WebSVN – Kolibri OS – Diff – /drivers/ethernet/i8254x.asm


;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;                                                                 ;;
;; Copyright (C) KolibriOS team 2004-2014. All rights reserved.    ;;
;; Distributed under terms of the GNU General Public License       ;;
;;                                                                 ;;
;;  i8254x driver for KolibriOS                                    ;;
;;                                                                 ;;
;;  based on i8254x.asm from baremetal os                          ;;
;;                                                                 ;;
;;    Written by hidnplayr (hidnplayr@gmail.com)                   ;;
;;                                                                 ;;
;;          GNU GENERAL PUBLIC LICENSE                             ;;
;;             Version 2, June 1991                                ;;
;;                                                                 ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
 
format PE DLL native
entry START
 
        CURRENT_API             = 0x0200
        COMPATIBLE_API          = 0x0100
        API_VERSION             = (COMPATIBLE_API shl 16) + CURRENT_API
 
        MAX_DEVICES             = 16
 
        __DEBUG__               = 1
        __DEBUG_LEVEL__         = 2             ; 1 = verbose, 2 = errors only
 
        MAX_PKT_SIZE            = 4096          ; Maximum packet size
 
        RX_RING_SIZE            = 8             ; Must be a power of 2, and minimum 8
        TX_RING_SIZE            = 8             ; Must be a power of 2, and minimum 8
 
section '.flat' readable writable executable
 
include '../proc32.inc'
include '../struct.inc'
include '../macros.inc'
include '../fdo.inc'
include '../netdrv.inc'
 
; Register list
REG_CTRL                = 0x0000 ; Control Register
REG_STATUS              = 0x0008 ; Device Status Register
REG_CTRLEXT             = 0x0018 ; Extended Control Register
REG_MDIC                = 0x0020 ; MDI Control Register
REG_FCAL                = 0x0028 ; Flow Control Address Low
REG_FCAH                = 0x002C ; Flow Control Address High
REG_FCT                 = 0x0030 ; Flow Control Type
REG_VET                 = 0x0038 ; VLAN Ether Type
REG_ICR                 = 0x00C0 ; Interrupt Cause Read
REG_ITR                 = 0x00C4 ; Interrupt Throttling Register
REG_ICS                 = 0x00C8 ; Interrupt Cause Set Register
REG_IMS                 = 0x00D0 ; Interrupt Mask Set/Read Register
REG_IMC                 = 0x00D8 ; Interrupt Mask Clear Register
REG_RCTL                = 0x0100 ; Receive Control Register
REG_FCTTV               = 0x0170 ; Flow Control Transmit Timer Value
REG_TXCW                = 0x0178 ; Transmit Configuration Word
REG_RXCW                = 0x0180 ; Receive Configuration Word
REG_TCTL                = 0x0400 ; Transmit Control Register
REG_TIPG                = 0x0410 ; Transmit Inter Packet Gap
 
REG_LEDCTL              = 0x0E00 ; LED Control
REG_PBA                 = 0x1000 ; Packet Buffer Allocation
 
REG_RDBAL               = 0x2800 ; RX Descriptor Base Address Low
REG_RDBAH               = 0x2804 ; RX Descriptor Base Address High
REG_RDLEN               = 0x2808 ; RX Descriptor Length
REG_RDH                 = 0x2810 ; RX Descriptor Head
REG_RDT                 = 0x2818 ; RX Descriptor Tail
REG_RDTR                = 0x2820 ; RX Delay Timer Register
REG_RXDCTL              = 0x3828 ; RX Descriptor Control
REG_RADV                = 0x282C ; RX Int. Absolute Delay Timer
REG_RSRPD               = 0x2C00 ; RX Small Packet Detect Interrupt
 
REG_TXDMAC              = 0x3000 ; TX DMA Control
REG_TDBAL               = 0x3800 ; TX Descriptor Base Address Low
REG_TDBAH               = 0x3804 ; TX Descriptor Base Address High
REG_TDLEN               = 0x3808 ; TX Descriptor Length
REG_TDH                 = 0x3810 ; TX Descriptor Head
REG_TDT                 = 0x3818 ; TX Descriptor Tail
REG_TIDV                = 0x3820 ; TX Interrupt Delay Value
REG_TXDCTL              = 0x3828 ; TX Descriptor Control
REG_TADV                = 0x382C ; TX Absolute Interrupt Delay Value
REG_TSPMT               = 0x3830 ; TCP Segmentation Pad & Min Threshold
 
