| 35,46 → 35,91 |
|---|
| * structures). |
| */ |
| |
| /** |
| * enum drm_mode_status - hardware support status of a mode |
| * @MODE_OK: Mode OK |
| * @MODE_HSYNC: hsync out of range |
| * @MODE_VSYNC: vsync out of range |
| * @MODE_H_ILLEGAL: mode has illegal horizontal timings |
| * @MODE_V_ILLEGAL: mode has illegal horizontal timings |
| * @MODE_BAD_WIDTH: requires an unsupported linepitch |
| * @MODE_NOMODE: no mode with a matching name |
| * @MODE_NO_INTERLACE: interlaced mode not supported |
| * @MODE_NO_DBLESCAN: doublescan mode not supported |
| * @MODE_NO_VSCAN: multiscan mode not supported |
| * @MODE_MEM: insufficient video memory |
| * @MODE_VIRTUAL_X: mode width too large for specified virtual size |
| * @MODE_VIRTUAL_Y: mode height too large for specified virtual size |
| * @MODE_MEM_VIRT: insufficient video memory given virtual size |
| * @MODE_NOCLOCK: no fixed clock available |
| * @MODE_CLOCK_HIGH: clock required is too high |
| * @MODE_CLOCK_LOW: clock required is too low |
| * @MODE_CLOCK_RANGE: clock/mode isn't in a ClockRange |
| * @MODE_BAD_HVALUE: horizontal timing was out of range |
| * @MODE_BAD_VVALUE: vertical timing was out of range |
| * @MODE_BAD_VSCAN: VScan value out of range |
| * @MODE_HSYNC_NARROW: horizontal sync too narrow |
| * @MODE_HSYNC_WIDE: horizontal sync too wide |
| * @MODE_HBLANK_NARROW: horizontal blanking too narrow |
| * @MODE_HBLANK_WIDE: horizontal blanking too wide |
| * @MODE_VSYNC_NARROW: vertical sync too narrow |
| * @MODE_VSYNC_WIDE: vertical sync too wide |
| * @MODE_VBLANK_NARROW: vertical blanking too narrow |
| * @MODE_VBLANK_WIDE: vertical blanking too wide |
| * @MODE_PANEL: exceeds panel dimensions |
| * @MODE_INTERLACE_WIDTH: width too large for interlaced mode |
| * @MODE_ONE_WIDTH: only one width is supported |
| * @MODE_ONE_HEIGHT: only one height is supported |
| * @MODE_ONE_SIZE: only one resolution is supported |
| * @MODE_NO_REDUCED: monitor doesn't accept reduced blanking |
| * @MODE_NO_STEREO: stereo modes not supported |
| * @MODE_STALE: mode has become stale |
| * @MODE_BAD: unspecified reason |
| * @MODE_ERROR: error condition |
| * |
| * This enum is used to filter out modes not supported by the driver/hardware |
| * combination. |
| */ |
| enum drm_mode_status { |
| MODE_OK = 0, /* Mode OK */ |
| MODE_HSYNC, /* hsync out of range */ |
| MODE_VSYNC, /* vsync out of range */ |
| MODE_H_ILLEGAL, /* mode has illegal horizontal timings */ |
| MODE_V_ILLEGAL, /* mode has illegal horizontal timings */ |
| MODE_BAD_WIDTH, /* requires an unsupported linepitch */ |
| MODE_NOMODE, /* no mode with a matching name */ |
| MODE_NO_INTERLACE, /* interlaced mode not supported */ |
| MODE_NO_DBLESCAN, /* doublescan mode not supported */ |
| MODE_NO_VSCAN, /* multiscan mode not supported */ |
| MODE_MEM, /* insufficient video memory */ |
| MODE_VIRTUAL_X, /* mode width too large for specified virtual size */ |
| MODE_VIRTUAL_Y, /* mode height too large for specified virtual size */ |
| MODE_MEM_VIRT, /* insufficient video memory given virtual size */ |
| MODE_NOCLOCK, /* no fixed clock available */ |
| MODE_CLOCK_HIGH, /* clock required is too high */ |
| MODE_CLOCK_LOW, /* clock required is too low */ |
| MODE_CLOCK_RANGE, /* clock/mode isn't in a ClockRange */ |
| MODE_BAD_HVALUE, /* horizontal timing was out of range */ |
| MODE_BAD_VVALUE, /* vertical timing was out of range */ |
| MODE_BAD_VSCAN, /* VScan value out of range */ |
| MODE_HSYNC_NARROW, /* horizontal sync too narrow */ |
| MODE_HSYNC_WIDE, /* horizontal sync too wide */ |
| MODE_HBLANK_NARROW, /* horizontal blanking too narrow */ |
| MODE_HBLANK_WIDE, /* horizontal blanking too wide */ |
