| 30,7 → 30,7 |
|---|
| |
| DEBUG = 1 |
| __DEBUG__ = 1 |
| __DEBUG_LEVEL__ = 2 |
| __DEBUG_LEVEL__ = 2 ; 1 = verbose, 2 = errors only |
| |
| include '../proc32.inc' |
| include '../imports.inc' |
| 194,7 → 194,7 |
|---|
| |
| .entry: |
| |
| DEBUGF 1,"Loading %s driver\n", my_service |
| DEBUGF 1,"Loading driver\n" |
| stdcall RegService, my_service, service_proc |
| ret |
| |
| 294,7 → 294,7 |
|---|
| |
| PCI_find_irq |
| |
| DEBUGF 2,"Hooking into device, dev:%x, bus:%x, irq:%x, addr:%x\n",\ |
| DEBUGF 1,"Hooking into device, dev:%x, bus:%x, irq:%x, addr:%x\n",\ |
| [device.pci_dev]:1,[device.pci_bus]:1,[device.irq_line]:1,[device.io_addr]:4 |
| |
| ; Ok, the eth_device structure is ready, let's probe the device |
| 376,7 → 376,7 |
|---|
| align 4 |
| probe: |
| |
| DEBUGF 1,"Probing i8255x\n" |
| DEBUGF 1,"Probing\n" |
| |
| PCI_make_bus_master |
| |
| 400,7 → 400,7 |
|---|
| jmp .found |
| |
| .notfound: |
| DEBUGF 1,"ERROR: Unsupported device!\n" |
| DEBUGF 2,"Unsupported device!\n" |
| or eax, -1 |
| ret |
| |
| 427,12 → 427,12 |
|---|
| stdcall AttachIntHandler, eax, int_handler, dword 0 |
| test eax, eax |
| jnz @f |
| DEBUGF 1,"\nCould not attach int handler!\n" |
| DEBUGF 2,"Could not attach int handler!\n" |
| ; or eax, -1 |
| ; ret |
| @@: |
| |
| DEBUGF 1,"Resetting %s\n", my_service |
| DEBUGF 1,"Resetting\n" |
| |
| ;--------------- |
| ; reset the card |
| 558,7 → 558,7 |
|---|
| |
| ; Indicate that we have successfully reset the card |
| |
| DEBUGF 1,"Resetting %s complete\n", my_service |
| DEBUGF 1,"Reset complete\n" |
| |
| mov [device.mtu], 1514 |
| |
| 693,7 → 693,7 |
|---|
| |
| push ebx esi edi |
| |
| DEBUGF 1,"\n%s int\n", my_service |
| DEBUGF 1,"INT\n" |
| |
| ; find pointer of device wich made IRQ occur |
| |
| 861,7 → 861,7 |
|---|
| align 4 |
| ee_read: ; esi = address to read |
| |
| DEBUGF 1,"Eeprom read from 0x%x", esi |
| DEBUGF 1,"Eeprom read from 0x%x\n", esi |
| |
| set_io 0 |
| set_io reg_eeprom |
| 931,7 → 931,7 |
|---|
| out dx, ax |
| |
| |
| DEBUGF 1,"=0x%x\n", esi:4 |
| DEBUGF 1,"0x%x\n", esi:4 |
| ret |
| |
| |
| 1011,8 → 1011,6 |
|---|
| align 4 |
| ee_get_width: |
| |
| ; DEBUGF 1,"Eeprom get width\n" |
| |
| set_io 0 |
| set_io reg_eeprom |
| |
| 1044,21 → 1042,20 |
|---|
| test al, EE_DO |
| jnz .loop |
| |
| .give_up: |
| xor al, al |
| out dx, al ; de-activate eeprom |
| |
| sub cl, 3 ; dont count the opcode bits |
| |
| mov [device.ee_bus_width], cl |
| DEBUGF 1,"Eeprom width=%u bit\n", ecx |
| |
| ret |
| |
| ;----------------------- |
| ; de-activate the eeprom |
| .give_up: |
| DEBUGF 2, "Eeprom not found!\n" |
| |
| xor eax, eax |
| out dx, eax |
| xor al, al |
| out dx, al ; de-activate eeprom |
| |
| ret |
| |