| 144,27 → 144,31 |
|---|
| EE_93C56_CMD_LENGTH = 11 ; start bit + cmd + 8bit ddress |
| |
| ; See chapter "5.7 Transmit Configuration Register" of RTL8139D(L).pdf |
| VER_RTL8139 = 1100000b |
| VER_RTL8139 = 1000000b |
| VER_RTL8139_K = 1100000b |
| VER_RTL8139A = 1110000b |
| VER_RTL8139AG = 1110100b |
| VER_RTL8139A_G = 1110010b |
| VER_RTL8139B = 1111000b |
| VER_RTL8130 = VER_RTL8139B |
| VER_RTL8130 = 1111100b |
| VER_RTL8139C = 1110100b |
| VER_RTL8100 = 1111010b |
| VER_RTL8100B = 1110101b |
| VER_RTL8139D = VER_RTL8100B |
| VER_RTL8139CP = 1110110b |
| VER_RTL8100_8139D = 1110101b |
| VER_RTL8101 = 1110111b |
| |
| IDX_RTL8139 = 0 |
| IDX_RTL8139A = 1 |
| IDX_RTL8139B = 2 |
| IDX_RTL8139C = 3 |
| IDX_RTL8100 = 4 |
| IDX_RTL8139D = 5 |
| IDX_RTL8139D = 6 |
| IDX_RTL8101 = 7 |
| IDX_UNKNOWN = 0 |
| IDX_RTL8139 = 1 |
| IDX_RTL8139_K = 2 |
| IDX_RTL8139A = 3 |
| IDX_RTL8139A_G = 4 |
| IDX_RTL8139B = 5 |
| IDX_RTL8130 = 6 |
| IDX_RTL8139C = 7 |
| IDX_RTL8100 = 8 |
| IDX_RTL8100_8139D = 9 |
| IDX_RTL8101 = 10 |
| |
| HW_VERSIONS = 10 |
| |
| ISR_SERR = 1 shl 15 |
| ISR_TIMEOUT = 1 shl 14 |
| ISR_LENCHG = 1 shl 13 |
| 327,8 → 331,8 |
|---|
| invoke PciRead8, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.interrupt_line |
| mov [ebx + device.irq_line], al |
| |
| DEBUGF 1, "Hooking into device, dev:%x, bus:%x, irq:%x, I/O addr:%x\n",\ |
| [ebx + device.pci_dev]:1,[ebx + device.pci_bus]:1,[ebx + device.irq_line]:1,[ebx + device.io_addr]:4 |
| DEBUGF 1, "Hooking into device, devfn:%x, bus:%x, irq:%x, I/O addr:%x\n",\ |
| [ebx + device.pci_dev]:2,[ebx + device.pci_bus]:2,[ebx + device.irq_line]:2,[ebx + device.io_addr]:4 |
| |
| ; Allocate the receive buffer |
| |
| 377,7 → 381,7 |
|---|
| dec [devices] |
| |
| .err: |
| DEBUGF 2, "Error, removing all data !\n" |
| DEBUGF 2, "Fatal error occured, aborting\n" |
| invoke KernelFree, [ebx + device.rx_buffer] |
| invoke KernelFree, ebx |
| |
| 421,57 → 425,48 |
|---|
| |
| ; Make the device a bus master |
| invoke PciRead32, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.command |
| or al, PCI_CMD_MASTER |
| or al, PCI_CMD_MASTER or PCI_CMD_PIO |
| invoke PciWrite32, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.command, eax |
| |
| ; wake up old chips |
| set_io [ebx + device.io_addr], 0 |
| set_io [ebx + device.io_addr], REG_HLTCLK |
| mov al, 'R' ; run the clock |
| out dx, al |
| |
| ; get chip version |
| set_io [ebx + device.io_addr], 0 |
| set_io [ebx + device.io_addr], REG_TXCONFIG + 2 |
| in ax, dx |
| set_io [ebx + device.io_addr], REG_TXCONFIG |
| in eax, dx |
| shr eax, 16 |
| shr ah, 2 |
| shr ax, 6 |
| and al, 01111111b |
| and al, 0x7f |
| DEBUGF 1, "Chip version: %x\n", eax:2 |
| |
| ; now find it in our array |
| mov ecx, HW_VER_ARRAY_SIZE-1 |
| .chip_ver_loop: |
| mov ecx, HW_VERSIONS |
| @@: |
| cmp al, [hw_ver_array + ecx] |
| je .chip_ver_found |
| je @f |
| dec ecx |
| jns .chip_ver_loop |
| .unknown: |
| mov ecx, 8 |
| .chip_ver_found: |
| cmp ecx, 8 |
| ja .unknown |
| |
| jnz @r |
| @@: |
| mov [ebx + device.hw_ver_id], cl |
| |
| mov ecx, [crosslist+ecx*4] |
| mov ecx, [hw_ver_names+ecx*4] |
| mov [ebx + device.name], ecx |
| |
| DEBUGF 1, "Chip version: %s\n", ecx |
| |
| ; wake up the chip |
| set_io [ebx + device.io_addr], 0 |
| set_io [ebx + device.io_addr], REG_HLTCLK |
| mov al, 'R' ; run the clock |
| out dx, al |
| cmp [ebx + device.hw_ver_id], IDX_RTL8139B |
| jae .new_chip |
| |
| ; unlock config and BMCR registers |
| set_io [ebx + device.io_addr], REG_9346CR |
| mov al, (1 shl BIT_93C46_EEM1) or (1 shl BIT_93C46_EEM0) |
| out dx, al |
| |
| ; enable power management |
| ; wake up older chips |
| .old_chip: |
| DEBUGF 1, "Wake up chip old style\n" |
| set_io [ebx + device.io_addr], REG_CONFIG1 |