| MODE_VSYNC_NARROW, /* vertical sync too narrow */ |
| MODE_VSYNC_WIDE, /* vertical sync too wide */ |
| MODE_VBLANK_NARROW, /* vertical blanking too narrow */ |
| MODE_VBLANK_WIDE, /* vertical blanking too wide */ |
| MODE_PANEL, /* exceeds panel dimensions */ |
| MODE_INTERLACE_WIDTH, /* width too large for interlaced mode */ |
| MODE_ONE_WIDTH, /* only one width is supported */ |
| MODE_ONE_HEIGHT, /* only one height is supported */ |
| MODE_ONE_SIZE, /* only one resolution is supported */ |
| MODE_NO_REDUCED, /* monitor doesn't accept reduced blanking */ |
| MODE_NO_STEREO, /* stereo modes not supported */ |
| MODE_UNVERIFIED = -3, /* mode needs to reverified */ |
| MODE_BAD = -2, /* unspecified reason */ |
| MODE_ERROR = -1 /* error condition */ |
| MODE_OK = 0, |
| MODE_HSYNC, |
| MODE_VSYNC, |
| MODE_H_ILLEGAL, |
| MODE_V_ILLEGAL, |
| MODE_BAD_WIDTH, |
| MODE_NOMODE, |
| MODE_NO_INTERLACE, |
| MODE_NO_DBLESCAN, |
| MODE_NO_VSCAN, |
| MODE_MEM, |
| MODE_VIRTUAL_X, |
| MODE_VIRTUAL_Y, |
| MODE_MEM_VIRT, |
| MODE_NOCLOCK, |
| MODE_CLOCK_HIGH, |
| MODE_CLOCK_LOW, |
| MODE_CLOCK_RANGE, |
| MODE_BAD_HVALUE, |
| MODE_BAD_VVALUE, |
| MODE_BAD_VSCAN, |
| MODE_HSYNC_NARROW, |
| MODE_HSYNC_WIDE, |
| MODE_HBLANK_NARROW, |
| MODE_HBLANK_WIDE, |
| MODE_VSYNC_NARROW, |
| MODE_VSYNC_WIDE, |
| MODE_VBLANK_NARROW, |
| MODE_VBLANK_WIDE, |
| MODE_PANEL, |
| MODE_INTERLACE_WIDTH, |
| MODE_ONE_WIDTH, |
| MODE_ONE_HEIGHT, |
| MODE_ONE_SIZE, |
| MODE_NO_REDUCED, |
| MODE_NO_STEREO, |
| MODE_STALE = -3, |
| MODE_BAD = -2, |
| MODE_ERROR = -1 |
| }; |
| |
| #define DRM_MODE_TYPE_CLOCK_CRTC_C (DRM_MODE_TYPE_CLOCK_C | \ |
| 96,17 → 141,125 |
|---|
| |
| #define DRM_MODE_FLAG_3D_MAX DRM_MODE_FLAG_3D_SIDE_BY_SIDE_HALF |
| |
| /** |
| * struct drm_display_mode - DRM kernel-internal display mode structure |
| * @hdisplay: horizontal display size |
| * @hsync_start: horizontal sync start |
| * @hsync_end: horizontal sync end |
| * @htotal: horizontal total size |
| * @hskew: horizontal skew?! |
| * @vdisplay: vertical display size |
| * @vsync_start: vertical sync start |
| * @vsync_end: vertical sync end |
| * @vtotal: vertical total size |
| * @vscan: vertical scan?! |
| * @crtc_hdisplay: hardware mode horizontal display size |
| * @crtc_hblank_start: hardware mode horizontal blank start |
| * @crtc_hblank_end: hardware mode horizontal blank end |
| * @crtc_hsync_start: hardware mode horizontal sync start |
| * @crtc_hsync_end: hardware mode horizontal sync end |
| * @crtc_htotal: hardware mode horizontal total size |
| * @crtc_hskew: hardware mode horizontal skew?! |
| * @crtc_vdisplay: hardware mode vertical display size |
| * @crtc_vblank_start: hardware mode vertical blank start |
| * @crtc_vblank_end: hardware mode vertical blank end |
| * @crtc_vsync_start: hardware mode vertical sync start |
| * @crtc_vsync_end: hardware mode vertical sync end |
| * @crtc_vtotal: hardware mode vertical total size |
| * |
| * The horizontal and vertical timings are defined per the following diagram. |
| * |
| * |
| * Active Front Sync Back |
| * Region Porch Porch |
| * <-----------------------><----------------><-------------><--------------> |
| * //////////////////////| |
| * ////////////////////// | |
| * ////////////////////// |.................. ................ |
| * _______________ |
| * <----- [hv]display -----> |
| * <------------- [hv]sync_start ------------> |
| * <--------------------- [hv]sync_end ---------------------> |
| * <-------------------------------- [hv]total ----------------------------->* |
| * |
| * This structure contains two copies of timings. First are the plain timings, |
