Subversion Repositories Kolibri OS

Compare Revisions

Regard whitespace Rev 6014 → Rev 6015

/kernel/trunk/blkdev/hd_drv.inc
504,30 → 504,60
IDE_irq_14_handler:
IDE_irq_15_handler:
IDE_common_irq_handler:
; Most of the time, we are here because we have requested
; a DMA transfer for the corresponding drive.
; However,
; a) we can be here because IDE IRQ is shared with some other device,
; that device has actually raised IRQ,
; it has nothing to do with IDE;
; b) we can be here because IDE controller just does not want
; to be silent and reacts to something even though
; we have, in theory, disabled IRQs.
; If the interrupt corresponds to our current request,
; remove the interrupt request and raise the event for the waiting code.
; In the case a), just return zero - not our interrupt.
; In the case b), remove the interrupt request and hope for the best.
; DEBUGF 1, 'K : IDE_irq_handler %x\n', [IDE_common_irq_param]:2
cmp [IDE_common_irq_param], 0
jz .exit
pushfd
cli
pushad
mov ecx, [IDE_controller_pointer]
mov ecx, [esp+4]
mov dx, [ecx+IDE_DATA.RegsBaseAddres]
cmp [IDE_common_irq_param], 14
jz @f
add dx, 8
@@:
add edx, 2 ; Bus Master IDE Status register
in al, dx
test al, 4
jz @f
mov [IDE_common_irq_param], 0
jnz .interrupt_from_primary
add edx, 8
in al, dx
test al, 4
jnz .interrupt_from_secondary
.exit_notour:
xor eax, eax ; not our interrupt
ret
.interrupt_from_primary:
out dx, al ; clear Interrupt bit
sub edx, 2
xor eax, eax
out dx, al ; clear Bus Master IDE Command register
mov edx, [hdbase]
mov dx, [ecx+IDE_DATA.BAR0_val]
add edx, 7
in al, dx ; read status register
cmp [IDE_common_irq_param], 14
jz .raise
.exit_our:
mov al, 1
ret
.interrupt_from_secondary:
out dx, al ; clear Interrupt bit
sub edx, 2
xor eax, eax
out dx, al ; clear Bus Master IDE Command register
mov dx, [ecx+IDE_DATA.BAR2_val]
add edx, 7
in al, dx ; read status register
cmp [IDE_common_irq_param], 15
jnz .exit_our
.raise:
cmp ecx, [IDE_controller_pointer]
jnz .exit_our
pushad
mov eax, [eventPointer]
mov ebx, [eventID]
xor edx, edx
534,51 → 564,6
xor esi, esi
call raise_event
popad
popfd
mov al, 1 ; remove the interrupt request
ret
@@:
popad
popfd
.exit:
xor eax, eax ; not our interrupt
ret
;-----------------------------------------------------------------
proc clear_pci_ide_interrupts
mov esi, pcidev_list
align 4
.loop:
mov esi, [esi+PCIDEV.fd]
cmp esi, pcidev_list
jz .done
 
; cmp [esi+PCIDEV.class], 0x01018F
mov eax, [esi+PCIDEV.class]
shr eax, 4
cmp eax, 0x01018
jnz .loop
 
mov ah, [esi+PCIDEV.bus]
mov al, 2
mov bh, [esi+PCIDEV.devfn]
mov bl, 0x20
call pci_read_reg
 
and eax, 0FFFCh
mov edx, eax
add edx, 2
in al, dx
DEBUGF 1,'K : clear_pci_ide_interrupts: port[%x] = %x ',dx,al
out dx, al
in al, dx
DEBUGF 1,'-> %x; ',al
add edx, 8
in al, dx
DEBUGF 1,'port[%x] = %x ',dx,al
out dx, al
in al, dx
DEBUGF 1,'-> %x\n',al
jmp .loop
.done:
ret
endp
/kernel/trunk/core/irq.inc
203,6 → 203,8
; Note: this still isn't 100% correct, because two IRQs can fire simultaneously,
; the better way would be to find the correct IRQ, but I don't know how to do
; this in that case.
cmp ebp, 1
jz .fail
push ebp
xor ebp, ebp
.try_other_irqs:
/kernel/trunk/detect/init_ata.inc
378,9 → 378,11
je .end_set_interrupts
 
push ecx
stdcall attach_int_handler, 14, IDE_irq_14_handler, 0
stdcall attach_int_handler, 14, IDE_irq_14_handler, ecx
pop ecx
DEBUGF 1, "K : Set IDE IRQ14 return code %x\n", eax
stdcall attach_int_handler, 15, IDE_irq_15_handler, 0
push ecx
stdcall attach_int_handler, 15, IDE_irq_15_handler, ecx
DEBUGF 1, "K : Set IDE IRQ15 return code %x\n", eax
pop ecx
 
400,20 → 402,18
; the IDE controller 01018f. For this reason, the interrupt handler
; does not need to be installed if both channel IDE controller
; running in PIO mode.
 
; ...unfortunately, PCI interrupt can be shared with other devices
; which could enable it without consulting IDE code.
; So install the handler anyways and try to process
; even those interrupts which we are not expecting.
cmp [ecx+IDE_DATA.RegsBaseAddres], 0
je .end_set_interrupts
 
cmp [ecx+IDE_DATA.dma_hdd_channel_1], 0
jne @f
 
cmp [ecx+IDE_DATA.dma_hdd_channel_2], 0
je .end_set_interrupts
;--------------------------------------
@@:
mov ax, [ecx+IDE_DATA.Interrupt]
movzx eax, al
push ecx
stdcall attach_int_handler, eax, IDE_common_irq_handler, 0
stdcall attach_int_handler, eax, IDE_common_irq_handler, ecx
pop ecx
DEBUGF 1, "K : Set IDE IRQ%d return code %x\n", [ecx+IDE_DATA.Interrupt]:1, eax
;--------------------------------------
/kernel/trunk/kernel.asm
996,8 → 996,6
; mov esi, boot_devices
; call boot_log
 
call clear_pci_ide_interrupts
 
include "detect/vortex86.inc" ; Vortex86 SoC detection code
 
stdcall load_pe_driver, szVidintel, 0