data_offset], eax
DEBUGF 1,"New RX ptr: %d\n", eax
set_io 0
set_io REG_CAPR ; update 'Current Address of Packet Read register'
sub eax, 0x10 ; value 0x10 is a constant for CAPR
out dx , ax
jmp .receive ; check for multiple packets
.reset_rx:
test byte [eax], (1 shl BIT_CRC)
jz .no_crc_error
DEBUGF 2,"\nCRC error!\n"
.no_crc_error:
test byte [eax], (1 shl BIT_FAE)
jz .no_fae_error
DEBUGF 1,"\nFrame alignment error!\n"
.no_fae_error:
DEBUGF 1,"Reset RX\n"
in al , dx ; read command register
push ax
and al , not (1 shl BIT_RE) ; Clear the RE bit
out dx , al
pop ax
out dx , al ; write original command back
add edx, REG_RXCONFIG - REG_COMMAND ; Restore RX configuration
mov ax , RX_CONFIG
out dx , ax
.finish:
pop ax
;----------------------------------------------------
; Transmit ok / Transmit error
@@:
test ax, ISR_TOK + ISR_TER
jz @f
push ax
xor ecx, ecx
.txdesloop:
set_io 0
set_io REG_TSD0
add edx, ecx
in eax, dx
test eax, TSR_OWN ; DMA operation completed
jz .notthisone
cmp [device.TX_DESC+ecx], 0
je .notthisone
; .notxd:
; test eax, TSR_TUN
; jz .nobun
; DEBUGF 2, "TX: FIFO Buffer underrun!\n"
;
; .nobun:
; test eax, TSR_OWC
; jz .noowc
; DEBUGF 2, "TX: OWC!\n"
;
; .noowc:
; test eax, TSR_TABT
; jz .notabt
; DEBUGF 2, "TX: TABT!\n"
;
; .notabt:
; test eax, TSR_CRS
; jz .nocsl
; DEBUGF 2, "TX: Carrier Sense Lost!\n"
;
; .nocsl:
DEBUGF 1,"TX OK: free buffer %x\n", [device.TX_DESC+ecx]:8
push ecx ebx
stdcall KernelFree, [device.TX_DESC+ecx]
pop ebx ecx
mov [device.TX_DESC+ecx], 0
.notthisone:
add ecx, 4
cmp ecx, 16
jl .txdesloop
pop ax
;----------------------------------------------------
; Rx buffer overflow ?
@@:
test ax, ISR_RXOVW
jz @f
push ax
DEBUGF 2,"RX-buffer overflow!\n"
set_io 0
set_io REG_ISR
mov ax , ISR_FIFOOVW or ISR_RXOVW
out dx , ax
pop ax
;----------------------------------------------------
; Packet underrun?
@@:
test ax, ISR_PUN
jz @f
DEBUGF 2,"Packet underrun!\n"
;----------------------------------------------------
; Receive FIFO overflow ?
@@:
test ax, ISR_FIFOOVW
jz @f
push ax
DEBUGF 2,"RX fifo overflow!\n"
set_io 0
set_io REG_ISR
mov ax , ISR_FIFOOVW or ISR_RXOVW
out dx , ax
pop ax
;----------------------------------------------------
; Something about Cable changed ?
@@:
test ax, ISR_LENCHG
jz .fail
DEBUGF 2,"Cable changed!\n"
call cable
.fail:
ret
;;;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; Update Cable status ;;
;; ;;
;;;;;;;;;;;;;;;;;;;;;;;;;
align 4
cable:
DEBUGF 1,"Checking Cable status: "
mov edx, dword [device.io_addr]
add edx, REG_MSR
in al , dx
; test al , 1 SHL 2 ; 0 = link ok 1 = link fail
; jnz .notconnected
; test al , 1 SHL 3 ; 0 = 100 Mbps 1 = 10 Mbps
; jnz .10mbps
shr al, 2
and al, 3
mov byte [device.mode+3], al
DEBUGF 1,"Done!\n"
ret
;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; Write MAC address ;;
;; ;;
;;;;;;;;;;;;;;;;;;;;;;;
align 4
write_mac: ; in: mac pushed onto stack (as 3 words)
DEBUGF 2,"Writing MAC: "
; disable all in command registers
set_io 0
set_io REG_9346CR
xor eax, eax
out dx , al
set_io REG_IMR
xor eax, eax
out dx , ax
set_io REG_ISR
mov eax, -1
out dx , ax
; enable writing
set_io REG_9346CR
mov eax, REG_9346CR_WE
out dx , al
; write the mac ...
set_io REG_IDR0
pop eax
out dx , eax
set_io REG_IDR0+4
xor eax, eax
pop ax
out dx , eax
; disable writing
set_io REG_9346CR
xor eax, eax
out dx , al
DEBUGF 2,"ok!\n"
; Notice this procedure does not ret, but continues to read_mac instead.
;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; Read MAC address ;;
;; ;;
;;;;;;;;;;;;;;;;;;;;;;
read_mac:
DEBUGF 2,"Reading MAC: "
set_io 0
lea edi, [device.mac]
in eax, dx
stosd
add edx, 4
in ax, dx
stosw
DEBUGF 2,"%x-%x-%x-%x-%x-%x\n",[edi-6]:2,[edi-5]:2,[edi-4]:2,[edi-3]:2,[edi-2]:2,[edi-1]:2
ret
; End of code
section '.data' data readable writable align 16 ; place all uninitialized data place here
align 4 ; Place all initialised data here
devices dd 0
version dd (DRIVER_VERSION shl 16) or (API_VERSION and 0xFFFF)
my_service db 'RTL8139',0 ; max 16 chars include zero
device_1 db 'Realtek 8139',0
device_2 db 'Realtek 8139A',0
device_3 db 'Realtek 8139B',0
device_4 db 'Realtek 8139C',0
device_5 db 'Realtek 8100',0
device_6 db 'Realtek 8139D',0
device_7 db 'Realtek 8139CP',0
device_8 db 'Realtek 8101',0
device_unknown db 'Unknown RTL8139 clone', 0
crosslist:
dd device_1
dd device_2
dd device_3
dd device_4
dd device_5
dd device_6
dd device_7
dd device_8
dd device_unknown
hw_ver_array: ; This array is used by the probe routine to find out wich version of the RTL8139 we are working with
db VER_RTL8139
db VER_RTL8139A
db VER_RTL8139B
db VER_RTL8139C
db VER_RTL8100
db VER_RTL8139D
db VER_RTL8139CP
db VER_RTL8101
db 0
HW_VER_ARRAY_SIZE = $-hw_ver_array
include_debug_strings ; All data wich FDO uses will be included here
device_list rd MAX_DEVICES ; This list contains all pointers to device structures the driver is handling