| * which specify the logical mode, as it would be for a progressive 1:1 scanout |
| * at the refresh rate userspace can observe through vblank timestamps. Then |
| * there's the hardware timings, which are corrected for interlacing, |
| * double-clocking and similar things. They are provided as a convenience, and |
| * can be appropriately computed using drm_mode_set_crtcinfo(). |
| */ |
| struct drm_display_mode { |
| /* Header */ |
| /** |
| * @head: |
| * |
| * struct list_head for mode lists. |
| */ |
| struct list_head head; |
| |
| /** |
| * @base: |
| * |
| * A display mode is a normal modeset object, possibly including public |
| * userspace id. |
| * |
| * FIXME: |
| * |
| * This can probably be removed since the entire concept of userspace |
| * managing modes explicitly has never landed in upstream kernel mode |
| * setting support. |
| */ |
| struct drm_mode_object base; |
| |
| /** |
| * @name: |
| * |
| * Human-readable name of the mode, filled out with drm_mode_set_name(). |
| */ |
| char name[DRM_DISPLAY_MODE_LEN]; |
| |
| /** |
| * @status: |
| * |
| * Status of the mode, used to filter out modes not supported by the |
| * hardware. See enum &drm_mode_status. |
| */ |
| enum drm_mode_status status; |
| |
| /** |
| * @type: |
| * |
| * A bitmask of flags, mostly about the source of a mode. Possible flags |
| * are: |
| * |
| * - DRM_MODE_TYPE_BUILTIN: Meant for hard-coded modes, effectively |
| * unused. |
| * - DRM_MODE_TYPE_PREFERRED: Preferred mode, usually the native |
| * resolution of an LCD panel. There should only be one preferred |
| * mode per connector at any given time. |
| * - DRM_MODE_TYPE_DRIVER: Mode created by the driver, which is all of |
| * them really. Drivers must set this bit for all modes they create |
| * and expose to userspace. |
| * |
| * Plus a big list of flags which shouldn't be used at all, but are |
| * still around since these flags are also used in the userspace ABI: |
| * |
| * - DRM_MODE_TYPE_DEFAULT: Again a leftover, use |
| * DRM_MODE_TYPE_PREFERRED instead. |
| * - DRM_MODE_TYPE_CLOCK_C and DRM_MODE_TYPE_CRTC_C: Define leftovers |
| * which are stuck around for hysterical raisins only. No one has an |
| * idea what they were meant for. Don't use. |
| * - DRM_MODE_TYPE_USERDEF: Mode defined by userspace, again a vestige |
| * from older kms designs where userspace had to first add a custom |
| * mode to the kernel's mode list before it could use it. Don't use. |
| */ |
| unsigned int type; |
| |
| /* Proposed mode values */ |
| /** |
| * @clock: |
| * |
| * Pixel clock in kHz. |
| */ |
| int clock; /* in kHz */ |
| int hdisplay; |
| int hsync_start; |
| 118,14 → 271,74 |
|---|
| int vsync_end; |
| int vtotal; |
| int vscan; |
| /** |
| * @flags: |
| * |
| * Sync and timing flags: |
| * |
| * - DRM_MODE_FLAG_PHSYNC: horizontal sync is active high. |
| * - DRM_MODE_FLAG_NHSYNC: horizontal sync is active low. |
| * - DRM_MODE_FLAG_PVSYNC: vertical sync is active high. |
| * - DRM_MODE_FLAG_NVSYNC: vertical sync is active low. |
| * - DRM_MODE_FLAG_INTERLACE: mode is interlaced. |
| * - DRM_MODE_FLAG_DBLSCAN: mode uses doublescan. |
| * - DRM_MODE_FLAG_CSYNC: mode uses composite sync. |
| * - DRM_MODE_FLAG_PCSYNC: composite sync is active high. |
| * - DRM_MODE_FLAG_NCSYNC: composite sync is active low. |
| * - DRM_MODE_FLAG_HSKEW: hskew provided (not used?). |
| * - DRM_MODE_FLAG_BCAST: not used? |
| * - DRM_MODE_FLAG_PIXMUX: not used? |
| * - DRM_MODE_FLAG_DBLCLK: double-clocked mode. |
| * - DRM_MODE_FLAG_CLKDIV2: half-clocked mode. |
| * |
| * Additionally there's flags to specify how 3D modes are packed: |
| * |
| * - DRM_MODE_FLAG_3D_NONE: normal, non-3D mode. |
