Subversion Repositories Kolibri OS

Compare Revisions

Regard whitespace Rev 4574 → Rev 4575

/kernel/trunk/kernel.asm
776,7 → 776,29
call unmask_timer
stdcall enable_irq, 2 ; @#$%! PIC
stdcall enable_irq, 13 ; co-processor
 
;-----------------------------------------------------------------------------
; show SVN version of kernel on the message board
;-----------------------------------------------------------------------------
mov eax, [version_inf.rev]
DEBUGF 1, "K : kernel SVN r%d\n", eax
;-----------------------------------------------------------------------------
; show CPU count on the message board
;-----------------------------------------------------------------------------
mov eax, [cpu_count]
test eax, eax
jnz @F
mov al, 1 ; at least one CPU
@@:
DEBUGF 1, "K : %d CPU detected\n", eax
;-----------------------------------------------------------------------------
; detect Floppy drives
;-----------------------------------------------------------------------------
mov esi, boot_detectfloppy
call boot_log
include 'detect/dev_fd.inc'
;-----------------------------------------------------------------------------
; START of initialisation IDE ATA code
;-----------------------------------------------------------------------------
cmp [IDEContrProgrammingInterface], 0
je @f
 
796,14 → 818,15
add dx, 2 ;0x376
out dx, al
@@:
; show base variables of IDE controller
DEBUGF 1, "K : BAR0 %x \n", [IDE_BAR0_val]:4
DEBUGF 1, "K : BAR1 %x \n", [IDE_BAR1_val]:4
DEBUGF 1, "K : BAR2 %x \n", [IDE_BAR2_val]:4
DEBUGF 1, "K : BAR3 %x \n", [IDE_BAR3_val]:4
DEBUGF 1, "K : BAR4 %x \n", [IDEContrRegsBaseAddr]:4
DEBUGF 1, "K : IDEContrProgrammingInterface %x \n", [IDEContrProgrammingInterface]:4
DEBUGF 1, "K : IDE_Interrupt %x \n", [IDE_Interrupt]:4
;-----------------------------------------------------------------------------
;!!!!!!!!!!!!!!!!!!!!!!!!!!
; mov esi, boot_detectdisks
; call boot_log
;include 'detect/disks.inc'
mov esi, boot_detectfloppy
call boot_log
include 'detect/dev_fd.inc'
mov esi, boot_detecthdcd
call boot_log
include 'detect/dev_hdcd.inc'
813,8 → 836,132
mov esi, boot_detectpart
call boot_log
include 'detect/sear_par.inc'
;!!!!!!!!!!!!!!!!!!!!!!!!!!
;-----------------------------------------------------------------------------
mov dx, [IDEContrRegsBaseAddr]
; test whether it is our interrupt?
add dx, 2
in al, dx
test al, 100b
jz @f
; clear Bus Master IDE Status register
; clear Interrupt bit
out dx, al
@@:
add dx, 8
; test whether it is our interrupt?
in al, dx
test al, 100b
jz @f
; clear Bus Master IDE Status register
; clear Interrupt bit
out dx, al
@@:
; read status register and remove the interrupt request
mov dx, [IDE_BAR0_val] ;0x1F0
add dx, 0x7 ;0x1F7
in al, dx
mov dx, [IDE_BAR2_val] ;0x170
add dx, 0x7 ;0x177
in al, dx
;-----------------------------------------------------------------------------
push eax edx
mov dx, [IDEContrRegsBaseAddr]
xor eax, eax
add dx, 2
in al, dx
DEBUGF 1, "K : Primary Bus Master IDE Status Register %x\n", eax
 
add dx, 8
in al, dx
DEBUGF 1, "K : Secondary Bus Master IDE Status Register %x\n", eax
pop edx eax
 
cmp [IDEContrRegsBaseAddr], 0
setnz [dma_hdd]
 
cmp [IDEContrProgrammingInterface], 0
je set_interrupts_for_IDE_controllers.continue
;-----------------------------------------------------------------------------
; set interrupts for IDE Controller
;-----------------------------------------------------------------------------
mov esi, boot_set_int_IDE
call boot_log
set_interrupts_for_IDE_controllers:
mov ax, [IDEContrProgrammingInterface]
cmp ax, 0x0180
je .pata_ide
 