REG_RXCSUM              = 0x5000 ; RX Checksum Control
 
; Register list for i8254x
I82542_REG_RDTR         = 0x0108 ; RX Delay Timer Register
I82542_REG_RDBAL        = 0x0110 ; RX Descriptor Base Address Low
I82542_REG_RDBAH        = 0x0114 ; RX Descriptor Base Address High
I82542_REG_RDLEN        = 0x0118 ; RX Descriptor Length
I82542_REG_RDH          = 0x0120 ; RDH for i82542
I82542_REG_RDT          = 0x0128 ; RDT for i82542
I82542_REG_TDBAL        = 0x0420 ; TX Descriptor Base Address Low
I82542_REG_TDBAH        = 0x0424 ; TX Descriptor Base Address Low
I82542_REG_TDLEN        = 0x0428 ; TX Descriptor Length
I82542_REG_TDH          = 0x0430 ; TDH for i82542
I82542_REG_TDT          = 0x0438 ; TDT for i82542
 
; CTRL - Control Register (0x0000)
CTRL_FD                 = 0x00000001 ; Full Duplex
CTRL_LRST               = 0x00000008 ; Link Reset
CTRL_ASDE               = 0x00000020 ; Auto-speed detection
CTRL_SLU                = 0x00000040 ; Set Link Up
CTRL_ILOS               = 0x00000080 ; Invert Loss of Signal
CTRL_SPEED_MASK         = 0x00000300 ; Speed selection
CTRL_SPEED_SHIFT        = 8
CTRL_FRCSPD             = 0x00000800 ; Force Speed
CTRL_FRCDPLX            = 0x00001000 ; Force Duplex
CTRL_SDP0_DATA          = 0x00040000 ; SDP0 data
CTRL_SDP1_DATA          = 0x00080000 ; SDP1 data
CTRL_SDP0_IODIR         = 0x00400000 ; SDP0 direction
CTRL_SDP1_IODIR         = 0x00800000 ; SDP1 direction
CTRL_RST                = 0x04000000 ; Device Reset
CTRL_RFCE               = 0x08000000 ; RX Flow Ctrl Enable
CTRL_TFCE               = 0x10000000 ; TX Flow Ctrl Enable
CTRL_VME                = 0x40000000 ; VLAN Mode Enable
CTRL_PHY_RST            = 0x80000000 ; PHY reset
 
; STATUS - Device Status Register (0x0008)
STATUS_FD               = 0x00000001 ; Full Duplex
STATUS_LU               = 0x00000002 ; Link Up
STATUS_TXOFF            = 0x00000010 ; Transmit paused
STATUS_TBIMODE          = 0x00000020 ; TBI Mode
STATUS_SPEED_MASK       = 0x000000C0 ; Link Speed setting
STATUS_SPEED_SHIFT      = 6
STATUS_ASDV_MASK        = 0x00000300 ; Auto Speed Detection
STATUS_ASDV_SHIFT       = 8
STATUS_PCI66            = 0x00000800 ; PCI bus speed
STATUS_BUS64            = 0x00001000 ; PCI bus width
STATUS_PCIX_MODE        = 0x00002000 ; PCI-X mode
STATUS_PCIXSPD_MASK     = 0x0000C000 ; PCI-X speed
STATUS_PCIXSPD_SHIFT    = 14
 
; CTRL_EXT - Extended Device Control Register (0x0018)
CTRLEXT_PHY_INT         = 0x00000020 ; PHY interrupt
CTRLEXT_SDP6_DATA       = 0x00000040 ; SDP6 data
CTRLEXT_SDP7_DATA       = 0x00000080 ; SDP7 data
CTRLEXT_SDP6_IODIR      = 0x00000400 ; SDP6 direction
CTRLEXT_SDP7_IODIR      = 0x00000800 ; SDP7 direction
CTRLEXT_ASDCHK          = 0x00001000 ; Auto-Speed Detect Chk
CTRLEXT_EE_RST          = 0x00002000 ; EEPROM reset
CTRLEXT_SPD_BYPS        = 0x00008000 ; Speed Select Bypass
CTRLEXT_RO_DIS          = 0x00020000 ; Relaxed Ordering Dis.
CTRLEXT_LNKMOD_MASK     = 0x00C00000 ; Link Mode
CTRLEXT_LNKMOD_SHIFT    = 22
 
; MDIC - MDI Control Register (0x0020)
MDIC_DATA_MASK          = 0x0000FFFF ; Data
MDIC_REG_MASK           = 0x001F0000 ; PHY Register
MDIC_REG_SHIFT          = 16
MDIC_PHY_MASK           = 0x03E00000 ; PHY Address
MDIC_PHY_SHIFT          = 21
MDIC_OP_MASK            = 0x0C000000 ; Opcode
MDIC_OP_SHIFT           = 26
MDIC_R                  = 0x10000000 ; Ready
MDIC_I                  = 0x20000000 ; Interrupt Enable
MDIC_E                  = 0x40000000 ; Error
 