| in al, dx |
| cmp [ebx + device.hw_ver_id], IDX_RTL8139B |
| jae .new_chip |
| ; wake up older chips |
| and al, not ((1 shl BIT_SLEEP) or (1 shl BIT_PWRDWN)) |
| out dx, al |
| jmp .finish_wake_up |
| jmp .done |
| |
| ; set LWAKE pin to active high (default value). |
| ; it is for Wake-On-LAN functionality of some motherboards. |
| 478,10 → 473,21 |
|---|
| ; this signal is used to inform the motherboard to execute a wake-up process. |
| ; only at newer chips. |
| .new_chip: |
| DEBUGF 1, "Wake up chip new style\n" |
| ; unlock config and BMCR registers |
| set_io [ebx + device.io_addr], 0 |
| set_io [ebx + device.io_addr], REG_9346CR |
| mov al, (1 shl BIT_93C46_EEM1) or (1 shl BIT_93C46_EEM0) |
| out dx, al |
| |
| ; |
| set_io [ebx + device.io_addr], REG_CONFIG1 |
| in al, dx |
| or al, (1 shl BIT_PMEn) |
| and al, not (1 shl BIT_LWACT) |
| out dx, al |
| |
| ; |
| set_io [ebx + device.io_addr], REG_CONFIG4 |
| in al, dx |
| and al, not (1 shl BIT_LWPTN) |
| 488,15 → 494,13 |
|---|
| out dx, al |
| |
| ; lock config and BMCR registers |
| .finish_wake_up: |
| xor al, al |
| set_io [ebx + device.io_addr], 0 |
| set_io [ebx + device.io_addr], REG_9346CR |
| out dx, al |
| |
| .done: |
| DEBUGF 1, "probing done!\n" |
| |
| xor eax, eax |
| |
| ret |
| |
| |
| 516,16 → 520,16 |
|---|
| mov al, 1 shl BIT_RST |
| out dx, al |
| mov cx, 1000 ; wait no longer for the reset |
| .wait_for_reset: |
| @@: |
| in al, dx |
| test al, 1 shl BIT_RST |
| jz .reset_completed ; RST remains 1 during reset |
| jz @f ; RST remains 1 during reset |
| dec cx |
| jns .wait_for_reset |
| jnz @r |
| DEBUGF 2, "Reset timeout!\n" |
| or eax, -1 |
| ret |
| .reset_completed: |
| @@: |
| |
| ; Read MAC address |
| call read_mac |
| 620,6 → 624,7 |
|---|
| ; Set the mtu, kernel will be able to send now |
| mov [ebx + device.mtu], 1514 |
| |
| ; Detect current link status |
| call link |
| |
| ; Indicate that we have successfully reset the card |
| 1122,40 → 1127,44 |
|---|
| |
| my_service db 'RTL8139',0 ; max 16 chars include zero |
| |
| device_1 db 'Realtek 8139',0 |
| device_2 db 'Realtek 8139A',0 |
| device_3 db 'Realtek 8139B',0 |
| device_4 db 'Realtek 8139C',0 |
| device_5 db 'Realtek 8100',0 |
| device_6 db 'Realtek 8139D',0 |
| device_7 db 'Realtek 8139CP',0 |
| device_8 db 'Realtek 8101',0 |
| device_unknown db 'Unknown RTL8139 clone', 0 |
| sz_unknown db 'Unknown RTL8139 clone', 0 |
| sz_RTL8139 db 'Realtek 8139',0 |
| sz_RTL8139_K db 'Realtek 8139 rev K',0 |
| sz_RTL8139A db 'Realtek 8139A',0 |
| sz_RTL8139A_G db 'Realtek 8139A rev G',0 |
| sz_RTL8139B db 'Realtek 8139B',0 |
| sz_RTL8130 db 'Realtek 8130',0 |
| sz_RTL8139C db 'Realtek 8139C',0 |
| sz_RTL8100 db 'Realtek 8100',0 |
| sz_RTL8100_8139D db 'Realtek 8100B / 8139D',0 |
| sz_RTL8101 db 'Realtek 8101',0 |
| |
| crosslist: |
| dd device_1 |
| dd device_2 |
| dd device_3 |
| dd device_4 |
| dd device_5 |
| dd device_6 |
| dd device_7 |
| dd device_8 |
| dd device_unknown |
| hw_ver_names: |
| dd sz_unknown |
| dd sz_RTL8139 |
| dd sz_RTL8139_K |
| dd sz_RTL8139A |
| dd sz_RTL8139A_G |
| dd sz_RTL8139B |
| dd sz_RTL8130 |
| dd sz_RTL8139C |
| dd sz_RTL8100 |
| dd sz_RTL8100_8139D |
| dd sz_RTL8101 |
| |
| hw_ver_array: ; This array is used by the probe routine to find out wich version of the RTL8139 we are working with |
| db 0 |
| db VER_RTL8139 |
| db VER_RTL8139_K |
| db VER_RTL8139A |
| db VER_RTL8139A_G |
| db VER_RTL8139B |
| db VER_RTL8130 |
| db VER_RTL8139C |
| db VER_RTL8100 |
| db VER_RTL8139D |
| db VER_RTL8139CP |
| db VER_RTL8100_8139D |
| db VER_RTL8101 |
| db 0 |
| |
| HW_VER_ARRAY_SIZE = $-hw_ver_array |
| |
| include_debug_strings ; All data wich FDO uses will be included here |
| |
| align 4 |