cmp ax, 0x018a
jne .sata_ide
;--------------------------------------
.pata_ide:
cmp [IDEContrRegsBaseAddr], 0
je .end_set_interrupts
 
stdcall attach_int_handler, 14, IDE_irq_14_handler, 0
DEBUGF 1, "K : Set IDE IRQ14 return code %x\n", eax
stdcall attach_int_handler, 15, IDE_irq_15_handler, 0
DEBUGF 1, "K : Set IDE IRQ15 return code %x\n", eax
jmp .enable_IDE_interrupt
;--------------------------------------
.sata_ide:
cmp ax, 0x0185
je .sata_ide_1
 
cmp ax, 0x018f
jne .end_set_interrupts
;--------------------------------------
.sata_ide_1:
cmp [IDEContrRegsBaseAddr], 0
je .end_set_interrupts
 
mov ax, [IDE_Interrupt]
movzx eax, al
stdcall attach_int_handler, eax, IDE_common_irq_handler, 0
DEBUGF 1, "K : Set IDE IRQ%d return code %x\n", [IDE_Interrupt]:1, eax
;--------------------------------------
.enable_IDE_interrupt:
mov esi, boot_enabling_ide
call boot_log
; Enable interrupts in IDE controller for DMA
mov al, 0
mov ah, [DRIVE_DATA+1]
test ah, 10100000b
jz @f
 
DEBUGF 1, "K : IDE CH1 PIO, because ATAPI drive present\n"
jmp .ch2_check
@@:
mov dx, [IDE_BAR1_val] ;0x3F4
add dx, 2 ;0x3F6
out dx, al
DEBUGF 1, "K : IDE CH1 DMA enabled\n"
.ch2_check:
test ah, 1010b
jz @f
 
DEBUGF 1, "K : IDE CH2 PIO, because ATAPI drive present\n"
jmp .end_set_interrupts
@@:
mov dx, [IDE_BAR3_val] ;0x374
add dx, 2 ;0x376
out dx, al
DEBUGF 1, "K : IDE CH2 DMA enabled\n"
;--------------------------------------
.end_set_interrupts:
;-----------------------------------------------------------------------------
cmp [dma_hdd], 0
je .print_pio
.print_dma:
DEBUGF 1, "K : IDE DMA mode\n"
jmp .continue
 
.print_pio:
DEBUGF 1, "K : IDE PIO mode\n"
.continue:
;-----------------------------------------------------------------------------
; END of initialisation IDE ATA code
;-----------------------------------------------------------------------------
mov esi, boot_init_sys
call boot_log
call Parser_params
827,7 → 974,6
include 'boot/rdload.inc'
;!!!!!!!!!!!!!!!!!!!!!!!
end if
; mov [dma_hdd],1
 
if 0
mov ax, [OS_BASE+0x10000+bx_from_load]
881,34 → 1027,7
 
mov [pci_access_enabled], 1
call pci_enum
;-----------------------------------------------------------------------------
mov dx, [IDEContrRegsBaseAddr]
; test whether it is our interrupt?
add dx, 2
in al, dx
test al, 100b
jz @f
; clear Bus Master IDE Status register
; clear Interrupt bit
out dx, al
@@:
add dx, 8
; test whether it is our interrupt?
in al, dx
test al, 100b
jz @f
; clear Bus Master IDE Status register
; clear Interrupt bit
out dx, al
@@:
; read status register and remove the interrupt request
mov dx, [IDE_BAR0_val] ;0x1F0
add dx, 0x7 ;0x1F7
in al, dx
mov dx, [IDE_BAR2_val] ;0x170
add dx, 0x7 ;0x177
in al, dx
;-----------------------------------------------------------------------------
 
include "detect/vortex86.inc" ; Vortex86 SoC detection code
 
stdcall load_driver, szVidintel
1126,25 → 1245,6
out dx, al
 
end if
 
mov eax, [version_inf.rev]
DEBUGF 1, "K : kernel SVN r%d\n", eax
 
mov eax, [cpu_count]
test eax, eax
jnz @F
mov al, 1 ; at least one CPU
@@:
DEBUGF 1, "K : %d CPU detected\n", eax
 