; ICR - Interrupt Cause Read (0x00c0)
ICR_TXDW                = 0x00000001 ; TX Desc Written back
ICR_TXQE                = 0x00000002 ; TX Queue Empty
ICR_LSC                 = 0x00000004 ; Link Status Change
ICR_RXSEQ               = 0x00000008 ; RX Sence Error
ICR_RXDMT0              = 0x00000010 ; RX Desc min threshold reached
ICR_RXO                 = 0x00000040 ; RX Overrun
ICR_RXT0                = 0x00000080 ; RX Timer Interrupt
ICR_MDAC                = 0x00000200 ; MDIO Access Complete
ICR_RXCFG               = 0x00000400
ICR_PHY_INT             = 0x00001000 ; PHY Interrupt
ICR_GPI_SDP6            = 0x00002000 ; GPI on SDP6
ICR_GPI_SDP7            = 0x00004000 ; GPI on SDP7
ICR_TXD_LOW             = 0x00008000 ; TX Desc low threshold hit
ICR_SRPD                = 0x00010000 ; Small RX packet detected
 
; RCTL - Receive Control Register (0x0100)
RCTL_EN                 = 0x00000002 ; Receiver Enable
RCTL_SBP                = 0x00000004 ; Store Bad Packets
RCTL_UPE                = 0x00000008 ; Unicast Promiscuous Enabled
RCTL_MPE                = 0x00000010 ; Xcast Promiscuous Enabled
RCTL_LPE                = 0x00000020 ; Long Packet Reception Enable
RCTL_LBM_MASK           = 0x000000C0 ; Loopback Mode
RCTL_LBM_SHIFT          = 6
RCTL_RDMTS_MASK         = 0x00000300 ; RX Desc Min Threshold Size
RCTL_RDMTS_SHIFT        = 8
RCTL_MO_MASK            = 0x00003000 ; Multicast Offset
RCTL_MO_SHIFT           = 12
RCTL_BAM                = 0x00008000 ; Broadcast Accept Mode
RCTL_BSIZE_MASK         = 0x00030000 ; RX Buffer Size
RCTL_BSIZE_SHIFT        = 16
RCTL_VFE                = 0x00040000 ; VLAN Filter Enable
RCTL_CFIEN              = 0x00080000 ; CFI Enable
RCTL_CFI                = 0x00100000 ; Canonical Form Indicator Bit
RCTL_DPF                = 0x00400000 ; Discard Pause Frames
RCTL_PMCF               = 0x00800000 ; Pass MAC Control Frames
RCTL_BSEX               = 0x02000000 ; Buffer Size Extension
RCTL_SECRC              = 0x04000000 ; Strip Ethernet CRC
 
; TCTL - Transmit Control Register (0x0400)
TCTL_EN                 = 0x00000002 ; Transmit Enable
TCTL_PSP                = 0x00000008 ; Pad short packets
TCTL_SWXOFF             = 0x00400000 ; Software XOFF Transmission
 
; PBA - Packet Buffer Allocation (0x1000)
PBA_RXA_MASK            = 0x0000FFFF ; RX Packet Buffer
PBA_RXA_SHIFT           = 0
PBA_TXA_MASK            = 0xFFFF0000 ; TX Packet Buffer
PBA_TXA_SHIFT           = 16
 
; Flow Control Type
FCT_TYPE_DEFAULT        = 0x8808
 
 
 
; === TX Descriptor ===
 
struct TDESC
        addr_l          dd ?
        addr_h          dd ?
        length_cso_cmd  dd ?    ; 16 bits length + 8 bits cso + 8 bits cmd
        status          dd ?    ; status, checksum start field, special
ends
 
; TX Packet Length (word 2)
TXDESC_LEN_MASK         = 0x0000ffff
 
; TX Descriptor CMD field (word 2)
TXDESC_IDE              = 0x80000000 ; Interrupt Delay Enable
TXDESC_VLE              = 0x40000000 ; VLAN Packet Enable
TXDESC_DEXT             = 0x20000000 ; Extension
TXDESC_RPS              = 0x10000000 ; Report Packet Sent
TXDESC_RS               = 0x08000000 ; Report Status
TXDESC_IC               = 0x04000000 ; Insert Checksum
TXDESC_IFCS             = 0x02000000 ; Insert FCS
TXDESC_EOP              = 0x01000000 ; End Of Packet
 
; TX Descriptor STA field (word 3)
TXDESC_TU               = 0x00000008 ; Transmit Underrun
TXDESC_LC               = 0x00000004 ; Late Collision
TXDESC_EC               = 0x00000002 ; Excess Collisions
TXDESC_DD               = 0x00000001 ; Descriptor Done
 
