23,43 → 23,27 |
d80x25_bottom_num = 3 |
|
msg_apm db " APM x.x ", 0 |
vervesa db "Version of Vesa: Vesa x.x",13,10,0 |
novesa db "Display: EGA/CGA",13,10,0 |
s_vesa db "Version of VESA: " |
.ver db "?.?",13,10,0 |
|
gr_mode db "Select a videomode: ",13,10,0 |
;s_bpp db 13,10,186," «ã¡¨ 梥â : " |
; .bpp dw "??" |
; db 13,10,0 |
|
vrrmprint db "Apply VRR? (picture frequency greater than 60Hz" |
db " only for transfers:",13,10 |
db 186," 1024*768->800*600 and 800*600->640*480) [1-yes,2-no]:",0 |
|
|
ask_bd db "Add disks visible by BIOS emulated in V86-mode? [1-yes, 2-no]: ",0 |
|
if defined extended_primary_loader |
bdev db "Load ramdisk from [1-floppy; 2-kolibri.img]: ",0 |
else |
bdev db "Load ramdisk from [1-floppy; 2-C:\kolibri.img (FAT32);" |
db 13,10,186," " |
db "3-use preloaded ram-image from kernel restart;" |
db 13,10,186," " |
db "4-create blank image]: ",0 |
else |
bdev db "Load ramdisk from [1-floppy; 2-kolibri.img]: ",0 |
end if |
probetext db 13,10,13,10,186," Use standart graphics mode? [1-yes, " |
db "2-probe bios (Vesa 3.0)]: ",0 |
;memokz256 db 13,10,186," RAM 256 Mb",0 |
;memokz128 db 13,10,186," RAM 128 Mb",0 |
;memokz64 db 13,10,186," RAM 64 Mb",0 |
;memokz32 db 13,10,186," RAM 32 Mb",0 |
;memokz16 db 13,10,186," RAM 16 Mb",0 |
|
prnotfnd db "Fatal - Videomode not found.",0 |
;modena db "Fatal - VBE 0x112+ required.",0 |
|
not386 db "Fatal - CPU 386+ required.",0 |
btns db "Fatal - Can't determine color depth.",0 |
fatalsel db "Fatal - Graphics mode not supported by hardware.",0 |
pres_key db "Press any key to choose a new videomode.",0 |
badsect db 13,10,186," Fatal - Bad sector. Replace floppy.",0 |
77,21 → 61,15 |
current_cfg_msg db "Current settings:",13,10,0 |
curvideo_msg db " [a] Videomode: ",0 |
|
;modes_msg dw mode4,mode1,mode2,mode3 |
;modevesa20 db " with LFB",0 |
;modevesa12 db ", VESA 1.2 Bnk",0 |
mode0 db "320x200, EGA/CGA 256 colors",13,10,0 |
mode9 db "640x480, VGA 16 colors",13,10,0 |
|
;probeno_msg db " (standard mode)",0 |
;probeok_msg db " (check nonstandard modes)",0 |
;dma_msg db " [b] Use DMA for HDD access:",0 |
usebd_msg db " [b] Add disks visible by BIOS:",0 |
on_msg db " on",13,10,0 |
off_msg db " off",13,10,0 |
;readonly_msg db " only for reading",13,10,0 |
vrrm_msg db " [c] Use VRR:",0 |
preboot_device_msg db " [d] Floppy image: ",0 |
|
preboot_device_msg db " [c] Floppy image: ",0 |
|
if defined extended_primary_loader |
preboot_device_msgs dw 0,pdm1,pdm2,0 |
pdm1 db "real floppy",13,10,0 |
103,7 → 81,9 |
pdm3 db "use already loaded image",13,10,0 |
pdm4 db "create blank image",13,10,0 |
end if |
|
loading_msg db "Loading KolibriOS...",0 |
|
if ~ defined extended_primary_loader |
save_quest db "Remember current settings? [y/n]: ",0 |
loader_block_error db "Bootloader data invalid, I cannot continue. Stopped.",0 |
116,7 → 96,6 |
_bt db 186,' ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÙ',13,10,0 |
|
remark1 db "Default values were selected to match most of configurations, but not all.",0 |
remark2 db "If you have CRT-monitor, enable VRR in the item [c].",0 |
remark3 db "If the system does not boot, try to disable the item [b].",0 |
remarks dw remark1, remark2, remark3 |
num_remarks = 3 |
remark2 db "If the system does not boot, try to disable the item [b].",0 |
remarks dw remark1, remark2 |
num_remarks = 2 |