DEBUGF 1, "K : BAR0 %x \n", [IDE_BAR0_val]:4
DEBUGF 1, "K : BAR1 %x \n", [IDE_BAR1_val]:4
DEBUGF 1, "K : BAR2 %x \n", [IDE_BAR2_val]:4
DEBUGF 1, "K : BAR3 %x \n", [IDE_BAR3_val]:4
DEBUGF 1, "K : BAR4 %x \n", [IDEContrRegsBaseAddr]:4
DEBUGF 1, "K : IDEContrProgrammingInterface %x \n", [IDEContrProgrammingInterface]:4
DEBUGF 1, "K : IDE_Interrupt %x \n", [IDE_Interrupt]:4
 
; START MULTITASKING
 
; A 'All set - press ESC to start' messages if need
1157,102 → 1257,6
jne .bll1
end if
 
push eax edx
mov dx, [IDEContrRegsBaseAddr]
xor eax, eax
add dx, 2
in al, dx
DEBUGF 1, "K : Primary Bus Master IDE Status Register %x\n", eax
 
add dx, 8
in al, dx
DEBUGF 1, "K : Secondary Bus Master IDE Status Register %x\n", eax
pop edx eax
 
cmp [IDEContrRegsBaseAddr], 0
setnz [dma_hdd]
 
cmp [IDEContrProgrammingInterface], 0
je set_interrupts_for_IDE_controllers.continue
;-----------------------------------------------------------------------------
; set interrupts for IDE Controller
;-----------------------------------------------------------------------------
mov esi, boot_set_int_IDE
call boot_log
set_interrupts_for_IDE_controllers:
mov ax, [IDEContrProgrammingInterface]
cmp ax, 0x0180
je .pata_ide
 
cmp ax, 0x018a
jne .sata_ide
;--------------------------------------
.pata_ide:
cmp [IDEContrRegsBaseAddr], 0
je .end_set_interrupts
 
stdcall attach_int_handler, 14, IDE_irq_14_handler, 0
DEBUGF 1, "K : Set IDE IRQ14 return code %x\n", eax
stdcall attach_int_handler, 15, IDE_irq_15_handler, 0
DEBUGF 1, "K : Set IDE IRQ15 return code %x\n", eax
jmp .enable_IDE_interrupt
;--------------------------------------
.sata_ide:
cmp ax, 0x0185
je .sata_ide_1
 
cmp ax, 0x018f
jne .end_set_interrupts
;--------------------------------------
.sata_ide_1:
cmp [IDEContrRegsBaseAddr], 0
je .end_set_interrupts
 
mov ax, [IDE_Interrupt]
movzx eax, al
stdcall attach_int_handler, eax, IDE_common_irq_handler, 0
DEBUGF 1, "K : Set IDE IRQ%d return code %x\n", [IDE_Interrupt]:1, eax
;--------------------------------------
.enable_IDE_interrupt:
mov esi, boot_enabling_ide
call boot_log
; Enable interrupts in IDE controller for DMA
mov al, 0
mov ah, [DRIVE_DATA+1]
test ah, 10100000b
jz @f
 
DEBUGF 1, "K : IDE CH1 PIO, because ATAPI drive present\n"
jmp .ch2_check
@@:
mov dx, [IDE_BAR1_val] ;0x3F4
add dx, 2 ;0x3F6
out dx, al
DEBUGF 1, "K : IDE CH1 DMA enabled\n"
.ch2_check:
test ah, 1010b
jz @f
 
DEBUGF 1, "K : IDE CH2 PIO, because ATAPI drive present\n"
jmp .end_set_interrupts
@@:
mov dx, [IDE_BAR3_val] ;0x374
add dx, 2 ;0x376
out dx, al
DEBUGF 1, "K : IDE CH2 DMA enabled\n"
;--------------------------------------
.end_set_interrupts:
;-----------------------------------------------------------------------------
cmp [dma_hdd], 0
je .print_pio
.print_dma:
DEBUGF 1, "K : IDE DMA mode\n"
jmp .continue
 
.print_pio:
DEBUGF 1, "K : IDE PIO mode\n"
.continue:
 
mov [timer_ticks_enable], 1 ; for cd driver
 
sti