 
 
; === RX Descriptor ===
 
struct RDESC
        addr_l          dd ?
        addr_h          dd ?
        status_l        dd ?
        status_h        dd ?
ends
 
; RX Packet Length (word 2)
RXDESC_LEN_MASK         = 0x0000ffff
 
; RX Descriptor STA field (word 3)
RXDESC_PIF              = 0x00000080 ; Passed In-exact Filter
RXDESC_IPCS             = 0x00000040 ; IP cksum calculated
RXDESC_TCPCS            = 0x00000020 ; TCP cksum calculated
RXDESC_VP               = 0x00000008 ; Packet is 802.1Q
RXDESC_IXSM             = 0x00000004 ; Ignore cksum indication
RXDESC_EOP              = 0x00000002 ; End Of Packet
RXDESC_DD               = 0x00000001 ; Descriptor Done
 
struct  device          ETH_DEVICE
 
        mmio_addr       dd ?
        pci_bus         dd ?
        pci_dev         dd ?
        irq_line        db ?
 
        cur_rx          dd ?
        cur_tx          dd ?
        last_tx         dd ?
 
        rb 0x100 - ($ and 0xff) ; align 256
 
        rx_desc         rb RX_RING_SIZE*sizeof.RDESC*2
 
        rb 0x100 - ($ and 0xff) ; align 256
 
        tx_desc         rb TX_RING_SIZE*sizeof.TDESC*2
 
ends
 
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;                        ;;
;; proc START             ;;
;;                        ;;
;; (standard driver proc) ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
 
proc START c, reason:dword, cmdline:dword
 
        cmp     [reason], DRV_ENTRY
        jne     .fail
 
        DEBUGF  1,"Loading driver\n"
        invoke  RegService, my_service, service_proc
        ret
 
  .fail:
        xor     eax, eax
        ret
 
endp
 
 
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;                        ;;
;; proc SERVICE_PROC      ;;
;;                        ;;
;; (standard driver proc) ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
 
align 4
proc service_proc stdcall, ioctl:dword
 
        mov     edx, [ioctl]
        mov     eax, [edx + IOCTL.io_code]
 
;------------------------------------------------------
 
        cmp     eax, 0 ;SRV_GETVERSION
        jne     @F
 
        cmp     [edx + IOCTL.out_size], 4
        jb      .fail
        mov     eax, [edx + IOCTL.output]
        mov     dword[eax], API_VERSION
 
        xor     eax, eax
        ret
 
;------------------------------------------------------
  @@:
        cmp     eax, 1 ;SRV_HOOK
        jne     .fail
 
        cmp     [edx + IOCTL.inp_size], 3               ; Data input must be at least 3 bytes
        jb      .fail
 
        mov     eax, [edx + IOCTL.input]
        cmp     byte[eax], 1                            ; 1 means device number and bus number (pci) are given
        jne     .fail                                   ; other types arent supported for this card yet
 
; check if the device is already listed
 
        mov     esi, device_list
        mov     ecx, [devices]
        test    ecx, ecx
        jz      .firstdevice
 
;        mov     eax, [edx + IOCTL.input]                ; get the pci bus and device numbers
        mov     ax, [eax+1]                             ;
  .nextdevice:
        mov     ebx, [esi]
        cmp     al, byte[ebx + device.pci_bus]
        jne     .next
        cmp     ah, byte[ebx + device.pci_dev]
        je      .find_devicenum                         ; Device is already loaded, let's find it's device number
  .next:
        add     esi, 4
        loop    .nextdevice
 
 
; This device doesnt have its own eth_device structure yet, lets create one
  .firstdevice:
        cmp     [devices], MAX_DEVICES                  ; First check if the driver can handle one more card
        jae     .fail
 
        allocate_and_clear ebx, sizeof.device, .fail    ; Allocate the buffer for device structure
 
; Fill in the direct call addresses into the struct
 
        mov     [ebx + device.reset], reset
        mov     [ebx + device.transmit], transmit
        mov     [ebx + device.unload], unload
        mov     [ebx + device.name], my_service
 
; save the pci bus and device numbers
 
        mov     eax, [edx + IOCTL.input]
        movzx   ecx, byte[eax+1]
        mov     [ebx + device.pci_bus], ecx
        movzx   ecx, byte[eax+2]
        mov     [ebx + device.pci_dev], ecx
 
; Now, it's time to find the base mmio addres of the PCI device
 
        stdcall PCI_find_mmio32, [ebx + device.pci_bus], [ebx + device.pci_dev] ; returns in eax
 