| * - DRM_MODE_FLAG_3D_FRAME_PACKING: 2 full frames for left and right. |
| * - DRM_MODE_FLAG_3D_FIELD_ALTERNATIVE: interleaved like fields. |
| * - DRM_MODE_FLAG_3D_LINE_ALTERNATIVE: interleaved lines. |
| * - DRM_MODE_FLAG_3D_SIDE_BY_SIDE_FULL: side-by-side full frames. |
| * - DRM_MODE_FLAG_3D_L_DEPTH: ? |
| * - DRM_MODE_FLAG_3D_L_DEPTH_GFX_GFX_DEPTH: ? |
| * - DRM_MODE_FLAG_3D_TOP_AND_BOTTOM: frame split into top and bottom |
| * parts. |
| * - DRM_MODE_FLAG_3D_SIDE_BY_SIDE_HALF: frame split into left and |
| * right parts. |
| */ |
| unsigned int flags; |
| |
| /* Addressable image size (may be 0 for projectors, etc.) */ |
| /** |
| * @width_mm: |
| * |
| * Addressable size of the output in mm, projectors should set this to |
| * 0. |
| */ |
| int width_mm; |
| |
| /** |
| * @height_mm: |
| * |
| * Addressable size of the output in mm, projectors should set this to |
| * 0. |
| */ |
| int height_mm; |
| |
| /* Actual mode we give to hw */ |
| int crtc_clock; /* in KHz */ |
| /** |
| * @crtc_clock: |
| * |
| * Actual pixel or dot clock in the hardware. This differs from the |
| * logical @clock when e.g. using interlacing, double-clocking, stereo |
| * modes or other fancy stuff that changes the timings and signals |
| * actually sent over the wire. |
| * |
| * This is again in kHz. |
| * |
| * Note that with digital outputs like HDMI or DP there's usually a |
| * massive confusion between the dot clock and the signal clock at the |
| * bit encoding level. Especially when a 8b/10b encoding is used and the |
| * difference is exactly a factor of 10. |
| */ |
| int crtc_clock; |
| int crtc_hdisplay; |
| int crtc_hblank_start; |
| int crtc_hblank_end; |
| 140,12 → 353,48 |
|---|
| int crtc_vsync_end; |
| int crtc_vtotal; |
| |
| /* Driver private mode info */ |
| /** |
| * @private: |
| * |
| * Pointer for driver private data. This can only be used for mode |
| * objects passed to drivers in modeset operations. It shouldn't be used |
| * by atomic drivers since they can store any additional data by |
| * subclassing state structures. |
| */ |
| int *private; |
| |
| /** |
| * @private_flags: |
| * |
| * Similar to @private, but just an integer. |
| */ |
| int private_flags; |
| |
| int vrefresh; /* in Hz */ |
| int hsync; /* in kHz */ |
| /** |
| * @vrefresh: |
| * |
| * Vertical refresh rate, for debug output in human readable form. Not |
| * used in a functional way. |
| * |
| * This value is in Hz. |
| */ |
| int vrefresh; |
| |
| /** |
| * @hsync: |
| * |
| * Horizontal refresh rate, for debug output in human readable form. Not |
| * used in a functional way. |
| * |
| * This value is in kHz. |
| */ |
| int hsync; |
| |
| /** |
| * @picture_aspect_ratio: |
| * |
| * Field for setting the HDMI picture aspect ratio of a mode. |
| */ |
| enum hdmi_picture_aspect picture_aspect_ratio; |
| }; |
| |
| 222,6 → 471,8 |
|---|
| const struct drm_display_mode *mode); |
| bool drm_mode_equal(const struct drm_display_mode *mode1, |
| const struct drm_display_mode *mode2); |
| bool drm_mode_equal_no_clocks(const struct drm_display_mode *mode1, |
| const struct drm_display_mode *mode2); |
| bool drm_mode_equal_no_clocks_no_stereo(const struct drm_display_mode *mode1, |
| const struct drm_display_mode *mode2); |
| |
| 232,7 → 483,7 |
|---|
| void drm_mode_prune_invalid(struct drm_device *dev, |
| struct list_head *mode_list, bool verbose); |
| void drm_mode_sort(struct list_head *mode_list); |
| void drm_mode_connector_list_update(struct drm_connector *connector, bool merge_type_bits); |
| void drm_mode_connector_list_update(struct drm_connector *connector); |
| |
| /* parsing cmdline modes */ |
| bool |