; Create virtual mapping of the physical memory
 
        invoke  MapIoMem, eax, 10000h, PG_SW+PG_NOCACHE
        mov     [ebx + device.mmio_addr], eax
 
; We've found the mmio address, find IRQ now
 
        invoke  PciRead8, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.interrupt_line
        mov     [ebx + device.irq_line], al
 
        DEBUGF  1,"Hooking into device, dev:%x, bus:%x, irq:%x, addr:%x\n",\
        [ebx + device.pci_dev]:1,[ebx + device.pci_bus]:1,[ebx + device.irq_line]:1,[ebx + device.mmio_addr]:8
 
; Ok, the eth_device structure is ready, let's probe the device
        call    probe                                   ; this function will output in eax
        test    eax, eax
        jnz     .err                                    ; If an error occured, exit
 
        mov     eax, [devices]                          ; Add the device structure to our device list
        mov     [device_list+4*eax], ebx                ; (IRQ handler uses this list to find device)
        inc     [devices]                               ;
 
        call    start_i8254x
        test    eax, eax
        jnz     .destroy
 
        mov     [ebx + device.type], NET_TYPE_ETH
        invoke  NetRegDev
        cmp     eax, -1
        je      .destroy
 
        ret
 
; If the device was already loaded, find the device number and return it in eax
 
  .find_devicenum:
        DEBUGF  1,"Trying to find device number of already registered device\n"
        invoke  NetPtrToNum                             ; This kernel procedure converts a pointer to device struct in ebx
                                                        ; into a device number in edi
        mov     eax, edi                                ; Application wants it in eax instead
        DEBUGF  1,"Kernel says: %u\n", eax
        ret
 
; If an error occured, remove all allocated data and exit (returning -1 in eax)
 
  .destroy:
        ; todo: reset device into virgin state
 
  .err:
        invoke  KernelFree, ebx
 
  .fail:
        DEBUGF  2,"Loading driver failed\n"
        or      eax, -1
        ret
 
;------------------------------------------------------
endp
 
 
;;/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\;;
;;                                                                        ;;
;;        Actual Hardware dependent code starts here                      ;;
;;                                                                        ;;
;;/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\;;
 
 
align 4
unload:
 
        DEBUGF  1,"Unload\n"
 
        ; TODO: (in this particular order)
        ;
        ; - Stop the device
        ; - Detach int handler
        ; - Remove device from local list (device_list)
        ; - call unregister function in kernel
        ; - Remove all allocated structures and buffers the card used
 
        or      eax, -1
 
        ret
 
 
 
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;
;;  probe: enables the device (if it really is I8254X)
;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
align 4
probe:
 
        DEBUGF  1,"Probe\n"
 
; Make the device a bus master
        invoke  PciRead32, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.command
        or      al, PCI_CMD_MASTER
        invoke  PciWrite32, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.command, eax
 
        ; TODO: validate the device
 
        call    read_mac
 
        movzx   eax, [ebx + device.irq_line]
        DEBUGF  1,"Attaching int handler to irq %x\n", eax:1
        invoke  AttachIntHandler, eax, int_handler, ebx
        test    eax, eax
        jnz     @f
        DEBUGF  2,"Could not attach int handler!\n"
        or      eax, -1
        ret
  @@:
 
 
reset_dontstart:
        DEBUGF  1,"Reset\n"
 
        mov     esi, [ebx + device.mmio_addr]
 
        or      dword[esi + REG_CTRL], CTRL_RST         ; reset device
  .loop:
        push    esi
        xor     esi, esi
        inc     esi
        invoke  Sleep
        pop     esi
        test    dword[esi + REG_CTRL], CTRL_RST
        jnz     .loop
 
        mov     dword[esi + REG_IMC], 0xffffffff        ; Disable all interrupt causes
        mov     eax, dword [esi + REG_ICR]              ; Clear any pending interrupts
        mov     dword[esi + REG_ITR], 0                 ; Disable interrupt throttling logic
 
        mov     dword[esi + REG_PBA], 0x00000004        ; PBA: set the RX buffer size to 4KB (TX buffer is calculated as 64-RX buffer)
        mov     dword[esi + REG_RDTR], 0                ; RDTR: set no delay
 
        mov     dword[esi + REG_TXCW], 0x80008060       ; TXCW: set ANE, TxConfigWord (Half/Full duplex, Next Page Reqest)
 
        mov     eax, [esi + REG_CTRL]
        or      eax, 1 shl 6 + 1 shl 5
        and     eax, not (1 shl 3 + 1 shl 7 + 1 shl 30 + 1 shl 31)
        mov     dword [esi + REG_CTRL], eax             ; CTRL: clear LRST, set SLU and ASDE, clear RSTPHY, VME, and ILOS
 
        lea     edi, [esi + 0x5200]                     ; MTA: reset
        mov     eax, 0xffffffff
        stosd
        stosd
        stosd
        stosd
 
        call    init_rx
        test    eax, eax
        jnz     .fail
        call    init_tx
 
        xor     eax, eax
  .fail:
        ret
 
 
 
align 4
init_rx:
 
        lea     edi, [ebx + device.rx_desc]
        mov     ecx, RX_RING_SIZE
  .loop:
 
        push    ecx edi
        invoke  KernelAlloc, MAX_PKT_SIZE
        test    eax, eax
        jz      .out_of_mem
        DEBUGF  1,"RX buffer: 0x%x\n", eax
        pop     edi
        mov     dword[edi + RX_RING_SIZE*sizeof.RDESC], eax
        push    edi
        invoke  GetPhysAddr
        pop     edi
        mov     [edi + RDESC.addr_l], eax
        mov     [edi + RDESC.addr_h], 0
        mov     [edi + RDESC.status_l], 0
        mov     [edi + RDESC.status_h], 0
        add     edi, sizeof.RDESC
        pop     ecx
        dec     ecx
        jnz     .loop
 
        mov     [ebx + device.cur_rx], 0
 
        lea     eax, [ebx + device.rx_desc]
        invoke  GetPhysAddr
        mov     dword[esi + REG_RDBAL], eax                             ; Receive Descriptor Base Address Low
        mov     dword[esi + REG_RDBAH], 0                               ; Receive Descriptor Base Address High
        mov     dword[esi + REG_RDLEN], RX_RING_SIZE*sizeof.RDESC       ; Receive Descriptor Length
        mov     dword[esi + REG_RDH], 0                                 ; Receive Descriptor Head
        mov     dword[esi + REG_RDT], RX_RING_SIZE-1                    ; Receive Descriptor Tail
        mov     dword[esi + REG_RCTL], RCTL_SBP or RCTL_BAM or RCTL_SECRC or RCTL_UPE or RCTL_MPE
        ; Store Bad Packets, Broadcast Accept Mode, Strip Ethernet CRC from incoming packet, Promiscuous mode
        xor     eax, eax        ; success!
        ret
 
  .out_of_mem:
        DEBUGF  2,"Out of memory!\n"
        pop     edi ecx
        or      eax, -1         ; error!
        ret
 
 
 
align 4
init_tx:
 
        lea     edi, [ebx + device.tx_desc]
        mov     ecx, TX_RING_SIZE
  .loop:
        mov     [edi + TDESC.addr_l], eax
        mov     [edi + TDESC.addr_h], 0
        mov     [edi + TDESC.length_cso_cmd], 0
        mov     [edi + TDESC.status], 0
        add     edi, sizeof.TDESC
        dec     ecx
        jnz     .loop
 
        mov     [ebx + device.cur_tx], 0
        mov     [ebx + device.last_tx], 0
 
        lea     eax, [ebx + device.tx_desc]
        invoke  GetPhysAddr
        mov     dword[esi + REG_TDBAL], eax                             ; Transmit Descriptor Base Address Low
        mov     dword[esi + REG_TDBAH], 0                               ; Transmit Descriptor Base Address High
        mov     dword[esi + REG_TDLEN], RX_RING_SIZE*sizeof.TDESC       ; Transmit Descriptor Length
        mov     dword[esi + REG_TDH], 0                                 ; Transmit Descriptor Head
        mov     dword[esi + REG_TDT], 0                                 ; Transmit Descriptor Tail
        mov     dword[esi + REG_TCTL], 0x010400fa                       ; Enabled, Pad Short Packets, 15 retrys, 64-byte COLD, Re-transmit on Late Collision
        mov     dword[esi + REG_TIPG], 0x0060200A                       ; IPGT 10, IPGR1 8, IPGR2 6
 
        ret
 
 
align 4
reset:
        call    reset_dontstart
        test    eax, eax
        je      start_i8254x
 
        ret
 
align 4
start_i8254x:
 
        mov     esi, [ebx + device.mmio_addr]
        or      dword[esi + REG_RCTL], RCTL_EN          ; Enable the receiver
 
        xor     eax, eax
        mov     [esi + REG_RDTR], eax                   ; Clear the Receive Delay Timer Register
        mov     [esi + REG_RADV], eax                   ; Clear the Receive Interrupt Absolute Delay Timer
        mov     [esi + REG_RSRPD], eax                  ; Clear the Receive Small Packet Detect Interrupt
 
        mov     dword[esi + REG_IMS], 0x1F6DC           ; Enable interrupt types
        mov     eax, [esi + REG_ICR]                    ; Clear pending interrupts
 
        mov     [ebx + device.mtu], 1514
        mov     [ebx + device.state], ETH_LINK_UNKNOWN  ; Set link state to unknown
 
        xor     eax, eax
        ret
 
 
 
 
align 4
read_mac:
 
        DEBUGF  1,"Read MAC\n"
 
        mov     esi, [ebx + device.mmio_addr]
 
        mov     eax, [esi+0x5400]                       ; RAL
        test    eax, eax
        jz      .try_eeprom
 
        mov     dword[ebx + device.mac], eax
        mov     eax, [esi+0x5404]                       ; RAH
        mov     word[ebx + device.mac+4], ax
 
        jmp     .mac_ok
 
  .try_eeprom:
        mov     dword[esi+0x14], 0x00000001
        mov     eax, [esi+0x14]
        shr     eax, 16
        mov     word[ebx + device.mac], ax
 
        mov     dword[esi+0x14], 0x00000101
        mov     eax, [esi+0x14]
        shr     eax, 16
        mov     word[ebx + device.mac+2], ax
 
        mov     dword[esi+0x14], 0x00000201
        mov     eax, [esi+0x14]
        shr     eax, 16
        mov     word[ebx + device.mac+4], ax
 
  .mac_ok:
        DEBUGF  1,"MAC = %x-%x-%x-%x-%x-%x\n",\
        [ebx + device.mac+0]:2,[ebx + device.mac+1]:2,[ebx + device.mac+2]:2,\
        [ebx + device.mac+3]:2,[ebx + device.mac+4]:2,[ebx + device.mac+5]:2
 
        ret
 
 
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;                                         ;;
;; Transmit                                ;;
;;                                         ;;
;; In: pointer to device structure in ebx  ;;
;;                                         ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
 
proc transmit stdcall bufferptr, buffersize
 
        pushf
        cli
 
        DEBUGF  1,"Transmitting packet, buffer:%x, size:%u\n", [bufferptr], [buffersize]
        mov     eax, [bufferptr]
        DEBUGF  1,"To: %x-%x-%x-%x-%x-%x From: %x-%x-%x-%x-%x-%x Type:%x%x\n",\
        [eax+00]:2,[eax+01]:2,[eax+02]:2,[eax+03]:2,[eax+04]:2,[eax+05]:2,\
        [eax+06]:2,[eax+07]:2,[eax+08]:2,[eax+09]:2,[eax+10]:2,[eax+11]:2,\
        [eax+13]:2,[eax+12]:2
 
        cmp     [buffersize], 1514
        ja      .fail
        cmp     [buffersize], 60
        jb      .fail
 
; Program the descriptor (use legacy mode)
        mov     edi, [ebx + device.cur_tx]
        DEBUGF  1, "Using TX desc: %u\n", edi
        shl     edi, 4                                          ; edi = edi * sizeof.TDESC
        lea     edi, [ebx + device.tx_desc + edi]
        mov     dword[edi + TX_RING_SIZE*sizeof.TDESC], eax     ; Store the data location (for driver)
        invoke  GetPhysAddr
        mov     [edi + TDESC.addr_l], eax                       ; Data location (for hardware)
        mov     [edi + TDESC.addr_h], 0
 
        mov     ecx, [buffersize]
        or      ecx, TXDESC_EOP + TXDESC_IFCS + TXDESC_RS
        mov     [edi + TDESC.length_cso_cmd], ecx
        mov     [edi + TDESC.status], 0
 
; Tell i8254x wich descriptor(s) we programmed, by moving the tail
        mov     edi, [ebx + device.mmio_addr]
        mov     eax, [ebx + device.cur_tx]
        inc     eax
        and     eax, TX_RING_SIZE-1
        mov     [ebx + device.cur_tx], eax
        mov     dword[edi + REG_TDT], eax                        ; TDT - Transmit Descriptor Tail
 
; Update stats
        inc     [ebx + device.packets_tx]
        mov     eax, [buffersize]
        add     dword[ebx + device.bytes_tx], eax
        adc     dword[ebx + device.bytes_tx + 4], 0
 
        call    clean_tx
 
        popf
        xor     eax, eax
        ret
 
  .fail:
        call    clean_tx
 
        DEBUGF  2,"Send failed\n"
        invoke  KernelFree, [bufferptr]
        popf
        or      eax, -1
        ret
 
endp
 
 
;;;;;;;;;;;;;;;;;;;;;;;
;;                   ;;
;; Interrupt handler ;;
;;                   ;;
;;;;;;;;;;;;;;;;;;;;;;;
 
align 4
int_handler:
 
        push    ebx esi edi
 
        DEBUGF  1,"INT\n"
;-------------------------------------------
; Find pointer of device wich made IRQ occur
 
        mov     ecx, [devices]
        test    ecx, ecx
        jz      .nothing
        mov     esi, device_list
  .nextdevice:
        mov     ebx, [esi]
        mov     edi, [ebx + device.mmio_addr]
        mov     eax, [edi + REG_ICR]
        test    eax, eax
        jnz     .got_it
  .continue:
        add     esi, 4
        dec     ecx
        jnz     .nextdevice
  .nothing:
        pop     edi esi ebx
        xor     eax, eax
 
        ret
 
  .got_it:
        DEBUGF  1,"Device: %x Status: %x\n", ebx, eax
 
;---------
; RX done?
 
        test    eax, ICR_RXDMT0 + ICR_RXT0
        jz      .no_rx
 
        push    eax ebx
  .retaddr:
        pop     ebx eax
; Get last descriptor addr
        mov     esi, [ebx + device.cur_rx]
        shl     esi, 4                                  ; esi = esi * sizeof.RDESC
        lea     esi, [ebx + device.rx_desc + esi]
        cmp     byte[esi + RDESC.status_h], 0           ; Check status field
        je      .no_rx
 
        push    eax ebx
        push    .retaddr
        movzx   ecx, word[esi + 8]                      ; Get the packet length
        DEBUGF  1,"got %u bytes\n", ecx
        push    ecx
        push    dword[esi + RX_RING_SIZE*sizeof.RDESC]  ; Get packet pointer
 
; Update stats
        add     dword[ebx + device.bytes_rx], ecx
        adc     dword[ebx + device.bytes_rx + 4], 0
        inc     [ebx + device.packets_rx]
 
; Allocate new descriptor
        push    esi
        invoke  KernelAlloc, MAX_PKT_SIZE
        pop     esi
        test    eax, eax
        jz      .out_of_mem
        mov     dword[esi + RX_RING_SIZE*sizeof.RDESC], eax
        invoke  GetPhysAddr
        mov     [esi + RDESC.addr_l], eax
        mov     [esi + RDESC.status_l], 0
        mov     [esi + RDESC.status_h], 0
 
; Move the receive descriptor tail
        mov     esi, [ebx + device.mmio_addr]
        mov     eax, [ebx + device.cur_rx]
        mov     [esi + REG_RDT], eax
 
; Move to next rx desc
        inc     [ebx + device.cur_rx]
        and     [ebx + device.cur_rx], RX_RING_SIZE-1
 
        jmp     [Eth_input]
 
  .out_of_mem:
        DEBUGF  2,"Out of memory!\n"
 
; Move to next rx desc
        inc     [ebx + device.cur_rx]
        and     [ebx + device.cur_rx], RX_RING_SIZE-1
 
        jmp     [Eth_input]
  .no_rx:
 
;--------------
; Link Changed?
 
        test    eax, ICR_LSC
        jz      .no_link
 
        DEBUGF  2,"Link Changed\n"
 
  .no_link:
 
;---------------
; Transmit done?
 
        test    eax, ICR_TXDW
        jz      .no_tx
 
        DEBUGF  1,"Transmit done\n"
 
;        call    clean_tx
 
  .no_tx:
        pop     edi esi ebx
        xor     eax, eax
        inc     eax
        ret
 
 
 
clean_tx:
 
  .txdesc_loop:
        mov     edi, [ebx + device.last_tx]
        shl     edi, 4                                  ; edi = edi * sizeof.TDESC
        lea     edi, [ebx + device.tx_desc + edi]
        test    [edi + TDESC.status], TXDESC_DD         ; Descriptor done?
        jz      .no_tx
        cmp     dword[edi + TX_RING_SIZE*sizeof.TDESC], 0
        je      .no_tx
 
        DEBUGF  1,"Cleaning up TX desc: 0x%x\n", edi
 
        push    ebx
        push    dword[edi + TX_RING_SIZE*sizeof.TDESC]
        mov     dword[edi + TX_RING_SIZE*sizeof.TDESC], 0
        invoke  KernelFree
        pop     ebx
 
        inc     [ebx + device.last_tx]
        and     [ebx + device.last_tx], TX_RING_SIZE-1
        jmp     .txdesc_loop
 
  .no_tx:
 
        ret
 
 
 
 
; End of code
 
data fixups
end data
 
include '../peimport.inc'
 
include_debug_strings
my_service      db 'I8254X', 0          ; max 16 chars include zero
 
align 4
devices         dd 0
device_list     rd MAX_DEVICES          ; This list contains all pointers to device structures the driver is handling
Subversion Repositories Kolibri OS

(root)/drivers/ethernet/i8254x.asm – Rev 5140 → 5156
